Kenwood Electronics KDC-BT73DAB User manual

Kenwood Electronics
Brand
Kenwood Electronics
Model
KDC-BT73DAB
Category
Car media receivers
Type
User manual
KDC-BT73DAB
KDC-BT53U
KDC-5057SD
CD-RECEIVER
Quick Start Guide
B59-2186-00/00 (E)© 2012 JVC KENWOOD Corporation
B59-2186-00_00_13Stepup_QSG_E_En.indd 1 12/12/17 15:05
2
|
Quick Start Guide
Contents Before use
# WARNING
To prevent injuries or a fire, take
the following precautions:
• Stopthecarbeforeoperatingtheunit.
• Topreventashortcircuit,neverputor
leaveanymetallicobjects(suchascoins
ormetaltools)insidetheunit.
!
CAUTION
• Adjustthevolumesothatyoucanhear
soundoutsidethecar.Drivingwiththe
volumeadjustedtoatoohighlevelmay
causeanaccident.
• Wipeoffthedirtonthepanelwithadry
siliconorsoftcloth.
Failuretoobservethisprecautionmay
resultindamagetothemonitororunit.
Cleaning the connector
Theunitmaynotfunctionproperlyifthe
connectorbetweentheunitandfaceplate
aredirty.Detachthefaceplateandcleanthe
connectorwithacottonswabgently,being
carefulnottodamagetheconnector.
Connector
Condensation
Whenthecarisair-conditioned,moisture
maycollectonthelaserlens.Thismaycause
discreaderrors.Inthiscase,removethedisc
andwaitforthemoisturetoevaporate.
About the Quick Start Guide.......................... 2
Before use .............................................................2
Preparations .........................................................4
General operations ............................................ 5
Playing music (CD/USB/SD/iPod) ................. 6
Listening to the radio/Digital radio ............. 8
Hands-free phoning .......................................... 9
Before installation ............................................10
Connecting wires to terminals ....................12
Installing/Removing the unit .......................14
Installing the Microphone unit ..................15
Installing the Digital radio antenna...........15
Appendix .............................................................19
About the Quick Start
Guide
ThisQuickStartGuidedescribesbasic
functionsofthisunit.
ForfunctionsnotdescribedinthisGuide,
refertotheInstructionManualonthe
followingwebsite:
manual2.jvckenwood.com/edition/im362/
TorefertotheInstructionManual,abrowser
suchasInternetExplorer®7orlater,Firefox®
3.6orlater,Chrome™20orlater,Safari®5.1
orlater,iOSSafari®4.0orlater,orAndroid™
2.2orlaterisrequired.
B59-2186-00_00_13Stepup_QSG_E_En.indd 2 12/12/17 15:05
English
|
3
Before use
Notes
• Ifyouexperienceproblemsduring
installation,consultyourKenwooddealer.
• Whenyoupurchaseoptionalaccessories,
checkwithyourKenwooddealertomake
surethattheycanworkwithyourmodel
andinyourarea.
• CharactersthatconformtoISO8859-1
canbedisplayed.
• CharactersthatconformtoISO8859-5
orISO8859-1canbedisplayed.Refer
to“Russian”of<12-7.Initialsettings>
(InstructionManual).
• TheRadioDataSystemfeaturewon’twork
wheretheserviceisnotsupportedbyany
broadcastingstation.
• USBratingisindicatedonthemainunit
underthedetachablefaceplate.
About the discs used with this unit
• ThisunitcanonlyplaytheCDswith
.
• Thefollowingdiscscannotbeused:
- Adiscthatisnotround
- Adiscwithcoloringontherecording
surfaceoradiscthatisdirty
- Arecordable/rewritablediscthathas
notbeenfinalized(Forthefinalization
process,refertotheinstructionmanual
thatcamewithyourdiscwriting
softwareoryourdiscrecorder.)
- An8cm(3inch)disc(Anattempt
toinsertusinganadaptercancause
malfunction.)
The illustrations of the display and panel appearing
in this manual are examples used to explain more
clearly how the controls are used. Therefore, what
appears on the display in the illustrations may differ
from what appears on the display on the actual
equipment, and some of the images on the display
may be inapplicable.
Handling discs
• Donottouchtherecordingsurfaceof
thedisc.
• Donotsticktapeetc.onthedisc,orusea
discwithtapestuckonit.
• Donotuseanyaccessoriesforthedisc.
• Donotuseanysolventstocleandiscs.
Useadrysiliconorsoftcloth.
• Cleanthediscbymovingthecloth
outwardfromthecenterofthedisc.
• Whenremovingadiscfromthisunit,pull
itouthorizontally.
• Ifthecenterholeoroutsiderimofadisc
hasburrs,removethembeforeinserting
adisc.
How to reset your unit
Iftheunitfailstooperateproperly,pressthe
Resetbutton.Theunitreturnstothefactory
settings.
Reset button
B59-2186-00_00_13Stepup_QSG_E_En.indd 3 12/12/17 15:05
4
|
Quick Start Guide
Preparations
Canceling the Demonstration
mode
Cancel the Demonstration mode when
you use the unit for the first time after
installation.
Press[Control]knobtocancelthe
Demonstrationmodewhenthemessage
“TocancelDEMOPressthevolumeknob”
appears(approx.15seconds).
Turn[Control]knobtoselect“YES”,and
thenpress[Control]knob.
TheDemonstrationmodecanalsobe
canceledintheFunctionSettingmode.
Referto<12-6.Demonstrationmode
setting>inInstructionmanual
Detaching/ Attaching the faceplate
Pressthe
Releasebutton.
!
• Removethefaceplateatonceafter
pressingtheReleasebutton;otherwiseit
canfalldownduetovibration.
• Thefaceplateisaprecisioncomponentof
theunitandcanbedamagedbyshocks
orjolts.
• Keepthefaceplateinitscasewhile
detached.
• Donotplacethefaceplate(andcase)in
areasexposedtodirectsunlight,excessive
heatorhumidity.Alsoavoidplaceswith
toomuchdustorthepossibilityofwater
splashing.
Release
[Control] knob (Volume knob)
B59-2186-00_00_13Stepup_QSG_E_En.indd 4 12/12/17 15:05
English
|
5
General operations
Power
ToturnthepowerON,press[SRC].
To
turnthepow
er
OFF,pressandhold
[SRC]
.
Source selection
Pressing[SRC]repeatedlyswitches
amongsources
.
Source Display
Standby “STANDBY”
Digital radio
[2]
“DIGITAL RADIO”
Tuner “TUNER”
USB device connected to front USB
terminal
“USB (FRONT)”
USB device connected to rear USB
terminal
“USB (REAR)”
iPod connected to front USB terminal
[1]
“iPod (FRONT)”
iPod connected to rear USB terminal
[1]
“iPod (REAR)”
aha™ of iPod connected to front USB
terminal
[1][2][3]
“aha (FRONT)”
aha™ of iPod connected to rear USB
terminal
[1][2][3]
“aha (REAR)”
aha™ of device connected via
Bluetooth
[1][2][3]
“aha”
Bluetooth audio
[2] [3]
“BT AUDIO”
SD
[1] [4]
“SD”
CD
[1]
“CD”
Auxiliary Input
“AUX”
[1]
Thissourcecanbeselectedonlywhenitcan
beplayed.
[2]
FunctionofKDC-BT73DAB.
[SRC]
Auxiliary input
USB terminal
[3]
FunctionofKDC-BT53U.
[4]
FunctionofKDC-5057SD.
Volume
Turn[Control]knobtoadjustthesound
volume.
USB terminal
AUSBdeviceoriPodcanbeconnected.
TheCA-U1EX(Max.500mA)orKCA-iP102
(optionalaccessories)isrecommended
toconnectaUSBdeviceoriPod.
Auxiliary input
Aportableaudiodevicecanbe
connectedwithastereomini-plug(3.5
mmø).
[Control] knob
B59-2186-00_00_13Stepup_QSG_E_En.indd 5 12/12/17 15:06
6
|
Quick Start Guide
CA-U1EX
[1]
KCA-iP102
[1]
[SRC]
[
1
/
6
]
[
G
]
[
E
/
F
] [
R
/
S
]
Playing music (CD/USB/SD/iPod)
Playing a disc
OpentheDisc slot coverupward.
InsertadiscintheDisc slot.
Whenitisinserted,thesourceis
switchedautomaticallyandplayback
starts.
ClosetheDisc slot cover.
Playing a USB device/ iPod
ConnectaUSBdeviceoriPodtotheUSB
terminal asshownabove.
Whenitisconnected,thesourceis
switchedautomaticallyandplayback
starts.
YoucanconnecttheiPodorUSBdevice
toeitheroneoftheUSBterminals
providedatthefrontandrearofthisunit.
IfyouconnectittotherearUSBterminal,
the“REARUSB”indicatorstayslit.
[1]
optionalaccessories
Playing SD card (KDC-5057SD only)
PresstheReleasebuttonanddetachthe
Faceplate.
HoldtheSDcardasshownbelowand
insertitintotheSDcardslotuntilit
clicks.
SDcard
(commerciallyavailable)
ReattachingtheFaceplate.
Press[SRC]toselect“SD”source.
Selecting an audio file folder
Press[R]or[S].
Selecting a song (track or file)
Press[E]or[F].
Fast-forwarding or fast-
backwarding a song (track or file)
Pressandhold[E]or[F].
Pause and play a song (track or
file)
Pressandhold[1/6].
USB TerminalREAR USB indicator
Disc slot
Disc slot cover
Release
[Control] knob
B59-2186-00_00_13Stepup_QSG_E_En.indd 6 12/12/17 15:06
English
|
7
Playing music (CD/USB/SD/iPod)
Music search
You can search for the song you want to
play.
Press[1/6].
Searchforasong.
Operation type Operation
Selecting items Turn [Control] knob.
Determining selection Press [Control] knob.
Returning to previous item Press [1/6].
Tocancelmusicsearchinaudiofilesor
iPod,Pressandhold[1/6].
Ejecting disc
OpentheDisc slot coverupward,and
press[G].
Removing USB device/ iPod
SwitchtoasourceotherthanUSB,iPod,
andAhaRadio,andthenremovethe
USBdevice.
DatacontainedintheUSBdevice/iPod
maybedamagedifyouremoveitwhen
itisusedastheactivesource.
Removing SD card (KDC-5057SD only)
PresstheReleasebuttonanddetachthe
Faceplate.
PushtheSDcarduntilitclicksandthen
removeyourfingerfromthecard.
Thecardpopsupsothatyoucanpullit
outwithyourfingers.
AttachingtheFaceplate.
B59-2186-00_00_13Stepup_QSG_E_En.indd 7 12/12/17 15:06
8
|
Quick Start Guide
Listening to the radio/Digital radio
Selecting a tuner source
Press[SRC]toselect“TUNER”or“DIGITAL
RADIO”(KDC-BT73DABonly).Referto
<Sourceselection>(page5).
Selecting a band (FM or AM)
(Tuner only)
Press[R].
Selecting a station/ service
Press[E]or[F].
Theseekmodecanbechanged.Refer
to<9-5.Tunersetting>or<10-9.Digital
Radiosetting>inInstructionmanual
Station preset memory
Press[R]toselectaband.(Tuneronly)
Press[E]or[F]toselectthe
station/serviceyouwanttosaveinthe
stationpresetmemory.
“TUNER”:Press[1/6].
“DIGITALRADIO”:Press[1/6]twice.
Press[1/6]againtoentertheMix
Stationpresetmode.Inthismode,
differentbandsandtunersources(FM,
AM,DigitalRadioetc.)canbesaved
inthesamepresetlayer,whichallows
youtorecalladesiredstationwithout
switchingbetweenbandsand/ortuner
sources.Maximumof6stationscanbe
presetintheMixStationpresetmode.
Turn[Control]knobtoselectpreset
number(FM/DigitalRadio:“1”–“18”,
AM:“1”–“6”),andthenpressandhold
[Control]knob.
Recalling the stations in the
memory
Press[R]toselectaband.(Tuneronly)
Press[1/6].
Turn[Control]knobtoselectapreset
number(FM/DigitalRadio:“1”–“18”,AM:
“1”–“6”),andthenpress[Control]knob.
IntheMixStationpresetmode,band
namesoftunersourcesaredisplayedas
follows:
FM:FMbroadcaststation
AM:AMbroadcaststation
DR:DigitalRadioservice
[SRC]
[
1
/
6
] [
E
/
F
]
[
R
]
[Control] knob
B59-2186-00_00_13Stepup_QSG_E_En.indd 8 12/12/17 15:06
English
|
9
Hands-free phoning
Pairing a Bluetooth device
You can pairing your Bluetooth device in
this unit.
OperatetheBluetoothdevicetorequest
thisunitforconnection.
Thenameofthisunit(“KDC-####”)
appearsontheBluetoothdevice.
“Pressthevolumeknob”appears.
Press[Control]knob.
ConnectiontoyourBluetoothdevice
starts,“PairingSuccess”appearsawhile
later,andthentheprevioussourceis
selected.
Whenregistrationofyourcellphoneis
completed,thephonebookofthecell
phoneisautomaticallydownloaded
tothisunit.(Ifthephonebookhasnot
beendownloadedtothisunit,operate
thecellphonetodownloadit.)
Dialing a number in the phone
book
Dial the phone number in the phone book
of your cell phone.
If the phone book has not been
downloaded to this unit, operate the cell
phone to download it.
Press[Ú].
Turn[Control]knobtoselect“Phone
Book”,andthenpress[Control]knob.
Turn[Control]knobtoselectaname,
andthenpress[Control]knob.
Turn[Control]knobtoselectaphone
number.
Press[Ú].
Answering a phone call
Press[Ú].
Disconnecting a call
Press[Ú].
[
Ú
]
[Control] knob
Function of KDC-BT73DAB, KDC-BT53U
B59-2186-00_00_13Stepup_QSG_E_En.indd 9 12/12/17 15:06
10
|
Quick Start Guide
# WARNING
• Theunitcanonlybeinstalledinacarwith
a12VDCpowersupply,negativeground.
• Ifyouconnecttheignitionwire(red)
andthebatterywire(yellow)tothecar
chassis(ground),youmaycauseashort
circuit,thatinturnmaystartafire.Always
connectthosewirestothepowersource
runningthroughthefusebox.
!
CAUTION
• Usethepowerharnessenclosedwiththis
unitforconnectingpower.Usingapower
harnessenclosedwithothermodelscan
causemalfunction.
• Installthisunitintheconsoleofyour
vehicle.
• Donottouchthemetalpartsofthisunit
duringandshortlyafteruseoftheunit.
Metalpartssuchastheheatsinkand
enclosurebecomehot.
• Mountingandwiringthisproduct
requiresskillsandexperience.Forsafety’s
sake,leavethemountingandwiringwork
toprofessionals.
• Ifyouexperienceanyproblemduring
installation,consultyourKenwooddealer.
• Disconnectthebattery’snegativeterminal
beforeinstallingtheunit.
• Insulateunconnectedwireswithvinyl
tapeorothersimilarmaterials.Toprevent
ashortcircuit,donotremovethecapson
theendsoftheunconnectedwiresand
terminals.
• Besuretogroundthisunittothecar’s
chassisagainaftermounting.
• Ifthefuseblows,firstmakesurethewires
arenottouchingotherpartstocausea
shortcircuit,andthenreplacetheoldfuse
withonewithanewthesamerating.
• Whenconnectingonlytwospeakers,
connecttheconnectorseithertoboth
ofthefrontoutputterminalsortoboth
oftherearoutputterminals(donotmix
frontandrearterminals).Forexample,if
youconnectthe+connectoroftheleft
speakertoafrontoutputterminal,do
notconnectthe - connectortoarear
outputterminal.
• Connectthespeakerwirescorrectlytothe
correspondingterminals.Theunitmay
bedamagedorfailtoworkifyoushare
the - wiresorgroundthemtoanymetal
partinthecar.
• Donotuseyourownscrews.Useonly
thesuppliedscrews.Usingwrongscrews,
coulddamagetheunit.
• Ifyourcar’signitionkeyswitchdoes
nothaveanACCposition,connectthe
ignitionwirestoapowersourcethatcan
beturnedonandoffwiththeignition
key.Ifyouconnecttheignitionwiresto
aconstant-voltagepowersource,aswith
batterywires,thebatterymaydie.
• Iftheconsolehasalid,makesureto
installtheunitsothatthefaceplatewill
nothitthelidwhenitisclosedoropened.
• Aftertheinstallingtheunit,check
whetherthebrakelamps,blinkers,wipers,
etc.onthecarareworkingproperly.
• Mounttheunitsothatthemounting
angleis30°orless.
• Receptionmaybecomepoorifthereare
metalobjectsneartheBluetoothantenna.
(KDC-BT73DAB,KDC-BT53Uonly)
Bluetooth antenna unit
KDC-BT73DAB
• Thisunithasthecoolingfantodecrease
theinternaltemperature.Donotmount
theunitinaplacewherethecooling
fanoftheunitareblocked.Blocking
theseopeningswillinhibitthecooling
oftheinternaltemperatureandresultin
malfunction.
Cooling fan
Before installation
B59-2186-00_00_13Stepup_QSG_E_En.indd 10 12/12/17 15:06
English
|
11
For Good Reception
Toassuregoodreception,notethe
following:
• Communicatewiththecellphonewithin
theline-of-sightdistanceof10m(30
ft).Thecommunicationrangebecomes
shorterdependingonthesurrounding
environment.Thecommunication
rangealsobecomesshorterwhenthere
isanobstaclebetweenthisunitand
thecellphone.Theabovemaximum
communicationrange(10m)isnot
alwaysassured.
• Abroadcaststationorwalkie-talkie
locatednearbycaninterferewith
communicationduetoatoostrong
signal.
Installation accessories
1
.....1
2
.....2
3
[1][2]
.....1 (3m)
4
[1]
.....1
5
[1]
.....1
6
[1]
.....3
7
[1]
.....1
[1]
KDC-BT73DABonly
[2]
KDC-BT53Uonly
Connecting the ISO Connector
ThepinarrangementfortheISOconnectors
dependsonthetypeofvehicleyoudrive.
Makesuretomaketheproperconnections
topreventdamagetotheunit.
Thedefaultconnectionforthewiring
harnessisdescribedin1below.IftheISO
connectorpinsaresetasdescribedin2,
maketheconnectionasillustrated.
Pleasebesuretoreconnectthecableas
shown2belowtoinstallthisunittothe
Volkswagen vehiclesetc.
1WhentheA-7pin(red)isconnectedwith
theignition,andtheA-4pin(yellow)is
connectedtotheconstantpowersupply
ofthevehicle’sISOconnector(default):
A-7 Pin
(Red)
A-4 Pin
(Yellow)
Unit
Vehicle
Ignition cable
(Red)
Battery cable
(Yellow)
2WhentheA-7pin(red)isconnected
totheconstantpowersupply,andthe
A-4pin(yellow)isconnectedwiththe
ignitionofthevehicle’sISOconnector:
A-7 Pin
(Red)
A-4 Pin
(Yellow)
Unit
Vehicle
Ignition cable
(Red)
Battery cable
(Yellow)
Before installation
B59-2186-00_00_13Stepup_QSG_E_En.indd 11 12/12/17 15:06
P.CONT
REMOTE CONT
REMOTE INPUT
STEERING WHEEL
ANT.
CONT
MUTE
FRONTSW REAR
LR
LR
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
12
|
Quick Start Guide
Connecting wires to terminals
FM/AMantennainput(JASO)
(KDC-BT73DAB,KDC-BT53Uonly)
KDC-BT73DABonly
Digitalradioantenna
(Accessory5)
(KDC-BT73DABonly)
Frontoutput
Subwooferoutput
Rearoutput
Microphone(Accessory3)
(KDC-BT53Uonly)
⁄ See<ConnectingtheISOConnector>(page11).
Red(Ignitionwire)
Yellow(Batterywire)
Red(A–7Pin)
Yellow(A–4Pin)
ConnectorA
ConnectorB
Connector Function Guide
Pin Numbers for
ISO Connectors
Cable Colour Functions
ExternalPower
Connector
A-4 Yellow Battery
A-5 Blue/White PowerControl
A-6 Orange/White Dimmer
A-7 Red Ignition(ACC)
A-8 Black Earth(Ground)
Connection
Speaker
Connector
B-1 Purple RearRight(+)
B-2 Purple/Black RearRight(–)
B-3 Gray FrontRight(+)
B-4 Gray/Black FrontRight(–)
B-5 White FrontLeft(+)
B-6 White/Black FrontLeft(–)
B-7 Green RearLeft(+)
B-8 Green/Black RearLeft(–)
⁄
• SpeakerImpedance:
4–8Ω
B59-2186-00_00_13Stepup_QSG_E_En.indd 12 12/12/17 15:06
P.CONT
REMOTE CONT
REMOTE INPUT
STEERING WHEEL
ANT.
CONT
MUTE
FRONTSW REAR
LR
LR
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
English
|
13
Connecting wires to terminals
FM/AMantennainput
(JASO)(KDC-5057SD
only)
FM/AMantennainput(JASO)
(KDC-BT73DAB,KDC-BT53Uonly)
USBconnector(0.8m)
ToUSBdevice.
WhenconnectingtotheKenwood
navigationsystem:Refertoyournavigation
manual.
Whenconnectingtoacartelephone:To
connecttheterminalthatisgrounded
whenthetelephoneringsorduring
conversation.(KDC-5057SDonly)
Microphone(Accessory3)
(KDC-BT73DABonly)
USBmaximumpowersupplycurrent
:DC5V=1A
Fuse(10A)
Wiringharness
(Accessory1)
Ifnoconnectionsaremade,donotletthewirecomeoutfrom
thetab.
Tousethesteeringwheelremotecontrol
feature,anexclusiveremoteadapter(not
supplied)thatmatchesyourcarisrequired.
LightBlue/Yellow(Steering
remotecontrolwire)
Red(Ignitionwire)
Yellow(Batterywire)
Blue/White(Powercontrol/
Antennacontrolwire)
Connecteithertothepowercontrol
terminalwhenusingtheoptionalpower
amplifier,ortotheantennacontrol
terminalinthevehicle.
Brown(Mutecontrolwire)
B59-2186-00_00_13Stepup_QSG_E_En.indd 13 12/12/17 15:06
14
|
Quick Start Guide
Installing/Removing the unit
Installation
Bend the tabs of the mounting sleeve
with a screwdriver or the like and
attach it in place.
<
• Makesurethattheunitisinstalled
securelyinplace.Iftheunitisunstable,it
maymalfunction(forexample,thesound
mayskip).
Removing the trim plate
Engagethecatchpinsontheextraction
key(Accessory2)andreleasethetwo
locksontheupperpartofframe.
Liftupandpulltheframeforwardas
showninthefigure.
Catch
Lock
Accessory
2
Whentheupperpartofframeis
removed,removethelowerpartofframe.
<
• Theframecanberemovedfromthe
bottomsideinthesamemanner.
Removing the unit
Removethetrimplatewithreferenceto
<Removingthetrimplate>.
Removethefaceplate.
Insertthetwoextractionkeys
(Accessory2)deeplyintotheslotson
bothsidesasshown.
Lowertheextractionkeytowardthe
bottom,andthenpullouttheunit
halfwaywhilepressingtheextractionkey
towardstheinside.
Accessory2
!
• Becarefultoavoidinjuryfromthecatch
pinsontheextractionkey.
Pulltheunitallthewayoutwithyour
hands,beingcarefulnottodropit.
B59-2186-00_00_13Stepup_QSG_E_En.indd 14 12/12/17 15:06
English
|
15
Installing the
Microphone unit
Checktheinstallationpositionofthe
microphone(Accessory3).
Cleantheinstallationsurface.
Installthemicrophone.
Laythecableuptotheunitwithit
securedatseveralpositionsusingtape
orthelike.
<
• Installthemicrophoneasfaraspossible
fromthecellphone.
Fix the cable with a commercial item of tape.
Accessory3
Remove the separator of
the microphone, and stick
the microphone to the
place shown above.
Adjust the direction of the
microphone to the driver.
KDC-BT73DAB, KDC-BT53U only KDC-BT73DAB only
Installing the Digital
radio antenna
!
CAUTION
• Thisfilmantennaisexclusivelyforuse
insidethevehicle.
• Donotinstallatthefollowinglocations:
- Whereitmayblockdriver’sview
- Whereitmayobstructoperationof
safetydevicessuchasairbags
- Onmovableglasssurfacesuchasrear
hatch
• Signalstrengthwilldecreaseatthe
followinglocations:
- OnIRreflectingglassorwherecovered
withmirrortypeglassfilm
- Whereitoverlapswithgenuineradio
antenna(pattern)
- Whereitoverlapswithwindowheating
wires
- Atsideofvehicle(e.g.door,front
quarterwindow)
- Onrearwindow
- Whenglassthatblocksradiosignals
(e.g.IRreflectingglass,thermal
insulationglass)isused
- Receptionmaydecreaseduetonoise
whenwindshieldwiper,airconditioner,
ormotoristurnedon.
