Akai FS40-U3B User manual

Brand: Akai

Model: FS40-U3B

Type: User manual

N13275

40cm Chrome

Pedestal Fan

FS40-U3B

Instruction Manual

AFTER SALES SUPPORT

NZ: 0800 836 761

AU: 1300 886 649

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

1. The appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

2. Young children should be supervised to ensure that they do not play with the

appliance.

3. To reduce the risk of electric shock of injury to persons, make sure unit is switch

to “o” position and unplugged from electrical outlet before cleaning.

4. Do not leave the fan running unattended.

5. If the supply cord is damaged, it must be replaced by the manufacturer or its

service agent or a similarly qualied person in order to avoid a hazard.

RULES FOR SAFE OPERATION:

When using electrical appliances, basic precautions should always be followed to

reduce the risk of re, electric shock and injury to persons, including the following:

1. Never insert ngers, pencils or any other object through the grille when fan is

running.

2. Disconnect fan when moving from one location another.

3. Disconnect fan when removing grilles for cleaning.

4. Be sure fan is on a stable, even surface when operating to avoid overturning.

5. DO NOT use fan in window. Rain may create an electrical hazard. Do not leave

the fan operating adjacent to an area where water has been collected to avoid

the potential of electrical hazard.

6. Do not leave the appliance running or operable in a place where young

children could have access to without supervision.

INTRODUCTION:

The Stand Fan features three speeds, a swivel action head giving a smooth oscilla-

tion action along with low noise levels, low electrical usage, reliability with safety,

while still providing ecient air ow.

OPERATION

The power switch is incorporated in the speed control switch on the top of the fan.

0- The Fan is switched O

1- The Fan operates at the lowest speed

2- The Fan operates at the medium speed

3- The Fan operates at the highest speed

• Thefancanoperateinoscillationorstaticmode.

• Tomakethefanheadoscillate,pushdowntheOscillationKnob.

• Tostopthefanheadfromoscillating,pull-uptheOscillationKnob.

• Theheadofthefancanbeadjustedupordown,todothisloosentheadjusting

knob, adjust the fan to the desired angle, to secure tighten the adjusting knob.

PART NAME:

1. Screw Nut 2. Front guard 3. Blade 4. Position screw 5. Rear guard

6.Powerswitch7.OscillationKnob8.Motor9.Powercord

10. Tube 11. Joint screw 12. Base Addition part 13. Base

ASSEMBLY:

If your fan comes ready assembled

ignore this part.

1 After removing everything from

the carton, locate the motor unit

(item8)andseparatethefrontguard

(item 2) and back guard (item 5) if they

are connected.

2 Locate the rear guard (item 5) and

align with 4 protruding indents on

themotorunit(item8).Thesafety

grille will only t one way over the

pro-truding intents with the handle

facing up. insert 4 locking screws (item 4)

and tighten to secure the rear guard to the motor unit.

3 Locate the fan blades (item 3) and align the centre of the blades over the metal spindle

protruding from the motor unit. The intent on the metal spindle aligns with the locking

screw on the fan blades. After the blade has been put on, tighten the locking screw on

the fan blades and ensure that the blades is secured to the motor unit.

4 Align the front guard to the rear guard and lock into place with 3 locking tabs

that are located on the guard. Locate the security nut and bolt (item 1) and secure

the front and rear guards together with security nut and bolt. This is a safety

precaution to prevent the accidental dismantling of the fan.

5 Locate the pedestal base of the fan(item 13). Insert the base of the stand (item

10) into the pedestal base,then fasten the base (item12,13) and the pole with the

screws provided.

6 Undo the thumbscrew at the top of the stand(item 10) and align the motor unit

complete with guards before fastening.

THERMAL CUT-OUT DEVICE

A Thermal protector device was mounted in the motor. When overheats due to

various reasons, the temperature of the motor reaches the fusing point, it will cut

o automatically, make the fan safe eciently. When the protector is fused, the fan

should be eliminated trouble and replace a new thermal protector before the fan is

used again.

CLEANING INSTRUCTIONS

1. Be sure to unplug the fan from electrical supply source before cleaning.

2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge.

Thoroughly remove soap lm with clean water.

3. To disassemble each part, reverse the order of assembly.

Distributed by Tempo (Aust) Pty Ltd ABN 70 106 100 252

Unit8/14RodboroughRd,FrenchsForest,AustraliaNSW2086

Customer Help Line : 1300 886 649 (AU) | 0800 836 761 (NZ)

Telephone:(02)99752199Fax:(02)99752688

Email: info@tempoaustralia.com.au

Akai FS40-U3B User manual

Akai FS40-U3B User manual

Related papers

Other documents