Mitsubishi Electronics FX2NC User manual

D/UL

HARDWARE MANUAL

FX

2NC

(D/UL) SERIES PROGRAMMABLE CONTROLLERS

FX2NC Series Programmable Controllers

Foreword

• This manual contains text, diagrams and explanations which will guide the reader in the

correct installation and operation of the FX

2NC

and should be read and understood before

attempting to install or use the unit.

• If in doubt at any stage during the installation of the FX

2NC

always consult a professional

electrical engineer who is qualified and trained to the local and national standards. If in

doubt about the operation or use of the FX

2NC

please consult the nearest Mitsubishi Elec-

tric distributor.

• This manual is subject to change without notice.

i

FX

2NC

(D/UL) Series Programmable

Controllers

Hardware Manual

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent

licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial

property rights which may occur as a result of using the contents noted in this manual.

FX

2NC

Series Programmable Controllers

Manual number : JY992D87201

Manual revision : F

Date : June 2010

FX2NC Series Programmable Controllers

ii

Guidelines for the safety of the user and protection of the FX

2NC

.

This manual provides information for the installation and use of the FX

2NC

. The manual has

been written to be used by trained and competent personnel. The definition of such a person

or persons is as follows;

a) Any engineer who is responsible for the planning, design and construction of automatic

equipment using the product associated with this manual should be of a competent

nature, (trained and qualified to the local and national standards required to fulfill that

role). These engineers should be fully aware of all aspects of safety with regards to auto-

mated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and qual-

ified to the local and national standards required to fulfill that job. These engineers

should also be trained in the use and maintenance of the completed product. This

includes being completely familiar with all associated documentation for the said product.

All maintenance should be carried out in accordance with established safety practices.

c) All operators of the completed product should be trained to use that product in a safe and

co-ordinated manner in compliance to established safety practices. The operators should

also be familiar with documentation which is connected with the actual operation of the

completed equipment.

Note :

The term ‘completed equipment’ refers to a third party constructed device which con-

tains or uses the product associated with this manual.

FX2NC Series Programmable Controllers

iii

Note’s on the symbology used in this manual

At various times through out this manual certain symbols will be used to highlight points of

information which are intended to ensure the users personal safety and protect the integrity of

the equipment. Whenever any of the following symbols are encountered, its associated note

must be read and understood. Each of the symbols used will now be listed with a brief descrip-

tion of its meaning.

Hardware warnings

Software warning

1) Indicates that the identified danger

WILL

cause physical and property damage.

2) Indicates that the identified danger could

POSSIBLY

cause physical and property damage.

3) Indicates a point of further interest or further explanation.

4) Indicates special care must be taken when using this element of software.

5) Indicates a special point which the user of the associate software element should be aware

of.

6) Indicates a point of interest or further explanation.

FX2NC Series Programmable Controllers

iv

• Under no circumstances will Mitsubishi Electric be liable responsible for any consequential

damage that may arise as a result of the installation or use of this equipment.

• All examples and diagrams shown in this manual are intended only as an aid to

understanding the text, not to guarantee operation. Mitsubishi Electric will accept no

responsibility for actual use of the product based on these illustrative examples.

• Please contact a Mitsubishi Electric distributor for more information concerning applications

in life critical situations or high reliability.

Registration

•Microsoft

®

and Windows

®

are either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

• The company name and the product name to be described in this manual are the registered

trademarks or trademarks of each company.

FX2NC Series Programmable Controllers

v

Contents.

Guideline.............................................................................................................................ii

1. Introduction .........................................................................................1-1

1.1 Unit accessories............................................................................................... 1-9

1.2 World Spec. ..................................................................................................... 1-9

1.3 Model name ................................................................................................... 1-10

1.4 Serial numbers............................................................................................... 1-11

1.5 Configuration.................................................................................................. 1-12

1.5.1 Summary ........................................................................................................... 1-14

1.5.2 Current consumption and input/output points.................................................... 1-16

1.5.3 Rules ................................................................................................................. 1-20

1.5.4 System configuration example .......................................................................... 1-23

1.5.5 Quick judgment ................................................................................................. 1-26

2. Terminal layouts..................................................................................2-1

2.1 Main units......................................................................................................... 2-1

2.2 FX

2NC

Extension blocks ................................................................................. 2-3

2.3 FX

2N

and FX

0N

Extension blocks ................................................................... 2-4

vi

Contents.FX2NC Series Programmable Controllers

3. Installation notes .................................................................................3-1

3.1 Product outline................................................................................................. 3-2

3.2 FX

2NC

RUN/STOP Control .............................................................................. 3-4

3.3 General specifications...................................................................................... 3-6

3.4 PC mounting arrangements............................................................................. 3-7

3.5 Connection of extension blocks to main unit.................................................... 3-9

3.6 DIN rail mounting ............................................................................................. 3-9

3.7 Direct mounting ............................................................................................. 3-10

3.8 Extension cable installation............................................................................ 3-14

3.9 General notes ................................................................................................ 3-15

3.10 Memory Board installation ............................................................................. 3-16

3.11 Wiring techniques .......................................................................................... 3-17

3.12 Termination of connector style I/O ................................................................. 3-18

3.13 Termination of screw terminals ...................................................................... 3-19

3.14 Termination of connector style I/O cables...................................................... 3-20

4. Power supply.......................................................................................4-1

4.1 Power supply cautions ..................................................................................... 4-5

4.2 Earthing / Grounding........................................................................................ 4-6

FX2NC Series Programmable Controllers

vii

Contents.

5. Inputs ..................................................................................................5-1

5.1 24V DC input specifications............................................................................. 5-1

5.1.1 Typical wiring....................................................................................................... 5-2

5.1.2 Input circuit connection........................................................................................ 5-4

5.1.3 Diodes and inputs connected in series;............................................................... 5-6

5.1.4 Resistors and inputs connected in parallel;......................................................... 5-7

5.2 AC110V input Extension block......................................................................... 5-8

5.2.1 Input circuit connection........................................................................................ 5-8

5.2.2 Programming caution .......................................................................................... 5-9

6. Outputs ...............................................................................................6-1

6.1 Transistor output specification ......................................................................... 6-1

6.1.1 Response times................................................................................................... 6-2

6.1.2 Output circuit configuration.................................................................................. 6-3

6.1.3 Transistor output example ................................................................................. 6-4

6.2 Relay output specification ................................................................................ 6-6

6.2.1 Product life of relay contacts ............................................................................... 6-7

6.2.2 Output circuit configuration.................................................................................. 6-9

6.2.3 Relay output example........................................................................................ 6-11

6.3 Triac (SSR) output specifications................................................................... 6-13

6.3.1 In-rush currents ................................................................................................. 6-14

6.3.2 Output circuit configuration................................................................................ 6-15

6.3.3 Triac output example......................................................................................... 6-17

6.4 Applying safe loads........................................................................................ 6-17

viii

Contents.FX2NC Series Programmable Controllers

7. Diagnostics..........................................................................................7-1

7.1 Preliminary checks........................................................................................... 7-1

7.2 Basic diagnostics ............................................................................................. 7-2

7.2.1 BATT LED ON..................................................................................................... 7-2

7.2.2 ERROR LED flashes (PROGRAM ERROR) ....................................................... 7-2

7.2.3 ERROR LED ON (CPU ERROR) ........................................................................ 7-3

7.3 Common errors................................................................................................ 7-4

7.4 Writing of program and program check [power ON and PLC stopped]............ 7-5

7.5 Replacing the battery....................................................................................... 7-6

7.6 Maintenance .................................................................................................... 7-8

7.7 Error flags ON indicates error. ......................................................................... 7-9

7.8 Error registers ................................................................................................ 7-11

7.9 Error codes .................................................................................................... 7-13

7.10 Instruction list .................................................................................................7-14

8. Discontinued model.............................................................................8-1

9. Appendix .............................................................................................9-1

9.1 Precautions for Battery Transportation ............................................................ 9-1

9.1.1 Regulated FX

2NC

Series products...................................................................... 9-1

9.1.2 Transport guidelines............................................................................................ 9-1

9.2 Handling of Batteries and Devices with Built-in Batteries in

EU Member States........................................................................................... 9-2

9.2.1 Disposal precautions........................................................................................... 9-2

9.2.2 Exportation precautions....................................................................................... 9-3

9.2.3 Regulated FX

2NC

Series products...................................................................... 9-4

1 INTRODUCTION

2 TERMINAL LAYOUTS

3 INSTALLATION NOTES

4 POWER SUPPLY

5 INPUTS

6OUTPUTS

7 DIAGNOSTICS

8 DISCONTINUED MODEL

9 APPENDIX

FX2NC Series Programmable Controllers Introduction 1.

Introduction 1.

1-1

1. Introduction

This manual covers the hardware installation instructions for the following programmable con-

troller (PC) product ranges;

-FX

2NC

main units.

-FX

2NC

extension blocks and special function blocks

Table 1.1 : Main units

MODEL

INPUT OUTPUT

POWER

SUPPLY

DIMENSIONS

mm (inches)

MASS

kg (lbs)

QTY TYPE QTY TYPE

W H D

FX

2NC

-16MT-D/UL 8

24V DC

Sink

8

Transistor

(Sink)

24V DC

+20%

-15%

Ripple

Vol tage

(p-p)

5% or less

35

(1.4)

90

(3.5)

87

(3.4)

0.2

(0.44)

FX

2NC

-32MT-D/UL 16 16

FX

2NC

-64MT-D/UL 32 32

60

(2.4)

0.35

(0.77)

FX

2NC

-96MT-D/UL 48 48

86

(3.4)

0.45

(0.99)

FX2NC Series Programmable Controllers

FX2NC Series Programmable Controllers Introduction 1.

1-2

Figure 1.1 :Main unit dimensions

RUN

STOP

POWER

RUN

BATT

ERROR

Y0

Y2

Y3

Y4

Y5

Y6

Y10

Y11

Y12

Y13

Y14

Y1

Y15

Y16

Y17

X16

X17

X0

X2

X3

X4

X5

X6

X10

X11

X12

X13

X14

X1

X14X14

X15

X7 Y7

74(2.91)

87(3.43)

13

(0.5)

90(3.54)

35(1.38)

FX

2NC

-32M

FX

2NC

-16M

FX

2NC

-64M

FX

2NC

-96M

60(2.36)

86(3.39)

(0.51)

DIN Rail: 35mm

(1.38)

Power

supply

cable

UNITS: mm (inches)

FX2NC Series Programmable Controllers Introduction 1.

1-3

Table 1.2 : Extension blocks

MODEL

INPUT OUTPUT

DIMENSIONS

mm (inches)

MASS

kg (lbs)

QTY TYPE QTY DEVICE TYPE

W H D

FX

2NC

-16EX-D/UL 16

24V DC

Sink

-- -

14.6

(0.6)

90

(3.5)

87

(3.4)

0.15

(0.33)

FX

2NC

-16EYT-D/UL - - 16 Transistor Sink

FX

2NC

-32EX-D/UL 32

24V DC

Sink

-- -

26.2

(1.0)

0.2

(0.44)

FX

2NC

-32EYT-D/UL - - 32 Transistor Sink

FX

0N

-8EX-UA1/UL

FX

2N

-8EX-UA1/UL

8

110V

AC

inputs

-- -

43

(1.7)

90

(3.5)

87

(3.4)

0.2

(0.44)

FX

0N

-8EX-ES/UL

FX

2N

-8EX-ES/UL

8

24V DC

Sink/

Source

-- -

FX

0N

-8ER-ES/UL

FX

2N

-8ER-ES/UL

44

Relay

-

FX

0N

-8EYR-ES/UL

FX

2N

-8EYR-ES/UL

--8 -

FX

0N

-8EYT-ESS/UL

FX

2N

-8EYT-ESS/UL

- - 8 Transistor Source

FX

0N

-16EX-ES/UL 16

24V DC

Sink/

Source

-- -

70

(2.8)

0.3

(0.66)

FX

0N

-16EYR-ES/UL - - 16 Relay -

FX

0N

-16EYT-ESS/UL - - 16 Transistor Source

FX2NC Series Programmable Controllers Introduction 1.

1-4

FX

2N

-16EX-ES/UL 16

24V DC

Sink/

Source

-- -

40

(1.6)

90

(3.5)

87

(3.4)

0.3

(0.66)

FX

2N

-16EYR-ES/UL - - 16 Relay -

FX

2N

-16EYT-ESS/UL - - 16 Transistor Source

Table 1.3 : Connector conversion adapter

MODEL DESCRIPTION

DIMENSIONS

mm (inches)

MASS

kg (lbs)

W H D

FX

2NC

-CNV-IF

Extension blocks and special functions blocks

of FX

2N

and FX

0N

is connected by this adapter

14.6

(0.6)

90

(3.5)

74

(2.9)

0.15

(0.33)

Table 1.2 : Extension blocks

MODEL

INPUT OUTPUT

DIMENSIONS

mm (inches)

MASS

kg (lbs)

QTY TYPE QTY DEVICE TYPE

W H D

FX2NC Series Programmable Controllers Introduction 1.

1-5

Figure 1.2 :Extension block dimensions

FX

0N

, FX

2N

Extension block dimensions

→

(See sec. 3.7)

UNITS: mm (inches)

X0

X2

X3

X4

X5

X6

X1

X7

POWER

X0

X2

X3

X4

X5

X6

X1

X7

87(3.43)

74(2.91)

13

90(3.54)

FX

2NC

-32E

FX

2NC

-16E

14.6(0.57)

(0.51)

26.2(1.03)

DIN Rail: 35mm

(1.38)

Power supply connectors for

input extension blocks

FX2NC Series Programmable Controllers Introduction 1.

1-6

Figure 1.3 :Connector conversion adapter

Table 1.4 :Special function blocks

MODEL DESCRIPTION

NUMBER

OF I/O

POWER SUPPLY

DIMENSIONS

mm (inches)

MASS

kg (lbs)

I O

Internal

5V DC

External

24V DC

W H D

FX

2N

-2AD

Analog to digital converter

- 8 - 20mA

50mA

*1

43

(1.7)

90

(3.5)

87

(3.4)

0.2(0.44)

FX

2NC

-4AD - 8 - 50mA 130mA

20

(0.8)

89

(3.5)

0.13

(0.29)

FX

2N

-4AD - 8 - 30mA 55mA

55

(2.1)

87

(3.4)

0.3(0.66)

FX

2N

-8AD - 8 - 50mA 80mA

75

(2.9)

75

(2.9)

0.4(0.88)

90(3.54)

14.6(0.57)

74(2.91)

DIN Rail: 35mm

(1.38)

UNITS: mm (inches)

FX2NC Series Programmable Controllers Introduction 1.

1-7

FX

0N

-3A

Analog / Digital converter

- 8 - 30mA

90mA

*1

43

(1.7)

90

(3.5)

87

(3.4)

0.2(0.44)

FX

2N

-5A - 8 - 70mA 90mA

55

(2.1)

0.3(0.66)

FX

2N

-2DA

Digital to analog converter

- 8 - 30mA

85mA

*1

43

(1.7)

0.2(0.44)

FX

2NC

-4DA - 8 - 30mA 130mA

24

(0.9)

89

(3.5)

0.13

(0.29)

FX

2N

-4DA - 8 - 30mA 200mA

55

(2.1)

87

(3.4)

0.3(0.66)

FX

2N

-4AD-PT PT 100 probe interface - 8 - 30mA 50mA

FX

2N

-4AD-TC Thermo-couple interface - 8 - 30mA 50mA

FX

2N

-2LC Temperature control - 8 - 70mA 55mA

FX

2N

-1HC

High speed counter

- 8 - 90mA -

FX

2NC

-1HC - 8 - 90mA -

20.2

(0.8)

89

(3.5)

0.13

(0.29)

FX

2N

-1PG-E

Pulse output, Position

control

- 8 - 55mA 40mA

43

(1.7)

87

(3.4)

0.2(0.44)

FX

2N

-10PG - 8 - 120mA

70mA

*2

FX

2N

-10GM

Positioning controller

-8- - 5W

60

(2.4)

0.3(0.66)

FX

2N

-20GM - 8 - - 10W

86

(3.4)

0.4(0.88)

Table 1.4 :Special function blocks

MODEL DESCRIPTION

NUMBER

OF I/O

POWER SUPPLY

DIMENSIONS

mm (inches)

MASS

kg (lbs)

I O

Internal

5V DC

External

24V DC

W H D

FX2NC Series Programmable Controllers Introduction 1.

1-8

*1 : Internal 24V DC

*2 : When the voltage of the external DC power supply is 24V DC and 5V DC, the current is 70 mA and

100 mA, respectively.

*3 : Maximum number of I/O points per system Connection is allowed as far as the following condition is

satisfied:

(Actual number of I/O points of PLC) + (Number of points occupied by special extension blocks) +

(Number of points occupied by FX

2N

-16CCL-M: 8) + (32 x Number of remote I/O modules)

≤

256

*4 : For details, refer to the FX

2N

-64CL-M user's manual.

*5 : The value depends on the switch setting.

FX

2N

-1RM-E-

SET

Programmable cam switch - 8 - - 5W

55

(2.1)

111

(4.4)

97

(3.8)

0.5(1.1)

FX

2N

-232IF RS-232C Interface block - 8 - 40mA 80mA

55

(2.1)

90

(3.5)

87

(3.4)

0.3(0.66)

FX

2N

-16CCL-M CC-Link Interface block *3 8 *3 - 150mA

85

(3.3)

0.4(0.88)

FX

2N

-32CCL CC-Link Interface block - 8 - 130mA 50mA

43

(1.7)

0.2(0.44)

FX

2N

-64CL-M CC-Link/LT Interface block *4 8 *4 190mA

25mA

*4

0.15

(0.01)

FX

2N

-16LNK-M

MELSEC-I/O LINK

Remote I/O system master

block

*5 200mA 90mA 0.5(1.1)

FX

0N

-16NT Net-mini interface 8 8 20mA 60mA 0.2(0.44)

Table 1.4 :Special function blocks

MODEL DESCRIPTION

NUMBER

OF I/O

POWER SUPPLY

DIMENSIONS

mm (inches)

MASS

kg (lbs)

I O

Internal

5V DC

External

24V DC

W H D

Page is loading ...

Mitsubishi Electronics FX2NC User manual

This manual is also suitable for

Mitsubishi Electronics FX2NC User manual

Related papers

Other documents