- Receptionmaydecreasedependingon
thedirectionofthebroadcaststation
withrespecttothevehicle(antenna).
• Besuretochecktheinstallationlocation
offilmantenna(Accessory4)before
installing.Filmantennacannotbe
re-pasted.
• Thoroughlywipeoilanddirtfromthe
pastingsurfacewiththeincludedcleaner
(Accessory7).
• Donotbendordamagethefilmantenna
(Accessory4).
• Warmthepastingsurfacebyturningon
theheaterforexample,beforeapplying.
• Itmaynotbepossibletoinstallonsome
typeofvehicle.
• Checkthecableroutingofthefilm
antenna(Accessory4)andamplifier
(Accessory5)beforepasting.
B59-2186-00_00_13Stepup_QSG_E_En.indd 15 12/12/17 15:06
16
|
Quick Start Guide
Installing the Digital radio antenna
Installation overview
Antenna cable (3.5 m)
Accessory45
• Theantennashouldbeinstalledonthe
passengersideforsafety.
• Usecordclamper(Accessory6)to
securetheantennatothepillaratseveral
locations.
• Thedirectionoftheantennafilm
(Accessory4)changesdependingon
whetherthefilmantennaisinstalledon
therightsideorleftside.
• Separatetheantennafilm(Accessory4)
fromtheceramicline(blackpart)atthe
topofthefrontglassby150mm.
Also,placeitabout70mminsidethe
ceramiclineatthesideendofthefront
glass.(wheretheearthsheetofthe
amplifiercanbepastedonthemetalpart
ofthefrontpillar)
• Separatefromotherantennasbyatleast
100mm.
• Donotpastetheamplifier(Accessory5)
ontheceramicline(blackpart)around
thefrontglass.Becausethereisnot
enoughadhesion.
Determining the antenna
installation location
• When installing the antenna on the
left side
Accessory5
Accessory4
70 mm*
150 mm
Front pillar
Earth sheet
• When installing the antenna on the
right side
Accessory4
Accessory5
70 mm*
150 mm
Front pillar
Earth sheet
*Wheretheearthsheetofamplifierunit
(A
ccessory
5)canbepastedonthemetal
partofthefrontpillar.
KDC-BT73DAB only
B59-2186-00_00_13Stepup_QSG_E_En.indd 16 12/12/17 15:06
English
|
17
Installing the Digital radio antenna
Antenna Installation
Checktheinstallationlocation.
Cleantheareawhereantennafilm
(Accessory4),amplifierunit(Accessory
5),andearthsheetarepastedwiththe
includedcleaner(Accessory7).
Thecoatingonthemetalsurfaceneed
notberemoved.
• Waituntiltheglasssurfaceis
completelydrybeforepasting.
• Iftheglasssurfaceiscold,suchas
duringwinter,warmitwithdefrosteror
dryer.
Removetheseparator(tagI)ofantenna
filmhorizontallyandpastetheantenna
onthefrontglass.
• Removetheseparatorgently.
• Donottouchthepastingsurface
(adhesiveside)oftheantennafilm.
Removetheseparator(tagII)ofantenna
filmverticallyandpastetheantenna
gentlywhileapplyingpressure.
Afterpasting,rubtheelementinthe
glasssurfaceinthedirectionofthearrow
showninthefiguretobondit.
Removetheapplicationfilm(tagIII).
• Donottouchthefeederterminalof
theelement.Also,donotapplyany
glasscleaner.
Feeder terminal
Matchtheprotrusionoftheamplifier
withthe5ontheantennafilmand
paste.
• Donottouchthefeederterminalor
thepastingsurface(adhesiveside)of
theamplifier.
• When installing the antenna on the
right side
Accessory5
Accessory4
Earth sheet
Match the protrusion with 5
B59-2186-00_00_13Stepup_QSG_E_En.indd 17 12/12/17 15:06
18
|
Quick Start Guide
Installing the Digital radio antenna
• When installing the antenna on the
left side
Accessory5
Accessory4
Earth sheet
Match the protrusion with 5
Removethefilmcoveringtheearth
sheetandpastetheearthsheetonthe
metalpartofthevehicle.
Providesufficientleewayfortheearth
sheetsothatitdoesnotinterferewith
theinteriorparts(frontpillarcover).
Alsotakecarethattheinteriorpartsdo
notinterferewiththeamplifier.
Accessory5
Earth sheet
Interior part
Front pillar
Front glass
Wiretheantennacables.
• Usecordclamper(Accessory6)to
securetheantennatothepillarat
severallocations.
<
• Takethefollowingprecautionswhen
passingtheantennacableinsidethefront
pillarwheretheairbagisinstalled.
- Installtheamplifierpartoftheantenna
cableinfrontorabovetheairbagso
thattheantennaandtheairbagdonot
interfere.
Accessory5
Air bag
Front pillar
- Thefrontpillarcoverissecuredwith
aspecialclipwhichmayneedtobe
replacedwhenthefrontpillarcoveris
removed.
Contactyourvehicledealerfordetails
onreplacingthefrontpillarcoverand
availabilityofreplacementparts.
Clip
Interior part
KDC-BT73DAB only
B59-2186-00_00_13Stepup_QSG_E_En.indd 18 12/12/17 15:06
English
|
19
Appendix
About Audio file
• PlayableAudiofiles
AAC-LC(.m4a),MP3(.mp3),WMA(.wma),
WAV(.wav)ofUSBdevice/SDcard
• Playablediscmedia
CD-R/RW/ROM
• Playablediscfileformats
ISO9660Level1/2,Joliet,Longfilename.
• PlayableUSBdevices
USBmassstorageclass
• PlayableSDcards
SDcard(≤2GB),SDHCcard(≤32GB)
• PlayableUSBdevice/SDcardfilesystems
FAT12,FAT16,FAT32
Theonlinemanualabout
audiofilesisputonthesite,
www.kenwood.com/cs/ce/audiofile/.
Models of iPods/iPhones that can
be connected to this unit
Madefor
• iPodtouch(4thgeneration)
• iPodtouch(3rdgeneration)
• iPodtouch(2ndgeneration)
• iPodtouch(1stgeneration)
• iPodclassic
• iPodwithvideo
• iPodnano(6thgeneration)
• iPodnano(5thgeneration)
• iPodnano(4thgeneration)
• iPodnano(3rdgeneration)
• iPodnano(2ndgeneration)
• iPodnano(1stgeneration)
• iPhone4S
• iPhone4
• iPhone3GS
• iPhone3G
• iPhone
Forinformationonthecompatibilitywith
iPod/iPhonesoftware,visitwww.kenwood.
com/cs/ce/ipod/.
Requirements Aha™:
RequirementsforlisteningtotheAha™areas
follows:
iPhone or iPod touch
• UseanAppleiPhoneoriPodtouchrunning
iOS4orlater.
• Searchfor“aha”intheAppleiTunesAppStore
tofindandinstallthemostcurrentversionof
theAha™applicationonyourdevice.
• iPhone/iPodtouchconnectedtothisunitwith
aKCA-iP102.
Android™
• UseAndroidOS2.2orlater.
• DownloadtheAha™applicationtoyour
smartphonefromtheGooglePlay.
• Bluetoothmustbebuiltinandthefollowing
profilesmustbesupported.
-SPP(SerialPortProfile)
-A2DP(AdvancedAudioDistributionProfile)
NOTE
• Intheapplicationonyourdevice,loginand
createafreeaccountwithAha.
• InternetconnectionbyLTE,3G,EDGE,orWiFi.
• BecauseAha™isathird-partyservice,the
specificationsaresubjecttochangewithout
priornotice.Accordingly,compatibilitymay
beimpairedorsomeoralloftheservicesmay
becomeunavailable.
• SomeAha™functionalitycannotbeoperated
fromthisunit.
B59-2186-00_00_13Stepup_QSG_E_En.indd 19 12/12/17 15:06
B59-2186-00_00.indb 152 2012/12/17 15:14
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Kenwood Electronics KDC-BT73DAB User manual

Kenwood Electronics
Brand
Kenwood Electronics
Model
KDC-BT73DAB
Category
Car media receivers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents