Hunter Fan 21325 Owner's manual

Brand: Hunter Fan

Model: 21325

Type: Owner's manual

Hunter Fan 21325 is a stylish and functional ceiling fan that offers a range of features to enhance your home's comfort and style. With its powerful motor, it provides efficient airflow to keep you cool in the summer and warm in the winter. The fan's reversible motor allows you to change the direction of the airflow for optimal comfort. It also comes with a convenient remote control for easy operation from anywhere in the room. The Hunter Fan 21325 is a great choice for those looking for a reliable and stylish ceiling fan to improve their home's comfort and ambiance.

Type 2 ModelsType 2 ModelsType 2 Models

Form# 45037-01

20110606

For Your Records and

Warranty Assistance

For reference, also attach your receipt or a copy

of your receipt to the manual.

__________________________________________

Model Name

__________________________________________

Model No.

__________________________________________

Date Purchased

__________________________________________

Where Purchased

English Español

Owner’s Guide and Installation Manual

45037-01 • 06/06/11 • Hunter Fan Company

Table Of Contents

1 • Getting Ready......................6

2 • Installing the Hanger Bracket .......7

3 • Assembling and Hanging the Fan ...8

4 •Wiring the Fan......................10

5 • Installing the Canopy and Canopy Trim

Ring ..............................11

6 • Assembling the Blades..............12

7 • Installing the Switch Housing .......13

8 • Operating and Cleaning Your Ceiling

Fan ...............................15

9 • Troubleshooting....................16

Your new Hunter

ceiling fan is an addition to your home or oce that

will provide comfort and performance for many years. is installation

and operation manual gives you complete instructions for installing

and operating your fan.

We are proud of our work. We appreciate the opportunity to supply

you with the best ceiling fan available anywhere in the world.

Before installing your fan, for your records and warranty assistance,

record information from the carton and Hunter nameplate label

(located on the top of the fan motor housing).

Cautions and Warnings

• READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING

INSTALLATION. SAVE THESE INSTRUCTIONS.

• Use only Hunter replacement parts.

• To reduce the risk of personal injury, attach the fan directly to the

support structure of the building according to these instructions,

and use only the hardware supplied.

• To avoid possible electrical shock, before installing your fan,

disconnect the power by turning o the circuit breakers to the

outlet box and associated wall switch location. If you cannot lock

the circuit breakers in the o position, securely fasten a prominent

warning device, such as a tag, to the service panel.

• All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualied electrician.

• To reduce the risk of personal injury, do not bend the blade

attachment system when installing, balancing, or cleaning the fan.

Never insert foreign objects between rotating fan blades.

• To reduce the risk of re, electrical shock, or motor damage, do not

use a solid-state speed control with this fan. Use only Hunter speed

controls.

Welcome

45037-01 • 06/06/11 • Hunter Fan Company

Preparing the Fan Site

7’ Minimum

Blades to

Floor

8’ Minimum

Ceiling

Height

30” From

Wall or

Nearest

Obstruction

Step 1 - Choose the Fan Site

Proper ceiling fan location and attachment to the building

structure are essential for safety, reliable operation, maximum

eciency, and energy savings.

Choose a fan site where:

• No object can come in contact with the rotating fan blades during

normal operation.

• e fan blades are at least 7 feet above the oor and the ceiling is

at least 8 feet high.

• e fan blades have no obstructions to airow, such as walls or

posts, within 30 inches of the fan blade tips.

• e fan is directly below a joist or support brace that will hold the

outlet box and the full weight of the fan.

Checklist for Existing Fan Site

If you want to use an existing fan site, complete the following checklist to

determine if the site is acceptable and safe for your new Hunter fan. If you

cannot check o every item, prepare a new fan site as described on this

page.

Fan Support System

• Fan attaches directly to building structure.

• Fan support system will hold full weight of the fan and light kit.

Ceiling Hole

• e outlet box clearance hole is directly below the joist or support brace.

Outlet Box

• e outlet box is an UL-approved octagonal 4” x 1-1/2” outlet box (or as

specied by the support brace manufacturer).

• e outlet box is secured to the joist or support brace by wood screws

and washers through the inner holes of outlet box.

• e outer holes of the outlet box are aligned with joist or support brace.

• e bottom of the outlet box is recessed a minimum of 1/16” into

ceiling.

Wiring

• e electrical cable is secured to outlet box by an approved connector.

• Six inches of lead wires extend from outlet box.

If your existing fan site is suitable, skip ahead to Section 2 • Installing the

Ceiling Plate.

Suitable Existing Fan Site

Fan Support

System

Fan Support

System

Wiring

Outlet Box

45037-01 • 06/06/11 • Hunter Fan Company

Preparing the Fan Site (continued)

CAUTION: All wiring must be in

accordance with national and local

electrical codes and ANSI/NFPA 70. If

you are unfamiliar with wiring, use a

qualied electrician.

Steps 2 – 3

Step 4

Step 5

Step 2 - Cut the Ceiling Hole

2-1. Locate the site for the ceiling hole directly below the joist or support brace that

will hold the outlet box and fan.

2-2. Cut a 4” diameter hole through the drywall or plaster of the ceiling. You will use

the hole to install the support brace and outlet box.

Step 3 - Install a Support Brace, If Necessary

Determine if there is a ceiling joist directly above the ceiling hole. If the joist is there,

determine if it is positioned to allow you to recess the outlet box a minimum of

1/16” into the ceiling. If NOT, install a support brace as follows:

3-1. Attach a 2” x 4” support brace between two joists. Position it to allow you to

recess the bottom of the outlet box a minimum of 1/16” into the ceiling.

3-2. Check the support brace to ensure it will support the full weight of the fan and

light kit.

Step 4 - Install the Outlet Box

4-1. Obtain a UL-approved octagonal 4” x 1-1/2” outlet box, plus two #8 x 1-1/2”

wood screws and washers, available from any hardware store or electrical supply

house.

4-2. Orient the outlet box so that both the inner and outer holes in the box align

with the joist or support brace.

4-3. Drill pilot holes no larger than the minor diameter of the wood screws (5/64”)

through the inner holes of the outlet box.

4-4. Attach the outlet box directly to the support brace or joist with two #8 x 1-1/2”

wood screws and washers. e bottom of the outlet box must be recessed a

minimum of 1/16” into the ceiling.

Step 5 - Prepare the Wiring

5-1. Make sure the circuit breakers to the fan supply line leads and associated wall

switch location are turned o . If you cannot lock the circuit breakers in the

o position, securely fasten a prominent warning device, such as a tag, to the

service panel.

5-2. read the fan supply line through the outlet box so that the fan supply line

extends at least 6” beyond the box.

5-3. Attach the fan supply line to the outlet box with an approved connector,

available at any hardware store or electrical supply house.

5-4. Make certain the wiring meets all national and local standards and ANSI/NFPA

70.

You have now successfully prepared your ceiling fan site. For instructions to install

your ceiling fan, go to your fan manual and continue with Section 2 • Installing the

Ceiling Plate.

45037-01 • 06/06/11 • Hunter Fan Company

Installer’s Choice and Optional Accessories

Understanding Mounting and Installer’s Choice®

Hunter’s patented 3-position mounting system provides you maximum

installation exibility and ease. You can install your Hunter fan in one

of three ways, depending on ceiling height and your preference: Low

Prole, Standard, or Angled mounting. e steps in this manual include

instructions for all three Installer’s Choice mounting methods.

Considering Optional Accessories

Consider using Hunter’s optional accessories, including a wall-mounted

or remote speed control. To install and use the accessories, follow

the instructions included with each product. For quiet and optimum

performance of your Hunter fan, use only Hunter speed controls.

For ceilings higher than 8 feet, you can purchase

Hunter extension downrods. All Hunter fans use

sturdy 3/4” diameter pipe to assure stability and

wobble-free performance.

Standard Mounting hangs from the

ceiling by a downrod (included).

Angled Mounting recommended for a

vaulted or angled ceiling

Support Brace

Standard

Mounting

Style

Ceiling

Outlet Box

Support Brace

Ceiling

Outlet Box

Angled

Mounting

Style

Low Proﬁle Mounting ts close to the

ceiling, recommended for ceilings less

than 8 feet high

Support Brace

Low Prole

Mounting

Style

Ceiling

Outlet Box

CAUTION: To

reduce the risk of

personal injury, attach

the fan directly to the

support structure of

the building according

to these instructions,

and use only the

hardware supplied.

45037-01 • 06/06/11 • Hunter Fan Company

To install a ceiling fan, be sure you can do the following:

• Locate the ceiling joist or other suitable support in ceiling.

• Drill holes for and install wood screws.

• Identify and connect electrical wires.

• Lift 40 pounds.

If you need help installing the fan, your Hunter fan dealer can direct

you to a licensed installer or electrician.

Gathering the Tools

You will need the following tools for installing the fan:

• Electric drill with 9/64” bit

• Standard screwdriver (magnetic tip recommended)

• Phillips-head screwdriver (magnetic tip recommended)

• Wrench or pliers

• Ladder (height dependent upon installation site)

Checking Your Fan Parts

Carefully unpack your fan to avoid damage to the fan parts. Refer to

the included Parts Guide. Check for any shipping damage to the motor

or fan blades. If any parts are missing or damaged, contact your Hunter

dealer or call Hunter Technical Support Department at 888-830-1326.

Preparing the Fan Site

Before you begin installing the fan, follow all the instructions in

the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan

location and attachment to the building structure are essential for

safety, reliable operation, maximum eciency, and energy savings.

Installing Multiple Fans?

If you are installing more than

one fan, keep the fan blades and

blade irons (if applicable) in sets,

as they were shipped.

1 • Getting Ready

45037-01 • 06/06/11 • Hunter Fan Company

2-1. Drill two pilot holes into the wood support structure through the

outermost holes in the outlet box. e pilot holes should be 9/64”

in diameter.

Note: Your fan comes with four pre-installed neoprene noise

isolators.

2-2. read the lead wires from the outlet box down through the hole

in the middle of the hanger bracket.

2-3. Align the slotted holes in the hanger bracket with the pilot holes

you drilled in the wood support structure. For proper alignment

use slotted holes directly across from each other. If you are

installing the fan on an ANGLED ceiling, be sure to orient the

hanger bracket as shown in Illustration 2-3 (left or right view).

Note: e isolators should be ush against the ceiling.

2-4. Place a at washer on each of the two 3” screws and pass the

screws through the slotted holes in the hanger bracket into the

pilot holes you drilled.

Tighten the screws into the 9/64” pilot holes; do not use lubricants

on the screws. Do not over tighten.

Flat Washer

3” Screw

Steps 2-2 – 2-4

Hanger

Bracket

Isolator

Step 2-3 (Angled Ceiling Only)

Ceiling Peak Ceiling Peak

Large

Opening

Large

Opening

LEFT RIGHT

2 • Installing the Hanger Bracket

45037-01 • 06/06/11 • Hunter Fan Company

You can assemble your fan for standard or angled mounting as shown

in steps 3-1 – 3-3. For low proﬁle mounting (ceilings less than 8 feet

high), go to steps 3-6 – 3-9 on the next page.

3-1. To assemble fan to hang down from a at or angled ceiling, place

the canopy and canopy trim ring around the adapter so that they

rest on the fan assembly.

3-2. Feed the wires from the fan through the downrod.

Note: Make sure all the wires are on the same side of the metal

dowel pin inside the dowrod.

3-3. Loosen the square head setscrew on the adapter to install the pipe

and ball assembly. Note: When the pipe and ball assembly is fully

installed, 2-3 threads on the pipe will still be visible; this is normal.

Securely retighten the setscrew with a wrench or pliers.

CAUTION: e adapter has a special coating on the threads. Do

not remove this coating; the coating prevents the downrod from

unscrewing. Once assembled, do not remove the downrod.

WARNING: Do not carry or lift fan by canopy.

3-4. Raise the fan and place the ball into the hanger bracket.

3-5. Align the notch on the ball with the indent in the hanger bracket.

(Rotate the fan until you hear the notch pop into place.)

Go to 4 • Wiring the Fan.

WARNING: Fan may fall if not assembled as directed in these

installation instructions.

Steps 3-4 – 3-5

Indent

Steps 3-1 – 3-3

Downrod

Canopy

(with Washer)

Canopy

Trim

Ring

Setscrew

Adapter

3 • Assembling and Hanging the Fan

45037-01 • 06/06/11 • Hunter Fan Company

3 • Assembling and Hanging the Fan (Low Profile Only)

You can assemble your fan for standard or angled mounting as shown

in steps 3-1 – 3-3 on the previous page. For low proﬁle mounting

(ceilings less than 8 feet high), see steps 3-6 – 3-10 on this page.

3-6. Remove the screws from the hanger ball bracket.

3-7. Place the low prole washer from the parts sack into the canopy.

3-8. Place the canopy trim ring and canopy with washer on top of the

fan assembly.

3-9. Align the screw holes in the washer with the holes in the adapter.

Assemble securely with three #8-32 x 3/4” screws.

3-10. Raise the fan and place the hook on the hanger bracket through

the round hole in the rim of the canopy.

WARNING: Fan may fall if not assembled as directed in these

installation instructions.

Step 3-10

Step 3-7 (Detail)

Low Prole Washer

(Not Actual Size)

Steps 3-8 – 3-9

Low Prole Washer

Canopy

Trim Ring

Adapter

#8-32 x 3/4” Screw

Step 3-6

45037-01 • 06/06/11 • Hunter Fan Company

All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualiﬁed electrician.

Wall switches are not included. Select an acceptable general-use switch

in accordance with national and local electrical codes.

4-1. Before attempting installation, make sure the power is still o.

4-2. To connect the wires, hold the bare metal leads together and place

a wire connector over them, then twist clockwise until tight. For

all these connections use the wire connectors provided.

4-3. Connect the bare or green ground wire (grounded) from the

ceiling to the green ground wire (grounded) from the ceiling plate

and the green ground wire from the fan.

4-4. Connect the white wire (ungrounded) from the ceiling to the

white wire (ungrounded) from the fan.

4-5. Connect the remaining wires as follows:

Dual Switch Wiring:

• e black wire (ungrounded) from the ceiling to the black wire

(ungrounded) from the fan

• e black/white wire (ungrounded) from the fan to the wire

(ungrounded) for the wall switch

Single Switch Wiring:

• e black wire (ungrounded) from the ceiling to the black

(ungrounded) and the black/white wire (ungrounded) from

the fan

CAUTION: Be sure no bare wire or wire strands are visible after

making connections.

4-6. Turn the wire connectors upward and push them carefully back

through the ceiling plate into the outlet box.

4-7. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the

outlet box.

Wire

Connector

4 •Wiring the Fan

45037-01 • 06/06/11 • Hunter Fan Company

5-1. Partially install two canopy screws (about 2 full turns) in the

hanger bracket.

5-2. Raise the canopy over the hanger bracket. Align partially installed

screws with key slots in canopy.

5-3. Twist canopy clockwise to secure.

5-4. Install third & fourth canopy screw in round hole on canopy.

Securely tighten all four screws.

5-5. Using both hands, push the canopy trim ring up to the top of the

canopy.

5-6. Twist canopy trim ring clockwise to secure the canopy.

Should you need to remove the canopy

trim ring, follow these steps:

1. Twist canopy trim ring counter

clockwise until it releases from

canopy.

Steps 5-1 – 5-2

Canopy Trim

Ring

Canopy

Hanger Bracket

Step 5-3

Canopy

Screw

Step 5-4

Step 5-5

5 • Installing the Canopy and Canopy Trim Ring

45037-01 • 06/06/11 • Hunter Fan Company

6 • Assembling the Blades

Hunter fans use several styles of fan blade irons (brackets that hold the

blade to the fan).

6-1. Your fan may include blade grommets. If your fan has grommets,

insert them by hand into the holes on the blades.

6-2. Attach each blade to a blade iron using three blade assembly

screws. If you used grommets, the blades may appear slightly loose

after screws are tightened. is is normal.

6-3. Remove the blade mounting screws and metal shipping ring from

the bottom of the motor. Note: Some blade mounting screws are

installed in the motor to secure the metal shipping ring.

6-4. For each blade, insert one blade mounting screw through the

blade iron, and attach lightly to the fan. Insert the second blade

mounting screw, then securely tighten both mounting screws.

Step 6-1 (Detail)

Use with grommet

Use without grommet

Grommet

Steps 6-1 – 6-2

Step 6-4

Blade

Mounting

Screw

Step 6-3 (Detail)

Blade Assembly

Screws

45037-01 • 06/06/11 • Hunter Fan Company

7-1. To attach the upper switch housing, partially install two housing

assembly screws into the switch housing mounting plate.

7-2. Feed the upper plug connector through the center opening of the

housing.

7-3. Align the keyhole slots in the housing with the housing assembly

screws.

7-4. Turn the housing counterclockwise until the housing assembly

screws are rmly situated in the narrow end of the keyhole slots.

Install the remaining screw into the housing. Tighten all three

screws rmly.

CAUTION: Make sure the upper switch housing is securely attached

to the switch housing mounting plate. Failure to properly attach and

tighten all three assembly screws could result in the switch housing

xture falling.

Steps 7-1 – 7-4

Housing

Assembly

Screw

Upper

Switch

Housing

Assembly

Screw

Lower

Switch

Housing

Plug

Connector

7 • Installing the Switch Housing

45037-01 • 06/06/11 • Hunter Fan Company

7-5. To attach the lower switch housing, connect the upper

plug connector from the motor to the lower plug

connector in the lower switch housing assembly.

Note: Both plug connectors are polarized and will only t

together one way. Make sure the connectors are properly

aligned before connecting them. Incorrect connection

could cause improper operation and damage to the

product.

7-6. Place the lower switch housing assembly over the upper

switch housing. Align the side screw holes in the upper

and lower switch housings. Attach the lower switch

housing to the upper switch housing.

7-7. Install a shade onto the light bulb socket.

7-8. Screw the locking ring onto the light bulb socket.

7-9. Repeat the above steps for the remaining light bulb

sockets.

7-10. Install three 14W CFL light bulbs

Lower Switch

Housing

Assembly Screw

Plug

Connector

Detail

Steps 7-5 – 7-6

Shade

Plug

Connector

7 • Completing Your Installation With a Light Fixture

45037-01 • 06/06/11 • Hunter Fan Company

8 • Operating and Cleaning Your Ceiling Fan

In warm weather, use

downward air ow pattern

In cold weather, use upward

air ow pattern

8-1. Turn on electrical power to the fan.

8-2. e fan pull chain controls power to the fan. e pull chain has

four settings in sequence: High, Medium, Low and O.

• Pull the chain slowly to change settings.

• Release slowly to prevent the chain from recoiling into the

blades.

• e chain uses a breakaway connector that separates if the

chain is jerked. If this happens, simply reinsert the chain into

the connector.

8-3. e light pull chain controls power to the light. e pull chain has

two settings: On and O.

8-4. Ceiling fans work best by blowing air downward (counterclockwise

blade rotation) in warm weather to cool the room with a direct

breeze. In winter, having the fan draw air upward (clockwise blade

rotation) will distribute the warmer air trapped at the ceiling

around the room without causing a draft.

8-5. e blades on this fan have been treated with Hunter’s Dust

Armor protection, making the blades less likely to attract dust and

dirt. Use a dry or slightly damp lint free cloth to clean the blades.

Do not use a furniture polish or any other cleaners that leave any

residue, as they will damage the protective Dust Armor on the

blades.

8-6. For cleaning nishes, use a soft brush or lint-free cloth to prevent

scratching. A vacuum cleaner brush nozzle can remove heavier

dust. Remove surface smudges or accumulated dirt and dust

using a mild detergent and a slightly dampened cloth. You may

use an artistic

agent, but

never abrasive

cleaning agents

as they will

damage the

nish.

To Change Airﬂow Direction

Turn the fan o and let it come to a complete

stop. Slide the reversing switch on the fan to the

opposite position. Restart fan.

Reversing

Switch

8 • Operating and Cleaning Your Ceiling Fan

45037-01 • 06/06/11 • Hunter Fan Company

Problem: Nothing happens; fan does not move

1. Turn power on, replace fuse, or reset breaker.

2. Loosen canopy, check all connections according to the wiring the

fan section.

3. Check the plug connection in the switch housing.

4. Push motor reversing switch rmly left or right to ensure that the

switch is engaged.

5. Pull the pull chain to ensure it is on.

6. Remove the shipping bumpers.

Problem: Noisy operation

1. Tighten the blade assembly screws and blade iron armature screws

until snug.

2. Check to see if the blade is cracked. If so, replace all the blades.

Problem: Excessive wobbling

1. If your fan wobbles when operating, use the enclosed balancing kit

and instructions to balance the fan.

2. Tighten all blade iron screws.

3. Turn power o, support fan very carefully, and check that the

hanger ball is properly seated.

If you need parts or service assistance, please call

888-830-1326 (In Canada, call 866-268-1936) or

visit us at our Web site at

http://www.hunterfan.com.

Hunter Fan Company

7130 Goodlett Farms Parkway #400

Memphis, Tennessee 38016

9 • Troubleshooting

Hunter Fan 21325 Owner's manual

Hunter Fan 21325 Owner's manual

Hunter Fan 21325 Owner's manual

Related papers

Other documents