Sec 1: vi List of Figures
Figure 8-4. Attaching the Antenna........................................................................................................ 1:8-7
Figure 8-5. Removing the Antenna ...................................................................................................... 1:8-7
Figure 8-6. Attaching Battery – Battery Seal ........................................................................................ 1:8-8
Figure 8-7. Attaching Battery – Vacuum Port Seal ............................................................................... 1:8-9
Figure 8-8. Attaching Battery – Slide into Position ............................................................................... 1:8-9
Figure 8-9. Squeezing the Release Latches ...................................................................................... 1:8-10
Figure 8-10. Removing the Battery ...................................................................................................... 1:8-10
Figure 8-11. Removing the Thumb Screw............................................................................................1:8-11
Figure 8-12. Engaging Hook and Seating Cover.................................................................................. 1:8-12
Figure 8-13. Securing the Cover .......................................................................................................... 1:8-12
Figure 8-14. Remove Center Screws ................................................................................................... 1:8-13
Figure 8-15. Remove Bottom Screws................................................................................................... 1:8-13
Figure 8-16. Remove Top Screws ........................................................................................................ 1:8-14
Figure 8-17. Remove Speaker Module................................................................................................. 1:8-14
Figure 8-18. Remove Flex Connectors and Expansion Board Assembly............................................. 1:8-15
Figure 8-19. Remove Antenna Coax Cable Connector........................................................................ 1:8-15
Figure 8-20. Remove Housing ............................................................................................................. 1:8-16
Figure 8-21. Remove Back Chassis Assembly from Main Chassis Assembly ..................................... 1:8-16
Figure 8-22. Remove RF Board Screw ................................................................................................ 1:8-17
Figure 8-23. Remove RF Board Assembly........................................................................................... 1:8-17
Figure 8-24. Remove VOCON Board Screw ........................................................................................ 1:8-18
Figure 8-25. Remove VOCON Board Assembly .................................................................................. 1:8-18
Figure 8-26. Remove Knobs and Fastener Hardware.......................................................................... 1:8-19
Figure 8-27. Remove Control Top Bezel Assembly.............................................................................. 1:8-19
Figure 8-28. Remove Control Top Assembly........................................................................................ 1:8-20
Figure 8-29. Serviceable Components – Main Chassis Assembly....................................................... 1:8-20
Figure 8-30. Remove Chassis Ground Contact.................................................................................... 1:8-22
Figure 8-31. Control Top Assembly and Control Top Seal.................................................................... 1:8-22
Figure 8-32. Top Bezel Assembly......................................................................................................... 1:8-23
Figure 8-33. VOCON Board Assembly................................................................................................. 1:8-23
Figure 8-34. RF Board Assembly ......................................................................................................... 1:8-24
Figure 8-35. Expansion Board Assembly ............................................................................................. 1:8-25
Figure 8-36. Back Chassis Assembly (Dual Display Versions) ............................................................ 1:8-25
Figure 8-37. Back Chassis Assembly (Top Display Version)................................................................ 1:8-27
Figure 8-38. Main Housing Assembly (Dual Display Version, Full Keypad) ......................................... 1:8-28
Figure 8-39. Main Housing Assembly (Dual Display Version, Limited Keypad) ................................... 1:8-29
Figure 8-40. Main Housing Assembly (Top Display Version)................................................................ 1:8-30
Figure 8-41. Speaker Module ............................................................................................................... 1:8-31
Figure 8-42. Speaker Grille Assembly.................................................................................................. 1:8-31
Figure 8-43. Control Top Bezel Assembly ............................................................................................ 1:8-32
Figure 8-44. Top Bezel Assembly......................................................................................................... 1:8-33
Figure 8-45. Insert VOCON Board ....................................................................................................... 1:8-34
Figure 8-46. Connect RF Board to VOCON Board............................................................................... 1:8-35
Figure 8-47. Place Back Chassis ......................................................................................................... 1:8-35
Figure 8-48. Place Housing into Main Chassis.....................................................................................1:8-36
Figure 8-49. Assemble Expansion Board Assembly ............................................................................ 1:8-36
Figure 8-50. Insert Flex Connectors ..................................................................................................... 1:8-37
Figure 8-51. Insert Speaker Module ..................................................................................................... 1:8-37
Figure 8-52. Insert Top Screws ............................................................................................................ 1:8-38
Figure 8-53. Insert Center Screws ....................................................................................................... 1:8-38
Figure 8-54. Insert Bottom Screws ....................................................................................................... 1:8-39
Figure 8-55. Attaching Vacuum Adapter............................................................................................... 1:8-41
Figure 10-1. APX 5000/ APX 6000/ APX 6000Li Dual Display (Full Keypad) Exploded View ............. 1:10-2
Figure 10-2. APX 5000/ APX 6000/ APX 6000Li Dual Display (Limited Keypad) Exploded View........ 1:10-4