Pi Tape Digital Outside Diameter-Circumference for Tape Size 24in - 36in Operating instructions

Brand
Pi Tape
Model
Digital Outside Diameter-Circumference for Tape Size 24in - 36in
Type
Operating instructions

This manual is also suitable for

Pi Tape Digital Outside Diameter-Circumference for Tape Size 24in - 36in lets you easily measure the circumference or diameter of cylindrical objects with a diameter between 24 inches (609.6 mm) and 36 inches (914.4 mm). It's perfect for measuring pipes, tubes, trees, and other round objects.

The digital display shows measurements in either metric or imperial units, and it has a resolution of 0.0005 inches (0.01 mm) for diameters and 0.0005 inches (0.01 mm) for circumferences. The tape is also accurate to within ±0.003 inches (±0.09 mm) for diameters and ±0.009 inches (±0.24 mm) for circumferences.

Pi Tape Digital Outside Diameter-Circumference for Tape Size 24in - 36in lets you easily measure the circumference or diameter of cylindrical objects with a diameter between 24 inches (609.6 mm) and 36 inches (914.4 mm). It's perfect for measuring pipes, tubes, trees, and other round objects.

The digital display shows measurements in either metric or imperial units, and it has a resolution of 0.0005 inches (0.01 mm) for diameters and 0.0005 inches (0.01 mm) for circumferences. The tape is also accurate to within ±0.003 inches (±0.09 mm) for diameters and ±0.009 inches (±0.24 mm) for circumferences.

Instructions for 72” – 84” (programmed at 84”):
1) Insert the tail of tape through the window at the head of tape, then slide the tail underneath the
digital unit to prepare for setting up lines (listed on step 3 below).
NOTE: Use care when sliding the stator strip underneath the digital unit.
2) Turn on the digital unit by pushing the right button until the dashes are displayed.
3) Position the tape so that the set-up line on the head of the tape lines up exactly with the 84”
set-up line on the tail of the tape.
4) Push the right button until “SET” is displayed. The digital unit should now display the measurement
that corresponds with the set-up line.
5) Take the readings while applying 5 lbs. tension. The left button is multi-functional. Pressing it repeatedly
will display the dierent measurement modes. The measurement modes oered are metric circumference,
metric diameter, inch circumference, and inch diameter.
6) When not in use, the digital unit turns o automatically after approximately 5 minutes.
NOTE: If digital unit needs to be reset or error message is shown, turn o digital unit by pressing right button
until all characters disappear. Then repeat steps 2 through 4.
The diameter display has a resolution of 0.0005” (0.01mm) with an overall tape tolerance of ± .003” (± .09mm).
The circumference display has a resolution of 0.0005” (0.01mm) with an overall tape tolerance of
± .009" (± .24mm).
ADVISORY: Should any repairs be needed, please contact us. Opening the housing unit may result in voiding
the manufacturer’s warranty. For battery replacement, please see the Digital Battery Change Instruction Sheet.
CARE: Keep tape clean and dry.
© Copyright 2019 Pi Tape Texas LLC. All rights reserved. https://pitape.com
PI TAPE and the logo are trademarks of Pi Tape Texas, LLC, and they are registered in the USA and in 45 other countries.
Please visit https://www.pitape.com/trademarks.htm for a list of countries in which our trademarks are registered.
TO READ SIZE 72” - 84” (1828.80mm - 2133.60mm)
DIGITAL OUTSIDE DIAMETER/CIRCUMFERENCE TAPE
U.S. Patent No. 9,829,298
KNOB DISPLAY
WINDOW
SETUP LINE
MODES ACTUATOR
POWER/ SETUP ACTUATOR STATOR STRIP
HEAD OF TAPE
TAIL OF TAPE
February 2021 Rev B
  • Page 1 1

Pi Tape Digital Outside Diameter-Circumference for Tape Size 24in - 36in Operating instructions

Brand
Pi Tape
Model
Digital Outside Diameter-Circumference for Tape Size 24in - 36in
Type
Operating instructions
This manual is also suitable for

Pi Tape Digital Outside Diameter-Circumference for Tape Size 24in - 36in lets you easily measure the circumference or diameter of cylindrical objects with a diameter between 24 inches (609.6 mm) and 36 inches (914.4 mm). It's perfect for measuring pipes, tubes, trees, and other round objects.

The digital display shows measurements in either metric or imperial units, and it has a resolution of 0.0005 inches (0.01 mm) for diameters and 0.0005 inches (0.01 mm) for circumferences. The tape is also accurate to within ±0.003 inches (±0.09 mm) for diameters and ±0.009 inches (±0.24 mm) for circumferences.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents