Gamber-Johnson 7160-1096 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-1096
Type
Installation guide

This manual is also suitable for

Gamber-Johnson 7160-1096 is a clamp bracket adapter designed to mount to existing roll-formed overhead guard leg clamp brackets on forklifts with enclosed cabs. It provides a secure and versatile mounting solution for various accessories, including clam shells, work lights, and other equipment. The adapter is compatible with Linde H30T forklifts and can be attached to door latch clamp brackets or additional brackets obtained from your forklift distributor. Installation is simple, requiring only basic tools and the included hardware.

Gamber-Johnson 7160-1096 is a clamp bracket adapter designed to mount to existing roll-formed overhead guard leg clamp brackets on forklifts with enclosed cabs. It provides a secure and versatile mounting solution for various accessories, including clam shells, work lights, and other equipment. The adapter is compatible with Linde H30T forklifts and can be attached to door latch clamp brackets or additional brackets obtained from your forklift distributor. Installation is simple, requiring only basic tools and the included hardware.

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Rev.A
INST-822
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
formed overhead guard leg clamp brackets that are used on forklifts with
enclosed cabs. Linde is an example of a manufacturer that uses overhead
guard leg clamp brackets on their H30T forklift. Some clamp brackets are
used as door latches and can also be used to mount the clamp bracket
adapter (See Figure 1 below). If your specific vehicle does not have a door
latch clamp bracket, you will need to obtain a set of brackets from your
forklift distributor.
The 7160-1096 Clamp adapter bracket is designed to mount to existing roll
Figure 1.
Note: Check
the threads on the clamp bracket to verify M8 is correct for your specific
M8 mounting
hardware
vehicle.
a 7160-0371 clam shell.
2. 3/8" hardware has been provided in hardware bag 7120-0822 for attaching
bracket
Clamp adapter
clamp bracket
Door latch
Attaching the adapter to the clamp bracket:
1. Attach the adapter to the door latch or other clamp bracket with the M8
hex bolts and flat washers provided in hardware bag 7120-0822.
A second set of clamp brackets
could be obtained and mounted
in the upper mounting location if
needed for extra support
Figure 2.
© Copyright 2017 Gamber-Johnson, LLC
7160-1096
CLAMP BRACKET ADAPTER
PS-001
Printing Spec:
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Revision Form Product
INSTALLATION INSTRUCTIONS
  • Page 1 1

Gamber-Johnson 7160-1096 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-1096
Type
Installation guide
This manual is also suitable for

Gamber-Johnson 7160-1096 is a clamp bracket adapter designed to mount to existing roll-formed overhead guard leg clamp brackets on forklifts with enclosed cabs. It provides a secure and versatile mounting solution for various accessories, including clam shells, work lights, and other equipment. The adapter is compatible with Linde H30T forklifts and can be attached to door latch clamp brackets or additional brackets obtained from your forklift distributor. Installation is simple, requiring only basic tools and the included hardware.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers