Raymarine eci-100 Installation Instructions Manual

Brand: Raymarine

Model: eci-100

Type: Installation Instructions Manual

ECI-100

Engine & Contr o l

Interf ace

Installation instructions

English

Date: 12-2013

Document number: 87202-2-EN

ECI–100

Trademark and patents notice

Autohelm, hsb

, RayTech Navigator, Sail Pilot, SeaTalk, SeaTalk

, SeaTalk

and Sportpilot are registered trademarks of

Raymarine UK Limited. RayTalk, Seahawk, Smartpilot, Pathnder and Raymarine are registered trademarks of Raymarine

Holdings Limited.

FLIR is a registered trademark of FLIR Systems, Inc. and/or its

subsidiaries.

All other trademarks, trade names, or company names referenced herein are used for identication only and are the property

of their respective owners.

This product is protected by patents, design patents, patents pending, or design patents pending.

Fair Use Statement

You may print no more than three copies of this manual for your own use. You may not make any further copies or distribute or use

the manual in any other way including without limitation exploiting the manual commercially or giving or selling copies to third parties.

Contents

Chapter 1 Important information

Certified Installation

Water ingress

Disclaimer

EMC installation guidelines

Suppression ferrites

Connections to other equipment

Declaration of conformity

Product disposal

Warranty registration

IMO and SOLAS

Technical accuracy

Chapter2Documentandproduct

information

2.1 Document information

2.2 Product overview

Chapter 3 Planning the installation

3.1 Installation checklist

3.2 Parts supplied

3.3 Required additional components

3.4 Compatible multifunction displays

3.5 Compatible autopilot systems

3.6 Software updates

3.7 Tools required

3.8 Typical systems

3.9 Warnings and cautions

3.10 General location requirements

3.11 Product dimensions

Chapter 4 Cables and connections

4.1 General cabling guidance

4.2 Connections overview

4.3 Power connection

4.4 Data and control connections

Chapter 5 Mounting

5.1 Mounting the unit

Chapter6Systemchecksand

troubleshooting

6.1 Initial power on test

6.2 Further information

6.3 Troubleshooting

Chapter 7 Maintenance

7.1 Routine checks

7.2 Unit cleaning instructions

Chapter 8 Technical support

8.1 Raymarine customer support

8.2 Viewing product information

Chapter 9 Technical specification

9.1 Technical specification

Chapter 10 Spares and accessories

10.1 Spares and accessories

10.2 SeaTalk

cables and accessories

Appendix A Supported messages

Chapter1:Importantinformation

CertiedInstallation

RaymarinerecommendscertiedinstallationbyaRaymarine

approvedinstaller.Acertiedinstallationqualiesforenhanced

productwarrantybenets.ContactyourRaymarinedealerfor

furtherdetails,andrefertotheseparatewarrantydocument

packedwithyourproduct.

Warning:Productinstallationand

operation

Thisproductmustbeinstalledandoperatedin

accordancewiththeinstructionsprovided.Failure

todosocouldresultinpersonalinjury,damageto

yourvesseland/orpoorproductperformance.

Warning:Productgrounding

Beforeapplyingpowertothisproduct,ensureithas

beencorrectlygrounded,inaccordancewiththe

instructionsinthisguide.

Warning:Positivegroundsystems

Donotconnectthisunittoasystemwhichhas

positivegrounding.

Warning:Powersupplyvoltage

Connectingthisproducttoavoltagesupplygreater

thanthespeciedmaximumratingmaycause

permanentdamagetotheunit.Refertothe

Technicalspecicationsectionforvoltagerating.

Warning:Switchoffpowersupply

Ensurethevessel’spowersupplyisswitchedOFF

beforestartingtoinstallthisproduct.DoNOT

connectordisconnectequipmentwiththepower

switchedon,unlessinstructedinthisdocument.

Caution:Powersupplyprotection

Wheninstallingthisproductensurethepower

sourceisadequatelyprotectedbymeansofa

suitably-ratedfuseorautomaticcircuitbreaker.

Caution:Serviceandmaintenance

Thisproductcontainsnouserserviceable

components.Pleasereferallmaintenance

andrepairtoauthorizedRaymarinedealers.

Unauthorizedrepairmayaffectyourwarranty.

Wateringress

Wateringressdisclaimer

Althoughthewaterproofratingcapacityofthisproductmeets

thestatedIPXstandard(refertotheproduct’sTechnical

Specication),waterintrusionandsubsequentequipment

failuremayoccuriftheproductissubjectedtocommercial

high-pressurewashing.Raymarinewillnotwarrantproducts

subjectedtohigh-pressurewashing.

Disclaimer

Raymarinedoesnotwarrantthatthisproductiserror-freeorthat

itiscompatiblewithproductsmanufacturedbyanypersonor

entityotherthanRaymarine.

Raymarineisnotresponsiblefordamagesorinjuriescausedby

youruseorinabilitytousetheproduct,bytheinteractionofthe

productwithproductsmanufacturedbyothers,orbyerrorsin

informationutilizedbytheproductsuppliedbythirdparties.

EMCinstallationguidelines

Raymarineequipmentandaccessoriesconformtothe

appropriateElectromagneticCompatibility(EMC)regulations,

tominimizeelectromagneticinterferencebetweenequipment

andminimizetheeffectsuchinterferencecouldhaveonthe

performanceofyoursystem

CorrectinstallationisrequiredtoensurethatEMCperformance

isnotcompromised.

ForoptimumEMCperformancewerecommendthatwherever

possible:

•Raymarineequipmentandcablesconnectedtoitare:

–Atleast1m(3ft)fromanyequipmenttransmittingor

cablescarryingradiosignalse.g.VHFradios,cablesand

antennas.InthecaseofSSBradios,thedistanceshould

beincreasedto7ft(2m).

–Morethan2m(7ft)fromthepathofaradarbeam.A

radarbeamcannormallybeassumedtospread20degrees

aboveandbelowtheradiatingelement.

•Theproductissuppliedfromaseparatebatteryfromthatused

forenginestart.Thisisimportanttopreventerraticbehavior

anddatalosswhichcanoccuriftheenginestartdoesnot

haveaseparatebattery.

•Raymarinespeciedcablesareused.

•Cablesarenotcutorextended,unlessdoingsoisdetailedin

theinstallationmanual.

Note:Whereconstraintsontheinstallationprevent

anyoftheaboverecommendations,alwaysensurethe

maximumpossibleseparationbetweendifferentitemsof

electricalequipment,toprovidethebestconditionsforEMC

performancethroughouttheinstallation

Suppression ferrites

Raymarine cables may be 

tted with suppression ferrites. These

are important for correct EMC performance. If a ferrite has to be

removed for any purpose (e.g. installation or maintenance, it

must be replaced in the original position before the product is

used.

Use only ferrites of the correct type, supplied by Raymarine

authorized dealers.

Where an installation requires multiple ferrites to be added to a

cable, additional cable clips should be used to prevent stress on

the connectors due to the extra weight of the cable.

Connections to other equipment

Requirement for ferrites on non-Raymarine cables

If your Raymarine equipment is to be connected to other

equipment using a cable not supplied by Raymarine, a

suppression ferrite MUST always be attached to the cable near

the Raymarine unit.

Declaration of conformity

Raymarine UK Ltd. declares that this product is compliant with

the essential requirements of EMC directive 2004/108/EC.

Importantinformation

Product disposal

Dispose of this product in accordance with the WEEE Directive.

The Waste Electrical and Electronic Equipment (WEEE

Directive requires the recycling of waste electrical and electronic

equipment. Whilst the WEEE Directive does not apply to some

Raymarine products, we support its policy and ask you to be

aware of how to dispose of this product.

Warranty registration

It is important that you register your product to receive full

warranty benefits. Your unit package includes a bar code label

indicating the serial number of the unit. You will need this serial

number when registering your product online. You should retain

the label for future reference.

IMO and SOLAS

The equipment described within this document is intended for

use on leisure marine boats and workboats not covered by

International Maritime Organization (IMO) and Safety of Life at

Sea (SOLAS) Carriage Regulations.

Technical accuracy

To the best of our knowledge, the information in this document

was correct at the time it was produced. However, Raymarine

cannot accept liability for any inaccuracies or omissions it may

contain. In addition, our policy of continuous product

improvement may change specifications without notice. As a

result, Raymarine cannot accept liability for any differences

between the product and this document. Please check the

Raymarine website to ensure you have the most up-to-date

version(s) of the documentation for your product.

ECI–100

Chapter2:Documentandproductinformation

Chaptercontents

• 2.1 Document information

• 2.2 Product overview

Documentandproductinformation

2.1Documentinformation

Thisdocumentcontainsimportantinformationrelatedtothe

installationofyourRaymarineproduct.

Thedocumentincludesinformationtohelpyou:

•planyourinstallationandensureyouhaveallthenecessary

equipment;

•installandconnectyourproductaspartofawidersystemof

connectedmarineelectronics;

•troubleshootproblemsandobtaintechnicalsupportifrequired.

Applicable products

This document is applicable to the following products:

PartnumberName

Descrip-

tion

E70227

ECI-100Engine&

Control

Interface

Documentconventions

Thefollowingconventionsareusedthroughoutthisdocument

whenreferringto:

TypeExampleConvention

Proceduresfor

performingspecic

tasksusinga

multifunctiondisplay.

SelectTransducer

Set-Up.

Theterm“Select”is

usedtorefertothe

actionofselecting

amenuoptionona

multifunctiondisplay,

usingthetouchscreen

orphysicalcontrols,

dependingondisplay

variant.

Proceduresfor

navigatingmenu

hierarchiesona

multifunctiondisplay.

Internalsonarmodule

isturnedofffromthe

Fishnderapplication

menu:Menu>Set-up

>SounderSet-up>

InternalSounder.

Menuhierarchies

areusedinthis

documenttoprovide

aquicksummary

onhowtoaccess

aparticularfunction

onthemultifunction

display.

Documentillustrations

Yourproductmaydifferslightlyfromthatshowninthe

illustrationsinthisdocument,dependingonproductvariantand

dateofmanufacture.

Allimagesareprovidedforillustrationpurposesonly.

Productdocumentation

Thefollowingdocumentationisapplicabletoyourproduct:

DescriptionPartnumber

ECI–100Installationinstructions

InstallationofanECI–100unitandconnectiontoa

widersystemofmarineelectronics.

88026/87202

SeaTalk

Referencemanual

Detailstheplanningandoperationofsystemsbased

ontheSeaTalk

network.

81300

NewaSeries,cSeries,eSeriesInstallationand

operationinstructions

DetailstheoperationoftheDataapplicationand

autopilotintegrationforNewaSeries,cSeries,eSeries

multifunctiondisplays.

81337

gSSeriesInstallationandoperationinstructions

DetailstheoperationoftheDataapplicationand

autopilotintegrationforgSSeriesmultifunctiondisplays.

81345

2.2Productoverview

TheunitconnectstoaSeaT alk

backboneorSeaTalk

device

andtoanengine’scontrollerareanetwork(CANbus).J1939

andNMEA2000engineandtransmissiondataandsteering

controlmessagesareconvertedandthentransmittedonto

theSeaT alk

network;Enablingenginedatatransmissionand

steeringcontrol.

D12968-1

TheECI–100canbeusedasanengineinterfaceandasteering

controlinterfaceatthesametime.

Theproductincludesthefollowingfeatures:

Engineinterface

•Attachesdirectlytosupportedengines’CANbus.

•Receivesengineandtransmissiondata,warnings,faultsand

alarmsfromtheengine’sCANbusandtransmitsthemon

SeaTalk

Steeringcontrol

•Attachesdirectlytosupported‘drive-by-wire’steeringcontrol

systems.

•ReceivessteeringmessagesfromaconnectedEV2

Evolution

autopilotandtransmitsonthethirdpartysteering

controlsystem.

•Receivesfeedbackfromthesteeringcontrolsystemand

transmitsonSeaT alk

TheECI–100provideselectricalIsolationbetweenthethirdparty

CANbusandSeaTalk

Supportedengines/steeringsystems

TheunitcanbeusedtoconnectdirectlyintoengineCAN

buses,whichusetheJ1939and/orNMEA2000standardand

drive-by-wiresteeringcontrolsystems,usedbymanymarine

enginemanufacturersincluding:

Supportedengines

•VolvoPentaIPS

•YamahaMarineCommandLinkPlus

•Otherinboard,outboardandsterndrivepropulsionsystems

whichusestandardJ1939orNMEA2000protocols

Supporteddrive-by-wiresteeringsystems

•VolvoPentaIPS

•VolvoPentaAquamaticjoystickcontrol

•YamahaHelmMaster

Note:Forsystemscontainingmorethan2steeringengines

refertotheRaymarinewebsiteforcompatibilityinformation.

ECI–100

Chapter3:Planningtheinstallation

Chaptercontents

• 3.1 Installation checklist

• 3.2 Parts supplied

• 3.3 Required additional components

• 3.4 Compatible multifunction displays

• 3.5 Compatible autopilot systems

• 3.6 Software updates

• 3.7 Tools required

• 3.8 Typical systems

• 3.9 Warnings and cautions

• 3.10 General location requirements

• 3.11 Product dimensions

Planningtheinstallation

3.1Installationchecklist

Installationincludesthefollowingactivities:

InstallationTask

1Planyoursystem.

Obtainallrequiredequipmentandtools.

Siteallequipment.

4Routeallcables.

Drillcableandmountingholes.

6Makeallconnectionsintoequipment.

Secureallequipmentinplace.

8Poweronandtestthesystem.

Schematicdiagram

Aschematicdiagramisanessentialpartofplanningany

installation.Itisalsousefulforanyfutureadditionsor

maintenanceofthesystem.Thediagramshouldinclude:

•Locationofallcomponents.

•Connectors,cabletypes,routesandlengths.

3.2Partssupplied

Thefollowingitemsaresuppliedwithyourproduct.

ItemDescriptionQuantity

ECI–100(Engine&Control

Interface)

400mm(1.3ft)SeaTalk

spur

cable(A06038)

Documentpack1

Mountingscrews2

ECI–100

3.3Requiredadditionalcomponents

Thisproductformspartofasystemofelectronicsandrequires

thefollowingadditionalcomponentsforfulloperation.

•Enginespecicadaptorcablesarerequiredtoconnectyour

unittotheengine(s)CANbus.RefertoChapter10Spares

andaccessoriesforsuitableadaptorcables.

•T oenablesteeringcontrolacompatibleRaymarineautopilotis

required.Referto3.5Compatibleautopilotsystemsforalist

ofcompatibleproducts.

•T odisplayenginedataacompatibleRaymarinemultifunction

displayisrequired.Referto3.4Compatiblemultifunction

displaysforalistofcompatibleproducts.

3.4Compatiblemultifunctiondisplays

ThisproductiscompatiblewiththefollowingRaymarine

multifunctiondisplays.

•NewaSeries,NewcSeries,NeweSeries.

•gSSeries.

Multifunctiondisplaysoftwarerequirements

TheoperationofthisproductrequiresthatyourRaymarine

multifunctiondisplayisrunningsoftwareversion8orlater.

Planningtheinstallation

3.5Compatibleautopilotsystems

Forsteeringcontrolthisproductiscompatiblewiththefollowing

Raymarineautopilots.

•EV2—Evolution

autopilot

3.6Softwareupdates

Thesoftwarerunningontheproductcanbeupdated.

• Raymarine periodically releases software updates to improve

product performance and add new features.

• You can update the software for your product using a

connected and compatible multifunction display.

• Refer to raymarine for the latest software updates and the

software update procedure for your product.

• If in doubt as to the correct procedure for updating your

product software, refer to your dealer or Raymarine technical

support.

Caution:Downloadingsoftware

updates

Thesoftwareupdateprocessiscarriedoutatyour

ownrisk.Beforeinitiatingtheupdateprocess

ensureyouhavebackedupanyimportantles.

Ensurethattheunithasareliablepowersupply

andthattheupdateprocessisnotinterrupted.

Damagecausedbyincompleteupdatesarenot

coveredbyRaymarinewarranty.

Bydownloadingthesoftwareupdatepackage,you

agreetotheseterms.

ECI–100

3.7Toolsrequired

Productinstallationrequiresthefollowingtools:

ItemDescriptionQuantity

Powerdrill1

Pozidrivescrewdriver1

Drillbitofappropriatesize*

Note:*Theappropriatedrillbitsizeisdependentonthe

thicknessandmaterialofthemountingsurface.

3.8Typicalsystems

Important:DoNOTconnect2ormoreECIunitstothesame

engineCANbus.

Example:basicsystem—engineinterfaceonly

Intheexamplebelowtheunitisusedasanengineinterface

only,theunitwillinterfacewithallenginesonthesameCAN

bus.Inthiscongurationtheunitcannotcontrolthevessel’s

steeringsystem.

12 V dc

SeaTalk

D12969-1

Note:Theillustrationaboveshowsthevariousproductsthat

canbeconnectedinatypicalsystem.Forinformationonhow

toconnecttheproducts,refertotheChapter4Cablesand

connectionssection.Forinformationonavailablecablesand

accessories,refertotheChapter10Sparesandaccessories

section.

ItemDescription

Multifunctiondisplay

Vesselengine(s)(Connectiontoengine’sCANbus)

Engine-specicadaptorcable

ECIunit

SeaTalk

5–wayblock

Example:IndependentengineCANbusnetworks

Onamulti-enginevesselthathasdedicatedCANbusnetworks

foreachengine,then1unitpernetworkisrequired.

12 V dc

SeaTalk

D12970-1

Note:Theillustrationaboveshowsthevariousproductsthat

canbeconnectedinatypicalsystem.Forinformationonhow

toconnecttheproducts,refertotheChapter4Cablesand

connectionssection.Forinformationonavailablecablesand

accessories,refertotheChapter10Sparesandaccessories

section.

Planningtheinstallation

ItemDescription

Multifunctiondisplay

Vesselengines(Connectiontoengine’sCANbus)

Enginespecicadaptorcables

ECIunits

SeaTalk

5–wayblock

Example:expandedsystem

Intheexamplebelowtheunitisusedasbothengineinterface

andsteeringcontrolinterfacesimultaneously.

STBY

12 V dc

SeaTalk

D12971-2

Note:Theillustrationaboveshowsthevariousproductsthat

canbeconnectedinatypicalsystem.Forinformationonhow

toconnecttheproducts,refertotheChapter4Cablesand

connectionssection.Forinformationonavailablecablesand

accessories,refertotheChapter10Sparesandaccessories

section.

ItemDescription

Multifunctiondisplay

Vesselengine(s)andsteering(ConnectiontoengineCAN

bus)

Engine-specicadaptorcable

ECIunit

SeaTalk

5–wayblock

6EV2—Evolution

autopilot

SeaTalk

Pilotcontrolhead

SeaTalk

instrumentdisplay

SeaTalk

spurcableconnectionbetweentheSeaTalk

bus

andtheEV2’sSeaTalk

connector.

3.9Warningsandcautions

Important:Beforeproceeding,ensurethatyouhaveread

andunderstoodthewarningsandcautionsprovidedinthe

Chapter1Importantinformationsectionofthisdocument.

ECI–100

3.10Generallocationrequirements

Importantconsiderationswhenchoosingasuitablelocationfor

yourproduct.

Thisproductissuitableformountingbelowdecks.

Theproductshouldbemountedwhereitwillbe:

•protectedfromphysicaldamageandexcessivevibration.

•wellventilatedandawayfromheatsources.

Whenchoosingalocationfortheproduct,considerthefollowing

pointstoensurereliableandtrouble-freeoperation:

•Access—theremustbesufcientspacetoenablecable

connectionstotheproduct,avoidingtightbendsinthecable.

•Diagnostics—theproductmustbemountedinalocation

wherethediagnosticsLEDiseasilyvisible.

Note:NotallproductsincludeadiagnosticsLED.Refer

totheChapter6Systemchecksandtroubleshootingfor

moreinformation.

•Electricalinterference—theproductshouldbemountedfar

enoughawayfromanyequipmentthatmaycauseinterference

suchasmotors,generatorsandradiotransmitters/receivers.

•Magneticcompass—refertotheCompasssafedistance

sectioninthisdocumentforadviceonmaintainingasuitable

distancebetweenthisproductandanycompassesonyour

vessel.

•Power—tokeepcablerunstoaminimum,theproductmust

belocatedascloseaspossibletothevessel’sdcpower

supply.

•Mountingsurface—ensuretheproductisadequately

supportedonasecuresurface.Refertotheweightinformation

providedintheTechnicalspecicationforthisproductand

ensurethattheintendedmountingsurfaceissuitablefor

bearingtheproductweight.DoNOTmountunitsorcutholes

inplaceswhichmaydamagethestructureofthevessel.

Compasssafedistance

Topreventpotentialinterferencewiththevessel'smagnetic

compasses,ensureanadequatedistanceismaintainedfrom

theproduct.

Whenchoosingasuitablelocationfortheproductyoushould

aimtomaintainthemaximumpossibledistancefromany

compasses.Typicallythisdistanceshouldbeatleast1m(3ft)

inalldirections.Howeverforsomesmallervesselsitmaynot

bepossibletolocatetheproductthisfarawayfromacompass.

Inthissituation,whenchoosingtheinstallationlocationforyour

product,ensurethatthecompassisnotaffectedbytheproduct

whenitisinapoweredstate.

3.11Productdimensions

109.2 mm (4.3 in)

30.2 mm (1.19 in)

21.35 mm (0.84 in)

100 mm (3.94 in)

D12972-1

Planningtheinstallation

Chapter4:Cablesandconnections

Chaptercontents

• 4.1 General cabling guidance

• 4.2 Connections overview

• 4.3 Power connection

• 4.4 Data and control connections

Cablesandconnections

4.1Generalcablingguidance

Cabletypesandlength

Itisimportanttousecablesoftheappropriatetypeandlength

•Unlessotherwisestateduseonlystandardcablesofthe

correcttype,suppliedbyRaymarine.

•Ensurethatanynon-Raymarinecablesareofthecorrect

qualityandgauge.Forexample,longerpowercablerunsmay

requirelargerwiregaugestominimizevoltagedropalongthe

run.

Routingcables

Cablesmustberoutedcorrectly,tomaximizeperformanceand

prolongcablelife.

•DoNOTbendcablesexcessively.Whereverpossible,ensure

aminimumbenddiameterof200mm(8in)/minimumbend

radiusof100mm(4in).

100 mm (4 in)

200 mm (8 in)

•Protectallcablesfromphysicaldamageandexposuretoheat.

Usetrunkingorconduitwherepossible.DoNOTruncables

throughbilgesordoorways,orclosetomovingorhotobjects.

•Securecablesinplaceusingtie-wrapsorlacingtwine.Coil

anyextracableandtieitoutoftheway.

•Whereacablepassesthroughanexposedbulkheador

deckhead,useasuitablewatertightfeed-through.

•DoNOTruncablesneartoenginesoruorescentlights.

Alwaysroutedatacablesasfarawayaspossiblefrom:

•otherequipmentandcables,

•highcurrentcarryingacanddcpowerlines,

•antennae.

Strainrelief

Ensureadequatestrainreliefisprovided.Protectconnectors

fromstrainandensuretheywillnotpulloutunderextremesea

conditions.

Circuitisolation

Appropriatecircuitisolationisrequiredforinstallationsusing

bothACandDCcurrent:

•Alwaysuseisolatingtransformersoraseparatepower-inverter

torunPC’s,processors,displaysandothersensitiveelectronic

instrumentsordevices.

•AlwaysuseanisolatingtransformerwithWeatherFAXaudio

cables.

•Alwaysuseanisolatedpowersupplywhenusinga3rdparty

audioamplier.

•AlwaysuseanRS232/NMEAconverterwithopticalisolation

onthesignallines.

•AlwaysmakesurethatPC’sorothersensitiveelectronic

deviceshaveadedicatedpowercircuit.

Cableshielding

Ensurethatalldatacablesareproperlyshieldedthatthe

cableshieldingisintact(e.g.hasn’tbeenscrapedoffbybeing

squeezedthroughatightarea).

4.2Connectionsoverview

Usethefollowinginformationtohelpyouidentifytheconnections

onyourproduct.

ConnectorConnectorConnectsto:Suitablecables

SeaTalk

using

thesuppliedspur

cable.

SeaTalk

spur

cables.Refer

toChapter10

Sparesand

accessories.

DeviceNet

EngineCANbus.Enginespecic

DeviceNet

adaptorcable.

RefertoChapter

10Sparesand

accessories.

EnsurethattheDeviceNetconnector’sdustcapisremoved

beforetryingtomakeconnections.

Makingconnections

Followthestepsbelowtoconnectthecable(s)toyourproduct.

1.Ensurethatthevessel'spowersupplyisswitchedoff.

2.Ensurethatthedevicebeingconnectedtotheunithas

beeninstalledinaccordancewiththeinstallationinstructions

suppliedwiththatdevice.

3.Ensuringcorrectorientation,pushthecableconnectorfully

ontothecorrespondingconnectorontheunit.

4.Turnthelockingcollarclockwisetosecurethecable.

ECI–100

4.3Powerconnection

Bothconnectionsneedpowertobesuppliedfromeachnetwork

i.e.TheSeaT alk

connectionispoweredbytheSeaT alk

backboneorSeatalk

deviceandtheengine(DeviceNet)

connectionispoweredfromtheengine’sCANbusnetwork.

TheinformationinthissectionrelatestopoweringtheSeaT alk

network.PowerwillalreadybeavailableonyourenginesCAN

bustopowertheDeviceNetconnection.

PleaserefertotheRaymarineSeaTalk

Referencemanual

(81300)forfurtherinformationonSeaTalk

networks.

Powercableextension

Theproductissuppliedwithapowercable,whichcanbe

extendedifrequired.

•Thepowercableforeachunitinyoursystemshouldberunas

aseparate,singlelengthof2-wirecablefromtheunittothe

vessel'sbatteryordistributionpanel.

•Raymarinerecommendsaminimumwiregaugeof18AWG

(0.82mm

)foranylengthofcableextension.

•Regardlessofthelengthofthecableextension,anycable

usedshouldbecapableofachievingaminimumvoltageat

theunitof10.8Vwithafullyatbatteryat11V.

Powerdistribution

Raymarinerecommendsthatallpowerconnectionsaremade

viaadistributionpanel.

•Allequipmentmustbepoweredfromabreakerorswitch,with

appropriatecircuitprotection.

•RefertotheBreakers,fusesandcircuitprotectionsectionfor

specicfuseandthermalbreakerratingsforthisproduct.

Breakers,fusesandcircuitprotection

Itisrecommendedthatyoutathermalbreakerorfuseatthe

distributionpanel.

Thermalbreakerrating

5A(ifonlyconnectingonedevice)

Note:Thesuitablefuseratingforthethermalbreakeris

dependentonthenumberofdevicesyouareconnecting.Ifin

doubtconsultanauthorizedRaymarinedealer.

Sharingabreaker

Wheremorethan1pieceofequipmentsharesabreakeryou

mustprovideprotectionfortheindividualcircuits.E.g.by

connectinganin-linefuseforeachpowercircuit.

D116 37-2

4 4

Positive(+)bar

Negative(-)bar

Circuitbreaker

4Fuse

Wherepossible,connectindividualitemsofequipmentto

individualcircuitbreakers.Wherethisisnotpossible,use

individualin-linefusestoprovidethenecessaryprotection.

Warning:Productgrounding

Beforeapplyingpowertothisproduct,ensureithas

beencorrectlygrounded,inaccordancewiththe

instructionsinthisguide.

Grounding—Dedicateddrainwire

Thepowercablesuppliedwiththisproductincludesadedicated

shield(drain)wireforconnectiontoavessel'sRFgroundpoint.

ItisimportantthataneffectiveRFgroundisconnectedtothe

system.Asinglegroundpointshouldbeusedforallequipment.

Theunitcanbegroundedbyconnectingtheshield(drain)wire

ofthepowercabletothevessel'sRFgroundpoint.Onvessels

withoutanRFgroundsystemtheshield(drain)wireshouldbe

connecteddirectlytothenegativebatteryterminal.

Thedcpowersystemshouldbeeither:

•Negativegrounded,withthenegativebatteryterminal

connectedtothevessel'sground.

•Floating,withneitherbatteryterminalconnectedtothe

vessel'sground

Warning:Positivegroundsystems

Donotconnectthisunittoasystemwhichhas

positivegrounding.

Cablesandconnections

4.4Dataandcontrolconnections

Theillustrationsbelowareexamplesofhowtheunitcanbe

connectedtoSeaT alk

andacompatibleengine’sCANbusto

enableenginedatatransmissionandsteeringcontrol.

Important:RaymarinedoesnotrecommendthattheECI-100

isusedonthesameCANbusasother3

partygateway

products.TheECI-100shouldbeusedtoreplaceexisting

gatewayproductsinyoursystem.

Note:Theillustrationsbelowareexamplesonly.EngineCAN

busconnectionsaremadeusingeithera‘Y’loomcable,CAN

bushuboratrailinglead.Theconnectionmethodwilldiffer

dependingonenginemanufacturer.TheSeaT alk

connection

remainsthesameregardlessofenginemanufacturer.

Fordetailsoncompatibleenginesandsteeringsystemsplease

refertotheSupportedengines/steeringsystemssection.

SingleengineCANbus‘Y’loomconnection

Dependingonenginemanufacturertheunitmaybeconnected

usinga‘Y’loomcableasshownbelow.Thisconnectionmethod

shouldnormallybeusedwhenaCANbushubisnotpresent.

12 V dc

D12976-2

3 5

SeaT alk

ItemDescription

SeaTalk

spurcableconnectionbetweentheSeaTalk

backboneandtheEV2’sSeaTalk

connector.

ECI-100unit

SeaTalk

networkpowersupply(12Vdc)

4YLoomcable

EV2—Evolution

autopilot

Engine-specicadaptorcable

EngineCANbus

SingleengineCANbusmulti-linkhubconnection

WhereavailabletheunitshouldbeconnectedusingtheCAN

bushub.

12 V dc

D12977-2

SeaT alk

ItemDescription

SeaTalk

spurcableconnectionbetweentheSeaTalk

backboneandtheEV2’sSeaTalk

connector.

ECI-100unit

SeaTalk

networkpowersupply(12Vdc)

ItemDescription

4EV2—Evolution

autopilot

Engine-specicadaptorcable

EngineCANbus

CANbushub

MultiCANbusconnection

OnvesselswhichhaveadedicatedCANbusforeachengine,1

unitisrequiredperCANbus.

12 V dc

D12978-1

2 3

6 2

Se aTalk

ItemDescription

Engine1CANbus

2Trailinglead

Engine-specicadaptorcable.

ECI–100

SeaTalk

networkpowersupply(12Vdc)

Engine2CANbus

Fordetailsonavailablenetworkhardwareandcablesreferto

Chapter10Sparesandaccessories.

Ifyourenginedataappearsinthewrongorderontheengine

datapagesofyourmultifunctiondisplayyoucancorrectthisby

runningtheengineidenticationwizard.

ECI–100

Chapter5:Mounting

Chaptercontents

• 5.1 Mounting the unit

Mounting

5.1Mountingtheunit

TheECIisdesignedtobesurfacemounted.

Beforemountingtheunitensurethatyouhave:

•Identiedtheroutesthatthecableswilltake.

D12973-1

1.Switchoffthevessel’spowersupply.

2.Checktheselectedlocationfortheunit,aclear,atareais

required,whichissafetohavescrewsttedto.

3.Positiontheconverteragainsttheselectedlocationandmark

thesurfacethroughtheconverter’smountingholes.

4.Usinganappropriatesizedrillbit,drill2holesatthemarked

locations.

5.Positiontheconvertersothatthemountingholesoftheunit

lineupwiththedrilledholesinthemountingsurface.

6.Usingthexingsprovidedsecuretheconvertertothe

mountingsurface.DoNOTovertightenthexings.

7.ConnecttheSeaTalk

spurcableandtheDeviceNetadaptor

cabletotheunit.

8.EnsuretheCANbusconnectoroftheDeviceNetadaptor

cableispluggedintotherelevantpointontheengine’sCAN

bus.

9.Switchthevessel’spowersupplybackonandchecksystem.

ECI–100

Page is loading ...

Raymarine eci-100 Installation Instructions Manual

Raymarine eci-100 Installation Instructions Manual

Raymarine eci-100 Installation Instructions Manual

Related papers

Other documents