Page is loading ...
12276829 Rev A. 1 of 9
GoCart Mobile Cart Reorder No. G1112004
ASSEMBLY INSTRUCTIONS
Manufactured for US Endoscopy
5976 Heisley Road
Mentor, OH 44060
800-548-4873
www.steris.com
A subsidiary of STERIS Corporation
12276829 Rev A. 2 of 9
Warnings and Precautions:
Assembly Guide
1.
Remove all items from packaging and confirm the following items are present (Figure 1).
Components:
Item No. Description Quantity
1 Support Column with Cover Strips* 1
2 Rear Handle* 1
3 Shelf* 1
4 Base with Casters 1
5 Small Wire Basket* 1
6 Large Wire Basket* 1
7 Column Cover 1
*includes pre-mounted hardware
Tools:
Description Quantity
4mm Hex Key 1
5mm Hex Key 1
TX30 Hex Key 1
• The Assembly Instructions described in this manual MUST be followed, otherwise, compromised
safety, malfunction, injury to the user and/or patient, or costly damage to cart and/or other equipment
may occur.
• Modification of this equipment is not allowed. Modification may cause cart instability resulting in injury
to the user and/or patient or costly damage to the cart or other equipment.
12276829 Rev A. 3 of 9
Note: Images have been simplified for ease of viewing. Actual components may differ.
2.
Remove the four (4) screws from the bottom of the support column and set aside (Figure 2).
7
6
5
1
2
3
4
Figure 1
Figure 2
12276829 Rev A. 4 of 9
3.
Attach the base to the support column.
• Stand the support column on end, with the short, blue T-Channel cover strips on top (Figure 3).
• Place the base upside-down onto the support column.
• Thread the four (4) previously removed screws through the base, into the support column (Figure 4).
• Tighten the screws using the TX30 hex key.
4.
Stand the assembly upright. Lock the front caster wheels by engaging the break on both wheels.
5.
Remove the long blue T-Channel cover strips from the support column and set aside (Figure 5).
Note: DO NOT remove the short blue T-Channel cover strips located near the bottom of the support
column
Figure 3
Figure 4
Figure 5
12276829 Rev A. 5 of 9
6.
Install the large wire basket on the support column (Figure 6).
• Align the pre-mounted basket hardware with the front slots of the support column.
• Slide the basket down the column until it rests on the short T-channel cover strips.
• Tighten the pre-mounted hardware using the 4mm hex key.
7.
Reattach the long T-channel cover strips, allowing the bottom of the strip to rest on the large wire
basket mounting hardware.
8.
Install the shelf onto the support column (Figure 7).
• Align the pre-mounted shelf hardware with the front slots of the support column.
• Slide the shelf down the column until the shelf surface is flush with the top of the column.
• Tighten the pre-mounted hardware using the 5mm hex key.
Note: If the shelf becomes hard to position, consider laying the assembly on its side or back.
Figure 6
Figure 7
12276829 Rev A. 6 of 9
9.
Remove the short gray T-channel cover strip from the rear slot of the support column and set aside (Figure 8).
Note: DO NOT remove the long gray T-channel cover strip.
10.
Install the small wire basket on the support column (Figure 9).
• Align the pre-mounted shelf hardware with the rear support column slot.
• Slide the basket down the column until it rests on the long gray T-channel cover strip.
• Tighten the pre-mounted hardware using the 4mm hex key.
11.
Replace the small gray T-Channel cover strip, allowing it to rest on the small wire basket bracket.
12.
Install the handle onto the support column (Figure 10).
• Align the pre-mounted handle hardware with the rear support column slot.
• Slide the handle down the column until it rests on the short slot strip.
• Tighten the pre-mounted hardware using the 4mm hex key.
Figure 8
Figure 9
Figure 10
12276829 Rev A. 7 of 9
13.
Install the column cover on the top of the support column (Figure 11).
14.
Assembly complete. Consult the gi4000 Electrosurgical Generator Operating Manual for information regarding the
use, care and cleaning and maintenance of the GoCart Mobile Cart.
Product Disposal:
When disposing of the product or its parts, ensure the proper disposal of hazardous and other regulated waste in compliance
with federal, state, and local regulations.
Issued Date: January 2021
Warning: An issued or revision date for these instructions is included for the user’s information. In the event two years has elapsed
between this date and product use, the user should contact STERIS to determine if additional information is available.
Unless otherwise indicated, all marks denoted with ® or ™ are registered with the U.S. Patent and Trademark Office, or are trademarks
owned by STERIS Corporation.
Serious incidents that have occurred in relation to this medical device should be reported to the manufacturer.
US Endoscopy, a wholly owned subsidiary of STERIS Corporation.
Made in the U.S.A.
Figure 11
12276829 Rev A. 8 of 9
Explanation of symbols used on Labels and Instructions for Use
SDO (if
applicable)
Symbol and
Reference Number
Title of Symbol Meaning of Symbol
ISO 15223-1
Medical Devices
– Symbols to be
used with
medical device
labels, labelling,
and information
to be supplied
5.1.3
Date of Manufacture Indicates the date when the medical device was
manufactured
5.1.5
Batch Code
Indicates the manufacturer’s batch code
5.1.6
Catalog Number Indicates the manufacturer’s catalogue number
5.2.7
Non-Sterile
Indicates a medical device that has not been
sterilized
5.2.8
Do not use if package is
damaged
Do not use if the product sterile barrier system or its
packaging is compromised.
5.3.4
Keep dry
Indicates a medical device that needs to be
protected from moisture
5.4.1
Biological Risks
Indicates that there are potential biological risks
5.4.3
Consult instructions for use
Indicates the need for the user to consult
instructions for use
5.4.4
Caution
Consult instructions for use for cautionary
information
12276829 Rev A. 9 of 9
SDO (if
applicable)
Symbol and
Reference Number
Title of Symbol Meaning of Symbol
21 CFR 801.109
(b) (1)
N/A
Rx Only (U.S.A.)
Caution: Federal law (U.S.A.) restricts this device to sale or on the order of a physician.
N/A
N/A
Unique Device Identifier Indicates the unique device identifier
N/A
N/A
Contents
Number of devices/kits within packaging
/
