Midmark 630 Barrier-Free® Universal Procedures Table (-001 thru -009) User guide

Midmark
Brand
Midmark
Model
630 Barrier-Free® Universal Procedures Table (-001 thru -009)
Type
User guide

This manual is also suitable for

Midmark 630 Barrier-Free® Universal Procedures Table (-001 thru -009) offers versatility for various medical procedures. Its powered, articulating base and Trendelenburg positioning enable smooth patient transfers and positioning. The table's 600-pound weight capacity and adjustable height enhance patient accessibility and safety. The foot-controlled base with a lockable swivel feature ensures stability during procedures. Accessories like IV poles and stirrups can be added for customized use.

Midmark 630 Barrier-Free® Universal Procedures Table (-001 thru -009) offers versatility for various medical procedures. Its powered, articulating base and Trendelenburg positioning enable smooth patient transfers and positioning. The table's 600-pound weight capacity and adjustable height enhance patient accessibility and safety. The foot-controlled base with a lockable swivel feature ensures stability during procedures. Accessories like IV poles and stirrups can be added for customized use.

1
© Midmark Corporation 2007
MA776100i
TX
RX
COM
PWR
Service & Parts Guide:
Wireless Hand / Foot Controls [9A408]
004-0556-00 Rev. (F)
Contents Page
Troubleshooting................................... 1
Association Procedure ........................ 2
Exploded Views / Parts Lists:
9A408* (complete) ........................... 3
Foot Controls (Linear & Disc) .......... 4
Hand Control .................................... 5
Troubleshooting
• When any control button is pressed, that controller
sounds a single “beep”. (All functions operate)
Cause: 1. Low Battery
2. Faulty PC board in controller
Solution: 1. Replace batteries (size: AA)
2. Replace PC board in controller
• When any control button is pressed, nothing happens.
(No “beeps”, no movement, etc.)
Check: 1. Perform Association Procedure
2. LEDs on base station PC board
If LED status is normal (see illustration):
• Check LEDs on hand / foot control PC board (see next page).
If no LEDs are illuminated, check the following:
• Modular harness (loose connections, damage, etc.)
• Power supply to chair
• Replace base station PC board if necessary.
Main PC Board
Base Station
PC Board
Modular Harness
LEDs Normal Status
(OFF - except during Association Procedure)
(ON)
(ON)
(ON - except during Association Procedure)
MA771100i
Equipment Alert
Antenna connection is very
delicate. Do not kink wire or
apply stress to connection.
Compatible with models:
641 (all)
630 (serial numbers: V430154 thru present)
2
© Midmark Corporation 2007
D2
D3
MA776200i
Troubleshooting - continued
• When any control button is pressed, nothing happens. - continued
(No “beeps”, no movement, etc.)
(see previous page for Checks 1 & 2)
Check: 3. LEDs on hand / foot control PC board
(press any button on hand / foot control)
If LEDs function properly (see illustration):
• Check antenna connection. (see parts list for detail)
• Replace antenna if necessary.
If LEDs do not function properly:
• Replace batteries in controller (size: AA)
• Replace hand / foot control touch membrane.
• Replace hand / foot control PC board if necessary.
LEDs Normal Status
(OFF - except during Association Procedure)
(ON
only when a button on that control is pressed)
Hand / Foot Control
PC Board
(Hand control shown. Foot control
PC board is the same)
Association Procedure
The wireless controllers will only function with the chair they have been “associated” with.
This prevents unwanted movement in locations with more than one chair.
Each wireless controller’s association is preset at the factory. This procedure is only required in
the event of a malfunction, if a new controller is purchased*, or if you are attempting to use the
controller with a chair other than the one it was originally associated with.
* NOTE: The chair’s PC board only stores the last two associated controllers. To ensure proper
operation, Midmark recommends reassociating both controllers (hand & foot) if a new
controller is purchased.)
Association Procedure:
A. Using the wired hand or foot control, press & hold
the Stop & Home buttons simultaneously.
(after two seconds you will hear a single “beep”)
B*. Using the wireless hand control, press & hold
the Stop & Home buttons until you hear three “beeps”.
(One long “beep” indicates the association failed. Unplug unit for
one minute and repeat Steps A & B.)
C. Check for proper operation of wireless hand control.
D. Repeat procedure for wireless foot control.
* Note: Step B must be performed within 3 seconds of Step A.
3
© Midmark Corporation 2007
3
4
5
6
4
MA77600i
7
1
2
3
4
5
6
4
MA77600i
7
1
2
Item Description Qty.
1 Wireless Controls Accessory
w/ Linear Foot Control
(incl. 3 thru 8) ......
1
2 Wireless Controls Accessory
w/ Disc Foot Control
(incl. 3 thru 8) .........
1
3 • Wireless Hand Control Assy. ................... 1
4 • Antenna
(includes wiring & nut) ................
1
5 • Base Station PC Board ............................. 1
6 • Modular Harness ...................................... 1
7 • Batteries
(size: AA) ...................................
4
8 • FCC Label Set -
(not shown) ...................
1
Non-Prog:
9A408003
Prog:
9A408004
Non-Prog:
9A408007
Prog:
9A408008
Non-Prog:
002-1076-00
Prog:
002-1076-01
015-2177-00
015-2131-00
015-2086-00
015-2149-00
Exploded View / Parts List: 9A408 (complete)
NOTE: Refer to the following page for foot control only.
Rev. 2/19/15
4
© Midmark Corporation 2007
1
2
Foot Control only
Midmark Corporation
60 Vista Drive
Versailles, OH 45380-0286
Phone: 937-526-3662
Fax: 937-526-5542
www.midmark.com
Item Description Qty.
1 Wireless Foot Control: Linear ........................ 1
2 Wireless Foot Control: Disc .......................... 1
Non-Prog:
002-1290-02
Prog:
002-1290-01
Non-Prog:
002-1290-04
Prog:
002-1290-03
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Midmark 630 Barrier-Free® Universal Procedures Table (-001 thru -009) User guide

Midmark
Brand
Midmark
Model
630 Barrier-Free® Universal Procedures Table (-001 thru -009)
Type
User guide
This manual is also suitable for

Midmark 630 Barrier-Free® Universal Procedures Table (-001 thru -009) offers versatility for various medical procedures. Its powered, articulating base and Trendelenburg positioning enable smooth patient transfers and positioning. The table's 600-pound weight capacity and adjustable height enhance patient accessibility and safety. The foot-controlled base with a lockable swivel feature ensures stability during procedures. Accessories like IV poles and stirrups can be added for customized use.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents