Gamber-Johnson 7160-0593 Installation guide

7160-0593
Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0593
Type
Installation guide

This manual is also suitable for

Gamber-Johnson 7160-0593 is a quick release mount that can be attached to various surfaces without drilling, such as overhead guard legs, cowling, or frames with 3/8" carriage bolts. It is compatible with overhead guard legs ranging from 1 1/2" to 5" wide. It also works well with the 7160-0561 tube clamp and the 7160-0418 roll form bracket.

Gamber-Johnson 7160-0593 is a quick release mount that can be attached to various surfaces without drilling, such as overhead guard legs, cowling, or frames with 3/8" carriage bolts. It is compatible with overhead guard legs ranging from 1 1/2" to 5" wide. It also works well with the 7160-0561 tube clamp and the 7160-0418 roll form bracket.

Rev A
INST-665
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
solution, and cowling/frame as a drilled solution.
1 of 1
Please contact your reseller to obtain the hardware kit to fit tubes 2 1/2"
PS-001
lift truck. It is compatible with overhead guard legs from 1 1/2" to 5" wide.
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
roll form bracket.
mount is also compatible with the 7160-0561 tube clamp and the 7160-0418
Revision Form
The following instruction sheet is for the part number listed above.
The mount is held in place with 3/8" dia. carriage bolts. The quick release
The quick release mount assembly attaches to the overhead guard leg on the
to 5" wide.
Printing Spec:
7160-0593 - QUICK RELEASE MOUNT
This mount is designed to attach to the overhead guard leg as a no drill
INSTALLATION INSTRUCTIONS
Attach the quick release mount bottom plate to the overhead guard leg or
cowling/frame using the 3/8" carrage bolts and back plate.
7160-0593 fits tubes 1 1/2" to 2 1/2" wide.
Product
© copyright 2011 Gamber-Johnson, LLC
QUICK RELEASE
BOTTOM PLATE
TOP PLATE
QUICK RELEASE
WARNING!
TO PREVENT INJURY ENSURE LATCH
MECHANISM IS FULLY ENGAGED
  • Page 1 1

Gamber-Johnson 7160-0593 Installation guide

7160-0593
Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0593
Type
Installation guide
This manual is also suitable for

Gamber-Johnson 7160-0593 is a quick release mount that can be attached to various surfaces without drilling, such as overhead guard legs, cowling, or frames with 3/8" carriage bolts. It is compatible with overhead guard legs ranging from 1 1/2" to 5" wide. It also works well with the 7160-0561 tube clamp and the 7160-0418 roll form bracket.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents