RiverRidge Home 06-113 Installation guide

Brand
RiverRidge Home
Model
06-113
Type
Installation guide
ASSEMBLY INSTRUCTIONS
ADULT ASSEMBLY REQUIRED
WARNING
SEE FULL WARNING ON PAGE 2
ITEM #: 06-113 White
RiverRidge
®
Bayfield Single Door Floor Cabinet
This product requires assembly by an adult because of small parts. Care should be taken in
unpacking and assembling this item to keep small parts away from children.
Young children can be seriously injured or killed if furniture tips over.
Don’t use this item for a TV stand or place heavy objects on top of item.
Always use angle-braces or anchors to secure furniture to the wall.
THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR TOP BOARD
FOR A TOTAL OF 80 POUNDS. DO NOT LOAD EACH SHELF WITH MORE
THAN 20 POUNDS OR 80 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH
MORE THAN 20 POUNDS PER SHELF OR 80 POUNDS TOTAL WEIGHT, SHELF
MAY TIP FROM THE WALL AND CAUSE SERIOUS INJURY OR DEATH.
Top Board1PC
QTYNO DESCRIPTION
1
Left Side Panel1PC2
Right Side Panel1PC3
Upper Cross Bar1PC4
Adjustable Shelf1PC5
Shelf1PC6
Rear Lower Cross Bar1PC7
Bottom Board1PC8
Back Board
1PC9
1PC10
Door
1
2
3
4
5
6
7
10
9
8
Wood Dowel (6 x 30mm)
Cam Bolt
Cam Lock
Shelf Holder
Hinge
Screw (4 x 12mm)
Screw (4 x 35mm)
Screw (4 x 30mm)
4PCS
20PCS
12PCS
12PCS
1PC
8PCS
3PCS
2PCS
A
B
C
D
E
F
G
H
Screw (4 x 12mm)1PC
I
J
10PCS Screw (2.5 x 10mm)
Plastic Anchor1PC
K
TOOLS NEEDED FOR ASSEMBLY : FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE THIS ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you,email customer.service@ssi-rr.com
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com
L
1PC Adjustable Anchor Bracket
STEP 1
1. Insert 4 cam bolts (A) into pre-threaded holes on left side panel (2).
2. Insert 4 cam bolts (A) into pre-threaded holes on right side panel (3).
1. Insert 4 cam bolts (A) into pre-threaded holes on top board (1).
2. Attach bracket (L) to top board (1) by inserting 1 screw (I) through hole on bracket (L), then
tighten to top board (1).
1. Attach rear lower cross bar (7) to bottom board (8) by inserting 2 screws (F) through holes
on rear lower cross bar (7), then tighten to bottom board (8).
STEP 2
STEP 3
A
A
A
A
A
A
A
A
A
A
A
A
F
F
I
I
L
L
1
2
3
7
8
1. Attach 2 hinges (E) to door (10) by inserting 4 screws (G) through holes on hinges (E), then
tighten to door (10).
1. Insert 7 wood dowels (C) into wood dowel holes on left side panel (2).
2. Attach upper cross bar (4), shelf (6), bottom board (8) and rear lower cross bar (7) to left side
panel (2) by inserting wood dowels (C) into wood dowel holes and insert cam bolts (A) into cam
lock holes on upper cross bar (4), shelf (6) and bottom board (8).
3. Insert 4 cam locks (B) into cam lock holes on shelf (6) and bottom board (8), then rotate
clockwise to secure cam bolts (A) in place.
STEP 4
STEP 5
G
G
E
2
4
6
8
7
10
B
B
B
B
C
C
C
C
C
C
G
G
G
G
E
E
1. Insert 7 wood dowels (C) into wood dowel holes on right side panel (3).
2. Attach right side panel (3) to upper cross bar (4), shelf (6), bottom board (8) and rear lower
cross bar (7) to by inserting wood dowels (C) into wood dowel holes and insert cam bolts (A)
into cam lock holes on upper cross bar (4), shelf (6) and bottom board (8).
3. Insert 4 cam locks (B) into cam lock holes on shelf (6) and bottom board (8), then rotate
clockwise to secure cam bolts (A) in place.
1. Insert 6 wood dowels (C) into wood dowel holes on top board (1).
2. Attach top board (1) to left side panel (2), right side panel (3) and upper cross bar (4) by
inserting wood dowels (C) into wood dowel holes and insert cam bolts (A) into cam lock
holes on left side panel (2), right side panel (3) and upper cross bar (4).
3. Insert 4 cam locks (B) into cam lock holes on left side panel (2) and rightside panel (3), then
rotate clockwise to secure cam bolts (A) in place.
4. Insert 1 screw (F) into screw hole on upper cross bar (4), then tighten to top board (1).
STEP 6
STEP 7
1
4
2
3
B
B
B
F
B
C
C
C
C C
C
B
B
B
B
C
C
C
C
C
C
C
3
2
4
6
8
7
1. Attach back board (9) to back of cabinet by inserting 10 screws (J) through holes on back
board (9), then tighten to cabinet.
1. Insert 4 shelf holders (D) into desired position.
2. Place adjustable shelf (5) onto 4 shelf holders (D), making sure all shelf holders are at
same level.
STEP 8
STEP 9
D
D
D
D
D
J
J
J
J
J
J
J
J
J
J
5
9
1. Attach door (10) to cabinet by inserting 4 screws (G) through holes on hinges (E), then tighten
to right side panel (3).
2. Note: Tightening screw in position “a” will adjust door up or down; tightening screw in position “b”
will adjust door to or from cabinet, and tightening screw in position “c” will adjust door side to side.
G
G
G×2
G×2
b
a
a
b
c
c
STEP 10
10
E
STEP 11
H
H
K
K
K
H
H
DRYWALL
WALL ANCHOR
WITH SCREW
SCREW
ONLY
DRYWALL
OPTION #2OPTION #1
WOOD
STUD
Important: Keep assembly instructions for future reference.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts. Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make a small mark on wall through hole
on bracket (L). Move cabinet away from wall and screw 1 plastic anchor (K) into wall on pencil mark.
2. Place cabinet against wall, insert 1 screw (H) through hole on metal bracket (L), then tighten to plastic
anchor (K).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 1 screw (H) through hole on metal bracket (L),
then tighten through drywall and into wood stud.
*Tip: Anchor bracket (L) can be adjusted to correct distance from wall to cabinet as needed. Once adjusted,
be sure to re-tighten bracket inside cabinet for stability.
Thank you for purchasing this RiverRidge
®
Home item. We hope you
enjoy it and consider purchasing other RiverRidge
®
items.
To order replacement parts at no cost to you, email customer.service@ssi- rr.com,
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com
RiverRidge
®
is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016
Enjoy your new RiverRidge
®
Cabinet!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

RiverRidge Home 06-113 Installation guide

Brand
RiverRidge Home
Model
06-113
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents