Gamber-Johnson 7160-0512 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0512
Category
Mounting kits
Type
Installation guide

This manual is also suitable for

Gamber-Johnson 7160-0512 is a G1 Riveted Keyboard Mount that comes with a riveted pivot joint that enables dependable pivot without needing hardware adjustment. The product includes an adjustable handle that's spring-loaded to help position the keyboard's tilt, as well as a hand knob to swivel the keyboard left and right and make it easier to remove from the mount if required. It can be mounted on top of compatible Gamber-Johnson motion attachments to position the mount closer to the vehicle's dash for optimal usage.

Gamber-Johnson 7160-0512 is a G1 Riveted Keyboard Mount that comes with a riveted pivot joint that enables dependable pivot without needing hardware adjustment. The product includes an adjustable handle that's spring-loaded to help position the keyboard's tilt, as well as a hand knob to swivel the keyboard left and right and make it easier to remove from the mount if required. It can be mounted on top of compatible Gamber-Johnson motion attachments to position the mount closer to the vehicle's dash for optimal usage.

Rev.A
INST-612
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
to be used with Gamber-Johnson G1 docking stations, a Pansonic keyboard, or
I-Key keyboard. Installation instructions for other Gamber-Johnson products are
This instruction sheet is for the FZ-G1 keyboard mount only. This mount is designed
provided with each individual product.
INSTALLATION INSTRUCTIONS
Product Revision
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Printing Spec:
PS-001
G1 Riveted Keyboard Mount
Form
7160-0512
Attaching the keyboard to the
keyboard bracket
1. Insert the 1/4-20 x 2" long hex bolt
through the mounting hole on the
keyboard bracket. The mounting hole
has a hex shaped counterbore for the
head of the bolt to sit into.
2. Attach the bracket to the Keyboard
with the pan head screws provided in
the hardware bag. The I-Key keyboard
will use the (4) #8-32 x 1/4" long screws.
The Panasonic keyboard will use the (8)
M3 x 6mm long screws.
3. Next attach the washers and hand
knob in the order shown to the right.
4. Last Attach the Acorn nut to the
end of the bolt to keep the washers
and handle from falling off the bolt
when the handle is loosened to
remove the keyboard.
1/4" acorn nut
bracket
knob
1/4" flat washer
keyboard
hardware
I-Key keyboard
nylon washer
steel washer
mounting
1/4 x 2" hex bolt
© Copyright 2013 Gamber-Johnson, LLC
Attaching the G1 dock to the Keyboard Mount
1. Attach the G1 dock to the Keyboard mount as shown below with the hardware
supplied with the docking station. A Gamber-Johnson clevis could also be attached to
the back side of the keyboard mount at this same location.
Mounting the Keyboard Mount in a vehicle
The keyboard mount has 1/4-20 threaded inserts on the bottom side for mounting to
Gamber-Johnson motion attachments. Attach with the 1/4-20 x 1/2" long socket button
head screws found in the hardware bag.
The mount also has a clearance hole for a 3/8" bolt and (3) .281 square holes that will
align with the smiley face pattern on Gamber-Johnson upper poles. Hardware has not
been included for these optional mounting locations.
1/4-20 threaded inserts
.281 square holes
hole for 3/8" bolt
Features of the G1 Keyboard Mount
Riveted pivot joint - alows reliable pivot without needed adjustment of hardware.1.
Adjustable handle - spring loaded adjustable handle to position the tilt of the 2.
keyboard.
Hand Knob - to position the swivel of the keyboard left and right. Can also be 3.
loosened to remove the keyboard from the keyboard mount.
Mounts on top of standard Gamber-Johnson motion attachments to position the 4.
mount as close the vehicle dash as possible.
Adjustable lever
hand knob
pivot joint
Spring loaded
mounting holes for
standard Gamber-Johnson
Motion attachments
  • Page 1 1
  • Page 2 2
  • Page 3 3

Gamber-Johnson 7160-0512 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0512
Category
Mounting kits
Type
Installation guide
This manual is also suitable for

Gamber-Johnson 7160-0512 is a G1 Riveted Keyboard Mount that comes with a riveted pivot joint that enables dependable pivot without needing hardware adjustment. The product includes an adjustable handle that's spring-loaded to help position the keyboard's tilt, as well as a hand knob to swivel the keyboard left and right and make it easier to remove from the mount if required. It can be mounted on top of compatible Gamber-Johnson motion attachments to position the mount closer to the vehicle's dash for optimal usage.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents