RiverRidge Sort & Store 4-Bin Organizer Assembly Instructions Manual

Brand: RiverRidge

Model: Sort & Store 4-Bin Organizer

Type: Assembly Instructions Manual

ASSEMBLY INSTRUCTIONS

RiverRidge® Sort & Store 4-Bin Organizer

ITEM #:16-006 with Gray Linen Bins

ITEM #:16-005 with Brown Linen Bins

ADULT ASSEMBLY REQUIRED

This product requires assembly by an adult because of the small parts. Care should be

taken in unpacking and assembling this item to keep the small parts away from children.

WARNING

Young children can be seriously injured or killed, if furniture tips over.

Don’t use this item for a TV stand.

Use angle-braces or anchors to secure furniture to the wall.

Send requests for missing or damaged parts replacements by email to :

[email protected]

or call toll free 1-(844)-223-5201 or order parts on line at

www.riverridgehome.com

THIS STORAGE UNIT WILL HOLD UP TO 10 POUNDS ON THE TOP SHELF AND 10 POUNDS

PER BIN OR A TOTAL OF 50 POUNDS. DO NOT LOAD EACH SHELF/BIN WITH MORE THAN

10 POUNDS. IF LOADED WITH MORE THAN 10 POUNDS PER SHELF AS THIS MAY CAUSE

DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS INJURY OR DEATH.

Metal Frame

1PC

1PC

4PCS

4PCS

8PCS

4PCS

8PCS

4PCS

Top Board

Folding Bin

Bottom Bin Board

Plastic Support Bar

Plastic Insert

Wood Screw 3 x 10mm

Wood Screw 2.5 x 8mm

TOOLS NEEDED FOR ASSEMBLY : PHILIPS SCREWDRIVER (NOT INCLUDED)

THE USE OF POWER SCREWDRIVER IS NOT RECOMMENED

1.Open the folding Metal Frame (1) as shown.

2.Attach the 8 Plastic Support Bars (A) onto the tubes of the Metal Frame (1) as shown.

1.Put the Top Board (2) upside down on a soft padded surface.

2.Attach the Plastic Inserts (B) to the Top Board (2) by inserting 8 Wood Screws (C)

through the holes on the Plastic Inserts (B) and tighten to the Top Board (2).

STEP 1

STEP 1

STEP 2

STEP 2

1.Attach the Top Board (2) to Pre-assembled Metal Frame (1) by inserting the Plastic Inserts

(B) into the holes on the top of the Metal Frame (1).

2.From the back side, insert 4 Wood Screws (D) through the holes on the Metal Frame and

tighten to the Plastic Inserts (B).

1.Open the Folding Bin (3) as shown.

2.Put the Bottom Bin Board (4) into the bottom of the Folding Bin (3).

3.Keep the pull tab on the inside of the bin so that it’s easier to remove the Bottom Bin Board

(4) as needed.

4.Repeat steps 1-3 to assemble remaining bins.

STEP 3

STEP 3

STEP 4

STEP 4

1.Put the bins on the shelves.

STEP 5

STEP 5

ENJOY YOUR NEW RiverRidge® SORT & STORE 4-BIN ORGANIZER!

Attention Adults: The shelf should be checked periodically for damage or loose screws/parts.

Take appropriate action necessary to correct the hazard such as tightening of screws and taking

.nerdlihc morf yawa strap degamad yna

Thank you for purchasing this RiverRidge® Home Products item.We hope you enjoy it,and

consider purchasing other RiverRidge® items.

Send requests for missing or damaged parts replacements by email to :

[email protected]

or call toll free 1-(844)-223-5201 or order parts on line at

www.riverridgehome.com

RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016.

1
2
3
4
5
6
7

RiverRidge Sort & Store 4-Bin Organizer Assembly Instructions Manual

Brand: RiverRidge

Model: Sort & Store 4-Bin Organizer

Type: Assembly Instructions Manual

Related papers

Other documents