Ikelite 200DL Underwater Housing for Sony Alpha A7 II, A7R II, A7S II Mirrorless Cameras User manual

Brand: Ikelite

Model: 200DL Underwater Housing for Sony Alpha A7 II, A7R II, A7S II Mirrorless Cameras

Category: Underwater camera housings

Type: User manual

Ikelite 200DL Underwater Housing for Sony Alpha A7 II, A7R II, A7S II Mirrorless Cameras allows you to take professional-grade photos and videos underwater with your Sony camera. With a depth rating of 200 feet, this durable housing protects your camera from water, dust, and shock while providing access to all essential camera functions through mechanical controls. It features a zoom gear retainer for easy lens changes and a top accessory mount for attaching additional accessories like lighting or a focus light.

Product Registration

Please register your product within 15 days of purchase. Our product

registration database is the quickest way for us to contact you in the

event of a product update.

To register, send a photo of the above registration label to us via

[email protected] along with your name, address, and phone

number.

200DL Underwater Housing for Sony Alpha A7 II,

A7R II, A7S II

Product # 71472

Introduction

Thank you for your purchase of Ikelite products.

Our primary focus is to provide quality, professional grade products

for use in and under water. Our products are designed, manufactured,

and distributed from our sole facility in Indianapolis, USA where we

started in 1962.

We are available if you have any questions or want photo advice.

Send us an email 24 hours a day to [email protected]. We strive to

reply within 1 business day.

An electronic version of this instruction manual is available for

download via the product page on our website:

https://www.ikelite.com

In the Box

• Housing

• Main O-ring # 0132.59 (installed)

• Port O-ring # 0132.45 (installed)

• Zoom Gear Retainer # 0072.42 (installed)

• Port Hole Cover # 0200.92 (installed)

• Waterproof Bulkhead Cap # 9104.7 (installed)

• Base with Left-Hand Quick Release Handle (installed)

• Hardware Set for Base with Handle # 9523.23 (installed)

• Tool for Zoom Gear Retainer # 0945.06

• .050” Hex Key # 0945.11

• 1/16” Hex Key # 0945.16

• Silicone Lubricant # 0184.1

Important Notices

» This housing requires a compatible DL lens port for waterproof

operation (sold separately). The housing is not waterproof

without a DL lens port attached.

» A bulkhead cap or sync cord must be attached to the housing

bulkhead for waterproof operation. Never submerge the

housing in water without either a sync cord or bulkhead cap

attached.

» Do not pull the shutter trigger without a camera installed. You

may accidentally detach or damage the control spring.

» Never leave a housing in a rinse tank, even if it is the only

system in the tank. Accidental damage may occur when the

user walks away from a housing while it is in the rinse tank.

» Do not use alcohol, cleaning agents, spray lubricants, Rain-X,

or other solvents on the housing or lens port. Use of an

incompatible chemical compound can damage the plastic and

o-rings, and may result in leaking.

» If you will be using the system in strong surf it is

recommended to draw a vacuum on the housing using the

optional vacuum pump (sold separately).

Contents

Product Registration 1

Introduction 2

In the Box 2

Important Notices 3

Getting to Know Your Housing 6

Base with Quick Release Handle 9

Accessory Port 9

Top Accessory Mount 10

Vacuum Valve 10

Trigger Extensions 10

Setting Up Your Camera 11

Pre-Installation Checklist 11

Camera Settings 11

Exposure Settings 11

Back Button Focus 12

Power Save 12

Setting Up Your Housing 13

Removing the Port Hole Cover 13

Installing a Zoom or Focus Gear 14

Opening the Housing 15

Installing the Camera 16

Attaching the Hotshoe 17

Closing the Housing 17

Turning the Camera On/Off 18

Attaching a Lens Port 19

Installing the Lens and Port 19

Setting Up An External Strobe 21

About Sync Cords 21

Attaching a Sync Cord or TTL Converter 22

Getting in the Water 23

Final Check 23

Entering the Water 24

Shooting Underwater 24

Learning about Underwater Photography 25

Maintaining Your Housing 25

Post-Dive 25

Lens Port 26

Storage 26

Servicing Recommendations 27

Lubricating Controls 27

Lubricating Push Buttons 28

Lubricating Control Shafts 28

Troubleshooting 30

Spare Parts 32

Limited Warranty 33

Service and Repairs 33

Getting to Know Your Housing

Shutter

Bulkhead

with cap

Port hole cover

Front dial

Tray mounts

Vacuum valve

Lens

release

Zoom /

Focus

Zoom gear

retainer

ISO

SONY A7II A7RII A7SII / 200FT

MADE IN USA

START/

STOP

DISP

Playback

C4 / Delete

Viewnder

MOVIE

AF/MF/

AEL button

O-ring

ISO

SONY A7II A7RII A7SII / 200FT

MADE IN USA

START/

STOP

DISP

Set

Left / drive

mode

Down

C3 / Enlarge

Up / DISP

Right / ISO

Bulkhead

without cap

Top mount

Power

Port mount

recess

Port mount

Exposure

compensation

C2 (custom 2)

ModeLid snap hook

Lid snap

Front o-ring

Accessory

port

C1 (custom 1)

Base with Quick Release Handle

The hard anodized aluminum base plate attaches to your housing with

the two 1/4” nylon washers and 1/4-20 x 3/8” screws.

It is recommended to remove your base with quick release handle and

thoroughly rinse the tray, housing, and hardware periodically.

A central 1/4-20 threaded hole allows attachment of the base plate to

a standard tripod.

The base features additional mounting locations for attachment to a

variety of Ikelite housings (hardware not included).

Accessory Port

This housing features one spare accessory port which may be used

for the attachment of optional accessories. This port accepts ttings

designed for a 1/2” through or 1/2-20 threaded hole. Visit ikelite.com

for an updated list of compatible products.

» Do not remove or loosen the accessory port plug unless you

are installing a compatible accessory.

Tripod mount

Top Accessory Mount

The housing features a 1/4-20 threaded top mount. Ball and ex type

mounts are available for the attachment of a GoPro camera, focus

light, or other lightweight accessories.

Vacuum Valve

Your housing features a valve to check for leaks before entering the

water. Use of the vacuum valve requires a pump, sold separately.

Valve lock

Plug

» DO NOT remove vacuum valve plug unless you are plugging in

a vacuum pump.

» DO NOT submerge the housing without the plug installed. The

housing will not be waterproof without the plug installed.

Trigger Extensions

The shutter and AF/MF/AEL levers may be extended to be closer

to your hands when using the optional Right-Hand Quick Release

Handle # 4077.02. This requires the Trigger Extension # 4077.93 (one

per control).

Trigger extensions and right-hand quick release handle are sold

separately.

Setting Up Your Camera

Pre-Installation Checklist

1. Insert a fully charged camera battery.

2. Insert a properly formatted memory card.

3. Remove lens cap and any attached lanyard or neck strap.

Camera Settings

• Set Eye-Start AF to “Off.”

• Set FINDER/MONITOR to “Monitor.”

• Set Release button to use dial to “Yes”. This allows adjustments

that are normally made by holding a button and rotating a command

dial to be made instead by rotating the command dial after the

button is released. Refer to your camera’s instruction manual for

more information.

• Set Flash mode to “Fill ash” when using an external strobe.

“Rear-curtain sync” may be used with compatible TTL converters.

• Set Red Eye Reduction to “Off” when using an external strobe.

• Set AF Illuminator to “Off” when using an external strobe.

• Set Silent Shooting Mode to “Off” when using an external strobe

(A7R II only).

Exposure Settings

Refer to the Cheat Sheets in the Photo School section of our website

for recommendations on exposure settings for a wide variety of

shooting situations:

https://www.ikelite.com/blogs/cheat-sheets

Back Button Focus

Back button focus takes some adjustment to get used to but can be

very valuable in a variety of shooting scenarios.

Use the camera’s custom settings menu to set Pre-AF to “Off.” Set

AF w/Shutter to “Off.” In the custom key settings, set AEL button to

“AF-ON,” which initiates autofocus. Set AF/MF button to “AF/MF Cntrl

Toggle.”

The AEL button is conveniently accessed by a thumb lever on the side

of the housing. Instead of half-pressing the shutter to obtain focus and

lock focus, press AEL.

For super macro photography, you can use this technique instead of a

manual focus gear. Press AEL to lock focus at the minimum focusing

distance of your lens. Then move slightly in or out until the subject is

in focus.

Other focus functions like Focus Mode and Focus Area may be

assigned to the custom buttons on the camera for easy access.

Power Save

The camera’s power save function allows you to extend battery life

signicantly and yet always be ready for the next shot.

Instead of turning the camera off and on to conserve energy, the

camera will automatically sleep when not active. To wake the camera,

simply press the shutter button to instantly return to full power.

Use the camera’s setup menu to set Pwr Save Start Time to 1-5

minutes depending on your average period of time between active

shooting intervals.

Setting Up Your Housing

Removing the Port Hole Cover

1. Align the zoom gear retainer tool with the notches in the zoom

gear retainer.

Tool

Retainer

Port mount

Port hole

cover

2. Rotate the removal tool counter-clockwise until the retainer is free

from the lens port mount.

3. Remove the port hole cover from the housing.

Installing a Zoom or Focus Gear

1. Place the zoom or focus gear (sold separately) into the lens port

mount opening with the gear teeth toward the inside of the

housing.

Zoom or

focus gear

Retainer

2. Place the gear retainer into the opening around the gear.

3. Tighten the retainer by turning clockwise with the tool until snug.

Do not overtighten.

Opening the Housing

1. Push the lid snap lock forward and lift the curved end away from

the housing.

Lock

2. Lid snaps are designed to provide enough force to compress the

o-ring for a proper seal. Keep rm pressure against the lid snap

while lifting it away.

3. Repeat with remaining lid snaps.

4. Remove the housing back.

Installing the Camera

1. Remove any lanyard or neck strap which may be attached to the

camera.

2. Check to see whether the camera’s lens will t through the port

opening of the housing. If not, the lens will need to be removed

from the camera body and re-attached after the camera body is

installed in the housing.

3. Remove the camera mount plate from the housing.

4. Line the mount screw up with the camera’s tripod socket. Use a at

screwdriver to tighten the mount plate to the camera.

LENS

Mount screw

1/4-20 tripod

mount

Camera

tripod socket

5. Pull out on the housing control knobs to move the controls out of

the way.

6. Insert the mount plate into the slot on the inside bottom of the

housing. Push the camera all of the way forward until it stops.

7. Push housing control knobs in and check orientation with the

camera.

» The camera may be attached to a tripod using the 1/4-20

threaded mounting hole on the bottom of the mount plate.

Attaching the Hotshoe

1. Orient the hotshoe with the arrow on top pointing towards the front

of the camera.

2. Slide the housing hotshoe into camera’s hotshoe mount until it

stops.

» The hotshoe must be all the way forward in the camera mount

for proper ash operation.

Closing the Housing

1. Make sure the o-ring is clean and in its proper location on the back

of the housing. The rear housing o-ring does not require lubricant

to make a seal.

2. Place the back onto the housing front.

3. Make sure no controls or wires are interfering with the o-ring or the

back of the housing.

4. Place each lid snap into the corresponding hook on the housing

back.

Housing

hotshoe

Camera

hotshoe

mount

5. Push the lid snaps towards the housing until they are at against

the housing and the lock has engaged. Close opposing lid snaps at

the same time.

6. Check the o-ring seal. The o-ring should form a uniform, solid line

visible through the back of the housing.

7. Check control functions.

8. Attach a lens to the camera body. If using a zoom gear with clamp,

refer to the zoom gear instructions for information on interfacing

the clamp with the zoom gear.

Turning the Camera On/Off

1. The housing on/off lever acts like your nger pressing against

the side of the camera’s control. Rotate the knob to operate the

control. The control will only operate in one direction depending on

which side of the camera’s control the lever is sitting on.

2. To reverse directions, lift and rotate the knob to move the lever to

the other side of the control.

» If the control knob stops and the desired effect hasn’t

occurred, repeat step 2 to reverse directions.

Attaching a Lens Port

Refer to the appropriate lens port chart to nd compatible lens ports

for a wide variety of popular wide angle, zoom, and macro lenses.

Choose a dome port for wide angle and zoom lenses. Larger diameter

domes are better for split shots (half-in, half-out of the water) and

provide sharper images.

Choose a at port for macro lenses. Flat ports magnify the subject

underwater. Flat ports are not recommended for wide angle or zoom

lenses due to their limited eld of view and risk of vignetting (dark

shadows around the edges of the image).

» This housing requires a compatible DL lens port for waterproof

operation (sold separately). The housing is not waterproof

without a DL lens port attached.

Installing the Lens and Port

1. Attach the lens to the camera. If using a zoom/focus gear set that

requires a clamp, make sure the clamp slots are aligned with the

gear tabs. Test the function before attaching the port.

2. Check that the port sealing surface is clean and free of debris.

3. Apply a very thin, even layer of lubricant to the exposed portion of

the front o-ring and to the lens port sealing surface. Avoid dry spots

or uneven build-up of lubricant.

4. Align the port thumbscrews with the recesses in the housing’s port

mount.

5. Press the port rmly towards the housing until the base of the

port is ush with the housing’s port mount. If there is resistance,

remove the port and re-check that the thumbscrews are loosened

and the o-ring is properly lubricated.

Recess

Thumbscrew

RecessRecess

Thumbscrew

Page is loading ...

Ikelite 200DL Underwater Housing for Sony Alpha A7 II, A7R II, A7S II Mirrorless Cameras User manual

Brand: Ikelite

Model: 200DL Underwater Housing for Sony Alpha A7 II, A7R II, A7S II Mirrorless Cameras

Category: Underwater camera housings

Type: User manual

Download PDF

report

Ikelite 200DL Underwater Housing for Sony Alpha A7 II, A7R II, A7S II Mirrorless Cameras User manual

Ikelite 200DL Underwater Housing for Sony Alpha A7 II, A7R II, A7S II Mirrorless Cameras User manual

Related papers

Other documents