Kenwood KDC-U7056BTL User manual

Brand: Kenwood

Model: KDC-U7056BTL

Category: Car media receivers

Type: User manual

This manual is also suitable for

KDC-U7056BT

Kenwood KDC-U7056BTL brings together an array of features that make it a very versatile device that will meet the needs of the most demanding users. It can play audio from several sources: CDs, USB devices, and iPods. The USB and iPod connectivity enable the user to either play the media directly from these devices or to use the head unit as an intermediary device to control the playback of media on the iPod. The iPod control features are very comprehensive and allow you full control over the playback, including the ability to browse the iPod's file system and select specific files, artists, albums, genres, etc.

KDC-U7056DAB

KDC-U7056BT

KDC-U7056BTL

CD-RECEIVER

Quick Start Guide

B59-2188-10_01_13Stepup_QSG_M_En.indd 1 13/06/04 13:36

Quick Start Guide

Contents Before use

# WARNING

To prevent injuries or a fire, take

the following precautions:

• Stopthecarbeforeoperatingtheunit.

• Topreventashortcircuit,neverputor

leaveanymetallicobjects(suchascoins

ormetaltools)insidetheunit.

CAUTION

• Adjustthevolumesothatyoucanhear

soundoutsidethecar.Drivingwiththe

volumeadjustedtoatoohighlevelmay

causeanaccident.

• Wipeoffthedirtonthepanelwithadry

siliconorsoftcloth.

Failuretoobservethisprecautionmay

resultindamagetothemonitororunit.

Cleaning the connector

Theunitmaynotfunctionproperlyifthe

connectorbetweentheunitandfaceplate

aredirty.Detachthefaceplateandcleanthe

connectorwithacottonswabgently,being

carefulnottodamagetheconnector.

Connector

Condensation

Whenthecarisair-conditioned,moisture

maycollectonthelaserlens.Thismaycause

discreaderrors.Inthiscase,removethedisc

andwaitforthemoisturetoevaporate.

Notes

• Ifyouexperienceproblemsduring

installation,consultyourKenwooddealer.

• Whenyoupurchaseoptionalaccessories,

checkwithyourKenwooddealertomake

surethattheycanworkwithyourmodel

andinyourarea.

• CharactersthatconformtoISO8859-1

canbedisplayed.

About the Quick Start Guide.......................... 2

Before use .............................................................2

Appendix .............................................................. 4

Preparations .........................................................4

General operations ............................................ 6

Playing music (CD/USB/iPod).........................7

Listening to the radio/Digital radio ............. 8

Hands-free phoning .......................................... 9

Before installation ............................................10

Connecting wires to terminals ....................12

3 way speaker system setup ........................14

Installing/Removing the unit .......................16

Installing the Microphone unit ..................17

Installing the Digital radio antenna...........17

Specifications .....................................................21

About the Quick Start

Guide

ThisQuickStartGuidedescribesbasic

functionsofthisunit.

ForfunctionsnotdescribedinthisGuide,

refertotheInstructionManualonthe

followingwebsite:

manual.kenwood.com/edition/im362/

TorefertotheInstructionManual,abrowser

suchasInternetExplorer®7orlater,Firefox®

3.6orlater,Chrome™20orlater,Safari®5.1

orlater,iOSSafari®4.0orlater,orAndroid™

2.2orlaterisrequired.

B59-2188-10_01_13Stepup_QSG_M_En.indd 2 13/06/04 13:36

English

Before use

• Todisplaycharactersinthefollowing

language,additionalsettingisrequired.

KDC-U7056DAB  KDC-U7056BT 

-Chinese

Referto“Chinese”of<12-5.Initial

settings>.

KDC-U7056BTL 

-Arabic

-Persian

-Thai

Referto“TAGLanguage”of<12-5.Initial

settings>.

About the discs used with this unit

• ThisunitcanonlyplaytheCDswith

• Thefollowingdiscscannotbeused:

- Adiscthatisnotround

- Adiscwithcoloringontherecording

surfaceoradiscthatisdirty

- Arecordable/rewritablediscthathas

notbeenfinalized(Forthefinalization

process,refertotheinstructionmanual

thatcamewithyourdiscwriting

softwareoryourdiscrecorder.)

- An8cm(3inch)disc(Anattempt

toinsertusinganadaptercancause

malfunction.)

Handling discs

• Donottouchtherecordingsurfaceof

thedisc.

• Donotsticktapeetc.onthedisc,orusea

discwithtapestuckonit.

• Donotuseanyaccessoriesforthedisc.

• Donotuseanysolventstocleandiscs.

Useadrysiliconorsoftcloth.

• Cleanthediscbymovingthecloth

outwardfromthecenterofthedisc.

• Whenremovingadiscfromthisunit,pull

itouthorizontally.

• Ifthecenterholeoroutsiderimofadisc

hasburrs,removethembeforeinserting

adisc.

! CAUTION

• Keepbatteryoutofreachofchildren

andinoriginalpackageuntilreadyto

use.Disposeofusedbatteriespromptly.

Ifswallowed,contactaphysician

immediately.

• Donotleavethebatterynearfireor

underdirectsunlight.Afire,explosion

orexcessiveheatgenerationmayresult.

• Donotsettheremotecontrolinhot

placessuchasonthedashboard.

• TheLithiumbatteryisindangerof

explosionifreplacedincorrectly.

Replaceitonlywiththesameor

equivalenttype.

The illustrations of the display and panel appearing

in this manual are examples used to explain more

clearly how the controls are used. Therefore, what

appears on the display in the illustrations may differ

from what appears on the display on the actual

equipment, and some of the images on the display

may be inapplicable.

How to reset your unit

Iftheunitfailstooperateproperly,pressthe

Resetbutton.Theunitreturnstothefactory

settings.

Reset button

B59-2188-10_01_13Stepup_QSG_M_En.indd 3 13/06/04 13:36

Quick Start Guide

Preparations

Before using this unit for the first

time

When this unit is first turned on, the

interactive menu appears for setting the

interface language and demonstration

mode. This menu disappears when no

action is taken for 15 seconds.

 KDC-U7056BTL only:

Selecttheinterfacelanguagetodisplay

themenuitemsoftheFunctionsetting,

fromEnglish,Arabic,andPersian.

Turn[Control]knobtoselectthe

language,andthenpress[Control]knob.

 KDC-U7056BTL only:

IfyouselectedEnglishinstep1,select

thelanguagetodisplaytheaudiofile

information,fromEnglishandThai.

(ArabicorPersianisautomatically

selectedifyouselectedPersianorArabic

instep1.)

 Press[Control]knobwhenthemessage

“TocancelDEMOPressthevolumeknob”

appears.

 Turn[Control]knobtoselect“YES”,and

thenpress[Control]knob.

Theinterfacelanguageand

demonstrationmodecanalsobeset

withtheFunctionsetting.Referto<12-

4.Demonstrationmodesetting>in

Instructionmanual

Appendix

About Audio file

• PlayableAudiofiles

AAC-LC(.m4a),MP3(.mp3),WMA(.wma),

WAV(.wav)ofUSBdevice

• Playablediscmedia

CD-R/RW/ROM

• Playablediscfileformats

ISO9660Level1/2,Joliet,Longfilename.

• PlayableUSBdevices

USBmassstorageclass

• PlayableUSBdevicefilesystems

FAT12,FAT16,FAT32

Theonlinemanualabout

audiofilesisputonthesite,

www.kenwood.com/cs/ce/audiofile/.

Models of iPods/iPhones that can

be connected to this unit

Madefor

• iPodtouch(4thgeneration)

• iPodtouch(3rdgeneration)

• iPodtouch(2ndgeneration)

• iPodtouch(1stgeneration)

• iPodclassic

• iPodwithvideo

• iPodnano(6thgeneration)

• iPodnano(5thgeneration)

• iPodnano(4thgeneration)

• iPodnano(3rdgeneration)

• iPodnano(2ndgeneration)

• iPodnano(1stgeneration)

• iPhone4S

• iPhone4

• iPhone3GS

• iPhone3G

• iPhone

Forinformationonthecompatibilitywith

iPod/iPhonesoftware,visitwww.kenwood.

com/cs/ce/ipod/.

B59-2188-10_01_13Stepup_QSG_M_En.indd 4 13/06/04 13:36

English

[

]

Preparations

Adjusting the clock

 Press[Control]knobtoenterthe

Functionsettingmode.

Theitemcanbeselectedand

determinedasfollows.

”Settings”Á“Clock&Date”Á“Clock

Adjust”

Turn[Control]knobtoselecttheitem,

andpress[Control]knob.

 Turn[Control]knobtoadjustthehour,

andthenpress[Control]knob.

 Turn[Control]knobtoadjustthe

minute,andthenpress[Control]knob.

 Pressandhold[1/6]toexitsthe

Functionsettingmode.

Detaching/ Attaching the faceplate

Pressthe

Releasebutton.

• Removethefaceplateatonceafter

pressingtheReleasebutton;otherwiseit

canfalldownduetovibration.

• Thefaceplateisaprecisioncomponentof

theunitandcanbedamagedbyshocks

orjolts.

• Keepthefaceplateinitscasewhile

detached.

• Donotplacethefaceplate(andcase)in

areasexposedtodirectsunlight,excessive

heatorhumidity.Alsoavoidplaceswith

toomuchdustorthepossibilityofwater

splashing.

Release

[Control] knob (Volume knob)

B59-2188-10_01_13Stepup_QSG_M_En.indd 5 13/06/04 13:36

Quick Start Guide

General operations

Power

ToturnthepowerON,press[SRC].

ToturnthepowerOFF,pressandhold

[SRC].

Source selection

Pressing[SRC]repeatedlyswitches

amongsources.

Source Display

Standby “STANDBY”

Digital radio

[2]

“DIGITAL RADIO”

Tuner “TUNER”

USB device connected to front USB

terminal

“USB (FRONT)”

USB device connected to rear USB

terminal

“USB (REAR)”

iPod connected to front USB terminal

[1]

“iPod (FRONT)”

iPod connected to rear USB terminal

[1]

“iPod (REAR)”

Pandora® of iPod connected to front

USB terminal

[1][2][3]

“Pandora

(FRONT)”

Pandora of iPod connected to rear USB

terminal

[1][2][3]

“Pandora

(REAR)”

Pandora of device connected via

Bluetooth

[1][2][3]

“Pandora”

aha™ of iPod connected to front USB

terminal

[1]

“aha (FRONT)”

aha™ of iPod connected to rear USB

terminal

[1]

“aha (REAR)”

aha™ of device connected via

Bluetooth

[1]

“aha”

Bluetooth audio “BT AUDIO”

[1]

“CD”

Auxiliary Input

“AUX”

[1]

Thissourcecanbeselectedonlywhenitcan

beplayed.

[2]

FunctionofKDC-U7056DAB.

[3]

FunctionofKDC-U7056BT.

Volume

Turn[Control]knobtoadjustthesound

volume.

USB terminal

AUSBdeviceoriPodcanbeconnected.

TheCA-U1EX(Max.500mA)orKCA-iP102

(optionalaccessories)isrecommended

toconnectaUSBdeviceoriPod.

Auxiliary input

Aportableaudiodevicecanbe

connectedwithastereomini-plug(3.5

mmø).

[SRC]

Auxiliary input

USB terminal

[Control] knob (Volume knob)

B59-2188-10_01_13Stepup_QSG_M_En.indd 6 13/06/04 13:36

English

CA-U1EX

[1]

KCA-iP102

[1]

[

]

[

]

[

] [

]

Playing music (CD/USB/iPod)

Playing a disc

OpentheDisc slot coverupward.

InsertadiscintheDisc slot.

Whenitisinserted,thesourceis

switchedautomaticallyandplayback

starts.

ClosetheDisc slot cover.

Playing a USB device/ iPod

ConnectaUSBdeviceoriPodtotheUSB

terminal asshownabove.

Whenitisconnected,thesourceis

switchedautomaticallyandplayback

starts.

YoucanconnecttheiPodorUSBdevice

toeitheroneoftheUSBterminals

providedatthefrontandrearofthisunit.

IfyouconnectittotherearUSBterminal,

the“REARUSB”indicatorstayslit.

[1]

optionalaccessories

Selecting an audio file folder

Press[R]or[S].

Selecting a song (track or file)

Press[E]or[F].

Fast-forwarding or fast-

backwarding a song (track or file)

Pressandhold[E]or[F].

Pause and play a song (track or

file)

Pressandhold[1/6].

Music search

You can search for the song you want to

play.

 Press[1/6].

 Searchforasong.

Operation type Operation

Selecting items Turn [Control] knob.

Determining selection Press [Control] knob.

Returning to previous item Press [1/6].

Tocancelmusicsearchinaudiofilesor

iPod,Pressandhold[1/6].

Ejecting disc

OpentheDisc slot coverupward,and

press[G].

Removing USB device/ iPod

SwitchtoasourceotherthanUSB,

iPod,Pandora,andAhaRadio,andthen

removetheUSBdevice.

DatacontainedintheUSBdevice/iPod

maybedamagedifyouremoveitwhen

itisusedastheactivesource.

USB TerminalREAR USB indicator

Disc slot

Disc slot cover

[Control] knob

B59-2188-10_01_13Stepup_QSG_M_En.indd 7 13/06/04 13:37

Quick Start Guide

Listening to the radio/Digital radio

Selecting a tuner source

Press[SRC]toselect“TUNER”or“DIGITAL

RADIO”(KDC-U7056DABonly).Referto

<Sourceselection>(page6).

Selecting a band (FM or AM)

(Tuner only)

Press[R].

Selecting a station/ service

Press[E]or[F].

Theseekmodecanbechanged.Referto

<9-5.Tunersetting>or<10-1.Listening

totheDigitalRadio>inInstruction

manual

Station preset memory

 Press[R]toselectaband.(Tuneronly)

 Press[E]or[F]toselectthe

station/serviceyouwanttosaveinthe

stationpresetmemory.

 “TUNER”:Press[1/6].

“DIGITALRADIO”:Press[1/6]twice.

Press[1/6]againtoentertheMix

Stationpresetmode.Inthismode,

differentbandsandtunersources(FM,

AM,DigitalRadioetc.)canbesaved

inthesamepresetlayer,whichallows

youtorecalladesiredstationwithout

switchingbetweenbandsand/ortuner

sources.Maximumof6stationscanbe

presetintheMixStationpresetmode.

 Turn[Control]knobtoselectpreset

number(FM/DigitalRadio:“1”–“18”,

AM:“1”–“6”),andthenpressandhold

[Control]knob.

Recalling the stations in the

memory

 Press[R]toselectaband.(Tuneronly)

 Press[1/6].

 Turn[Control]knobtoselectapreset

number(FM/DigitalRadio:“1”–“18”,AM:

“1”–“6”),andthenpress[Control]knob.

IntheMixStationpresetmode,band

namesoftunersourcesaredisplayedas

follows:

FM:FMbroadcaststation

AM:AMbroadcaststation

DR:DigitalRadioservice

[SRC]

[

] [

]

[

]

[Control] knob

B59-2188-10_01_13Stepup_QSG_M_En.indd 8 13/06/04 13:37

English

Hands-free phoning

Pairing a Bluetooth device

You can pairing your Bluetooth device in

this unit.

 OperatetheBluetoothdevicetorequest

thisunitforconnection.

Thenameofthisunit(“KDC-####”)

appearsontheBluetoothdevice.

“Pressthevolumeknob”appears.

 Press[Control]knob.

ConnectiontoyourBluetoothdevice

starts,“PairingSuccess”appearsawhile

later,andthentheprevioussourceis

selected.

Whenregistrationofyourcellphoneis

completed,thephonebookofthecell

phoneisautomaticallydownloaded

tothisunit.(Ifthephonebookhasnot

beendownloadedtothisunit,operate

thecellphonetodownloadit.)

Dialing a number in the phone

book

Dial the phone number in the phone book

of your cell phone.

If the phone book has not been

downloaded to this unit, operate the cell

phone to download it.

 Press[Ú].

 Turn[Control]knobtoselect“Phone

Book”,andthenpress[Control]knob.

 Turn[Control]knobtoselectaname,

andthenpress[Control]knob.

 Turn[Control]knobtoselectaphone

number.

 Press[Ú].

Answering a phone call

Press[Ú].

Disconnecting a call

Press[Ú].

[

]

[Control] knob

B59-2188-10_01_13Stepup_QSG_M_En.indd 9 13/06/04 13:37

Quick Start Guide

# WARNING

• Theunitcanonlybeinstalledinacarwith

a12VDCpowersupply,negativeground.

• Ifyouconnecttheignitionwire(red)

andthebatterywire(yellow)tothecar

chassis(ground),youmaycauseashort

circuit,thatinturnmaystartafire.Always

connectthosewirestothepowersource

runningthroughthefusebox.

CAUTION

• Usethepowerharnessenclosedwiththis

unitforconnectingpower.Usingapower

harnessenclosedwithothermodelscan

causemalfunction.

• Installthisunitintheconsoleofyour

vehicle.

• Donottouchthemetalpartsofthisunit

duringandshortlyafteruseoftheunit.

Metalpartssuchastheheatsinkand

enclosurebecomehot.

• Mountingandwiringthisproduct

requiresskillsandexperience.Forsafety’s

sake,leavethemountingandwiringwork

toprofessionals.

• Ifyouexperienceanyproblemduring

installation,consultyourKenwooddealer.

• Disconnectthebattery’snegativeterminal

beforeinstallingtheunit.

• Insulateunconnectedwireswithvinyl

tapeorothersimilarmaterials.Toprevent

ashortcircuit,donotremovethecapson

theendsoftheunconnectedwiresand

terminals.

• Besuretogroundthisunittothecar’s

chassisagainaftermounting.

• Ifthefuseblows,firstmakesurethewires

arenottouchingotherpartstocausea

shortcircuit,andthenreplacetheoldfuse

withonewithanewthesamerating.

• Whenconnectingonlytwospeakers,

connecttheconnectorseithertoboth

ofthefrontoutputterminalsortoboth

oftherearoutputterminals(donotmix

frontandrearterminals).Forexample,if

youconnectthe+connectoroftheleft

speakertoafrontoutputterminal,do

notconnectthe - connectortoarear

outputterminal.

• Connectthespeakerwirescorrectlytothe

correspondingterminals.Theunitmay

bedamagedorfailtoworkifyoushare

the - wiresorgroundthemtoanymetal

partinthecar.

• Donotuseyourownscrews.Useonly

thesuppliedscrews.Usingwrongscrews,

coulddamagetheunit.

• Ifyourcar’signitionkeyswitchdoes

nothaveanACCposition,connectthe

ignitionwirestoapowersourcethatcan

beturnedonandoffwiththeignition

key.Ifyouconnecttheignitionwiresto

aconstant-voltagepowersource,aswith

batterywires,thebatterymaydie.

• Iftheconsolehasalid,makesureto

installtheunitsothatthefaceplatewill

nothitthelidwhenitisclosedoropened.

• Aftertheinstallingtheunit,check

whetherthebrakelamps,blinkers,wipers,

etc.onthecarareworkingproperly.

• Mounttheunitsothatthemounting

angleis30°orless.

• Receptionmaybecomepoorifthereare

metalobjectsneartheBluetoothantenna.

Bluetooth antenna unit

Before installation

B59-2188-10_01_13Stepup_QSG_M_En.indd 10 13/06/04 13:37

English

KDC-U7056DAB

• Thisunithasthecoolingfantodecrease

theinternaltemperature.Donotmount

theunitinaplacewherethecooling

fanoftheunitareblocked.Blocking

theseopeningswillinhibitthecooling

oftheinternaltemperatureandresultin

malfunction.

Cooling fan

For Good Reception

Toassuregoodreception,notethe

following:

• Communicatewiththecellphonewithin

theline-of-sightdistanceof10m(30

ft).Thecommunicationrangebecomes

shorterdependingonthesurrounding

environment.Thecommunication

rangealsobecomesshorterwhenthere

isanobstaclebetweenthisunitand

thecellphone.Theabovemaximum

communicationrange(10m)isnot

alwaysassured.

• Abroadcaststationorwalkie-talkie

locatednearbycaninterferewith

communicationduetoatoostrong

signal.

Installation accessories

.....1



.....2



Before installation

.....4



.....4



.....1 (3m)



[1]

.....1



[1]

.....1



[1]

.....3



[1]

.....1



[1]

KDC-U7056DABonly

B59-2188-10_01_13Stepup_QSG_M_En.indd 11 13/06/04 13:37

P.CONT

ILLUMI

REMOTE CONT

REMOTE INPUT

STEERING WHEEL

ANT.

CONT

MUTE

–

FRONTSW REAR

Quick Start Guide

Connecting wires to terminals

FM/AMantennainput

Digitalradioantenna

(Accessory7)

(KDC-U7056DABonly)

KDC-U7056DABonly

Frontoutput

Fuse(10A)

White/Black

Gray/Black

Green/Black

Purple/Black

White

Gray

Green

Purple

Tofrontleftspeaker

Tofrontrightspeaker

Torearrightspeaker

Torearleftspeaker

Subwooferoutput

Rearoutput

Wiringharness

(Accessory1)

Red(Ignitionwire)

Yellow(Batterywire)

Black(Groundwire)·(Tocarchassis)

Ignitionkey

switch

Carfusebox

(Mainfuse)

ACC

Carfuse

box

Battery

• SpeakerImpedance:4–8Ω

Microphone(Accessory5)

(KDC-U7056BT/

KDC-U7056BTLonly)

B59-2188-10_01_13Stepup_QSG_M_En.indd 12 13/06/04 13:37

P.CONT

ILLUMI

REMOTE CONT

REMOTE INPUT

STEERING WHEEL

ANT.

CONT

MUTE

–

FRONTSW REAR

English

Connecting wires to terminals

USBconnector(0.8m)

ToUSBdevice.

Ifnoconnectionsaremade,donotletthewirecomeoutfrom

thetab.

Blue/White

(Powercontrolwire)

Blue(Antennacontrolwire)

Orange/White

(Dimmercontrolwire)

Whenusingtheoptionalpoweramplifier,connect

thiswiretoitspowercontrolterminal.

Tocarlightcontrolswitch.

Dependingonwhatantennayouareusing,connect

eithertothecontrolterminalofthemotorantenna,

ortothepowerterminalfortheboosteramplifierof

thefilm-typeorshortpoletypeantenna.

(Max.300mA,12V)

Brown(Mutecontrolwire)

Tousethesteeringwheelremotecontrolfeature,

anexclusiveremoteadapter(notsupplied)that

matchesyourcarisrequired.

LightBlue/Yellow

(Steeringremotecontrolwire)

WhenconnectingtotheKenwoodnavigation

system:Refertoyournavigationmanual.

Microphone(Accessory5)

(KDC-U7056DABonly)

USBmaximumpowersupplycurrent

:DC5V=1A

B59-2188-10_01_13Stepup_QSG_M_En.indd 13 13/06/04 13:37

FRONTSW REAR

P.CONT

Quick Start Guide

3 way speaker system setup

White/Black

Gray/Black

Green/Black

Purple/Black

White

Gray

Green

Purple

ToMIDRangeleftspeaker

ToMIDRangerightspeaker

TorightTweeter

ToleftTweeter

MidRangeoutput

Wooferoutput

Tweeteroutput

Whenusingtheoptionalpoweramplifier,

connectthiswiretoitspowercontrol

terminal.

⁄

 Ifnoconnectionsaremade,donot

letthewirecomeoutfromthetab.

Connect the speaker wires

Wiringharness

(Accessory1)

Selectacrossovermodeaccordingto

howthespeakersareconnected.Refer

to<2-Way/3-WayCrossoverSetting>

(nextpage).

Ifyouselectawrongmode:

• Thespeakerscanbreak.

• Theoutputsoundlevelmaybe

extremelylow.

⁄

 Forhowtoconnectspeakerwires

toterminalsotherthanspeaker

terminalsandPreoutterminals,refer

to<Connectingwirestoterminals>

(page12).

Blue/White

(Powercontrolwire)

B59-2188-10_01_13Stepup_QSG_M_En.indd 14 13/06/04 13:37

English

3 way speaker system setup

2-Way/3-Way Crossover Setting

Select a crossover mode 2-way or 3-way

according to how the speakers are

connected.

 Pressthe[SRC]toselect“STANDBY”.

 Pressingdownthe[S]and[E]sforat

least3seconds,allowsyoutoenterthe

2-way/3-waycrossoversettingmode.

 Thecurrentlyselectedcrossovermode

isdisplayed.

Tochangeit,turn[Control]knobto

select“YES”,andthenpress[Control]

knob.

 Aconfirmationscreenappears.

Ifyouaresureyouwanttochangethe

crossovermode,turnthe[Control]

knobtoselect“YES”,andthenpressthe

[Control]knob.

 Thenewlyselectedcrossovermodeis

displayed,cancelingthe2-way/3-way

crossoversettingmode.

B59-2188-10_01_13Stepup_QSG_M_En.indd 15 13/06/04 13:37

Quick Start Guide

Installing/Removing the unit

Non-Japanese cars

Bend the tabs of the mounting sleeve

with a screwdriver or the like and

attach it in place.

• Makesurethattheunitisinstalled

securelyinplace.Iftheunitisunstable,it

maymalfunction(forexample,thesound

mayskip).

Japanese cars

 Removethetrimplatewithreferenceto

<Removingthetrimplate>.

 Aligntheholesintheunit(twolocations

oneachside)withthevehiclemounting

bracketandsecuretheunitwiththe

accessoryscrews.

8 mm

MAX.

ø5mm

8mm

MAX.

Removing the trim plate

 Engagethecatchpinsontheextraction

key(Accessory2)andreleasethetwo

locksontheupperpartofframe.

Liftupandpulltheframeforwardas

showninthefigure.

Catch

Lock

Accessory



Whentheupperpartofframeis

removed,removethelowerpartofframe.

• Theframecanberemovedfromthe

bottomsideinthesamemanner.

Removing the unit

 Removethetrimplatewithreferenceto

<Removingthetrimplate>.

 Removethefaceplate.

 Insertthetwoextractionkeys

(Accessory2)deeplyintotheslotson

bothsidesasshown.

 Lowertheextractionkeytowardthe

bottom,andthenpullouttheunit

halfwaywhilepressingtheextractionkey

towardstheinside.

Accessory2

• Becarefultoavoidinjuryfromthecatch

pinsontheextractionkey.

 Pulltheunitallthewayoutwithyour

hands,beingcarefulnottodropit.

B59-2188-10_01_13Stepup_QSG_M_En.indd 16 13/06/04 13:37

English

Installing the

Microphone unit

Installing the Digital

radio antenna

CAUTION

• Thisfilmantennaisexclusivelyforuse

insidethevehicle.

• Donotinstallatthefollowinglocations:

- Whereitmayblockdriver’sview

- Whereitmayobstructoperationof

safetydevicessuchasairbags

- Onmovableglasssurfacesuchasrear

hatch

• Signalstrengthwilldecreaseatthe

followinglocations:

- OnIRreflectingglassorwherecovered

withmirrortypeglassfilm

- Whereitoverlapswithgenuineradio

antenna(pattern)

- Whereitoverlapswithwindowheating

wires

- Atsideofvehicle(e.g.door,front

quarterwindow)

- Onrearwindow

- Whenglassthatblocksradiosignals

(e.g.IRreflectingglass,thermal

insulationglass)isused

- Receptionmaydecreaseduetonoise

whenwindshieldwiper,airconditioner,

ormotoristurnedon.

- Receptionmaydecreasedependingon

thedirectionofthebroadcaststation

withrespecttothevehicle(antenna).

• Besuretochecktheinstallationlocation

offilmantenna(Accessory6)before

installing.Filmantennacannotbe

re-pasted.

• Thoroughlywipeoilanddirtfromthe

pastingsurfacewiththeincludedcleaner

(Accessory9).

• Donotbendordamagethefilmantenna

(Accessory6).

• Warmthepastingsurfacebyturningon

theheaterforexample,beforeapplying.

• Itmaynotbepossibletoinstallonsome

typeofvehicle.

• Checkthecableroutingofthefilm

antenna(Accessory6)andamplifier

(Accessory7)beforepasting.

 Checktheinstallationpositionofthe

microphone(Accessory5).

 Cleantheinstallationsurface.

 Installthemicrophone.

 Laythecableuptotheunitwithit

securedatseveralpositionsusingtape

orthelike.

• Installthemicrophoneasfaraspossible

fromthecellphone.

Fix the cable with a commercial item of tape.

Accessory5

Remove the separator of

the microphone, and stick

the microphone to the

place shown above.

Adjust the direction of the

microphone to the driver.

KDC-U7056DAB only

B59-2188-10_01_13Stepup_QSG_M_En.indd 17 13/06/04 13:37

Quick Start Guide

Installing the Digital radio antenna

Installation overview

Antenna cable (3.5 m)

Accessory67

• Theantennashouldbeinstalledonthe

passengersideforsafety.

• Usecordclamper(Accessory8)to

securetheantennatothepillaratseveral

locations.

• Thedirectionoftheantennafilm

(Accessory6)changesdependingon

whetherthefilmantennaisinstalledon

therightsideorleftside.

• Separatetheantennafilm(Accessory6)

fromtheceramicline(blackpart)atthe

topofthefrontglassby150mm.

Also,placeitabout70mminsidethe

ceramiclineatthesideendofthefront

glass.(wheretheearthsheetofthe

amplifiercanbepastedonthemetalpart

ofthefrontpillar)

• Separatefromotherantennasbyatleast

100mm.

• Donotpastetheamplifier(Accessory7)

ontheceramicline(blackpart)around

thefrontglass.Becausethereisnot

enoughadhesion.

Determining the antenna

installation location

• When installing the antenna on the

left side

Accessory7

Accessory6

70 mm*

150 mm

Front pillar

Earth sheet

• When installing the antenna on the

right side

Accessory6

Accessory7

70 mm*

150 mm

Front pillar

Earth sheet

*Wheretheearthsheetofamplifierunit

(Accessory7)canbepastedonthemetal

partofthefrontpillar.

KDC-U7056DAB only

B59-2188-10_01_13Stepup_QSG_M_En.indd 18 13/06/04 13:37

English

Installing the Digital radio antenna

Antenna Installation

 Checktheinstallationlocation.

 Cleantheareawhereantennafilm

(Accessory6),amplifierunit(Accessory

7),andearthsheetarepastedwiththe

includedcleaner(Accessory9).

Thecoatingonthemetalsurfaceneed

notberemoved.

• Waituntiltheglasssurfaceis

completelydrybeforepasting.

• Iftheglasssurfaceiscold,suchas

duringwinter,warmitwithdefrosteror

dryer.

 Removetheseparator(tagI)ofantenna

filmhorizontallyandpastetheantenna

onthefrontglass.

• Removetheseparatorgently.

• Donottouchthepastingsurface

(adhesiveside)oftheantennafilm.

 Removetheseparator(tagII)ofantenna

filmverticallyandpastetheantenna

gentlywhileapplyingpressure.

 Afterpasting,rubtheelementinthe

glasssurfaceinthedirectionofthearrow

showninthefiguretobondit.

 Removetheapplicationfilm(tagIII).

• Donottouchthefeederterminalof

theelement.Also,donotapplyany

glasscleaner.

Feeder terminal

 Matchtheprotrusionoftheamplifier

withthe5ontheantennafilmand

paste.

• Donottouchthefeederterminalor

thepastingsurface(adhesiveside)of

theamplifier.

• When installing the antenna on the

right side

Accessory7

Accessory6

Earth sheet

Match the protrusion with 5

B59-2188-10_01_13Stepup_QSG_M_En.indd 19 13/06/04 13:37

Quick Start Guide

Installing the Digital radio antenna

• When installing the antenna on the

left side

Accessory7

Accessory6

Earth sheet

Match the protrusion with 5

 Removethefilmcoveringtheearth

sheetandpastetheearthsheetonthe

metalpartofthevehicle.

Providesufficientleewayfortheearth

sheetsothatitdoesnotinterferewith

theinteriorparts(frontpillarcover).

Alsotakecarethattheinteriorpartsdo

notinterferewiththeamplifier.

Accessory7

Earth sheet

Interior part

Front pillar

Front glass

 Wiretheantennacables.

• Usecordclamper(Accessory8)to

securetheantennatothepillarat

severallocations.

• Takethefollowingprecautionswhen

passingtheantennacableinsidethefront

pillarwheretheairbagisinstalled.

- Installtheamplifierpartoftheantenna

cableinfrontorabovetheairbagso

thattheantennaandtheairbagdonot

interfere.

Accessory7

Air bag

Front pillar

- Thefrontpillarcoverissecuredwith

aspecialclipwhichmayneedtobe

replacedwhenthefrontpillarcoveris

removed.

Contactyourvehicledealerfordetails

onreplacingthefrontpillarcoverand

availabilityofreplacementparts.

Clip

Interior part

KDC-U7056DAB only

B59-2188-10_01_13Stepup_QSG_M_En.indd 20 13/06/04 13:37

Page is loading ...

Kenwood KDC-U7056BTL User manual

Brand: Kenwood

Model: KDC-U7056BTL

Category: Car media receivers

Type: User manual

This manual is also suitable for

KDC-U7056BT

Download PDF

report

Kenwood KDC-U7056BTL User manual

This manual is also suitable for

Kenwood KDC-U7056BTL User manual

Related papers

Other documents