Matsui MAT-PFS16 Instruction book

Instruction Book

16" Pedestal Fan

MAT-PFS16

GB

Getting to know your fan

Please read these instructions and have a good look

at

the illustrations before using your fan.

We continually strive to improve our products, specifications may change without prior notice

Oscillating pin

On

/ off

and

speed buttons

Power

cord

Front

guard

Rear

guard

GB

Safety first !

Your fan should be used in such a

way

that it is protected from moisture. e.g.

condensation,

splashed water etc

Stand

your fan on a stable, level

surface

during use.

Do

not place or store your fan where

it

can fall or be pulled into water or any

other

liquid.

Do

not reach for the appliance if it

has

fallen in any water or any

other

liquid. Unplug immediately.

Your fan should be unplugged

from

the wall socket when left unused

for

a long time.

Your

fan should be placed away

from

heat sources such as radiators,

gas/electric

fires and direct sunlight.

Keep

the power cord away from any

heated

surfaces.

Use

the appliance only for its intended

use,

as described in this manual.

Do

not use outdoors.

It is DANGEROUS to insert fingers or

objects

into the grill. Do not allow young

children

to play with your fan.

Close

supervision is necessary when your

fan

is used near children.

Never use your fan if it is

damaged

in any way.

Do

not remove any fixed covers. Never

use

this appliance if it is not working

properly,

or if it has been dropped or

damaged

.

If the supply cord is damaged it MUST

be

repaired by a qualified person.

GB

Align the BASE with the neck of

the

fan and use the BASE SET

SCREW

to join the two together.

1

How to assemble your fan

Make sure

your fan

is

unplugge

d

before

you

attempt

to

assembl

e

Push

the BLADE onto the MOTOR

SHAFT.

Ensure the slot in the BLADE

matches

up with the notch on the

MOTOR

SHAFT.

3

2

Align

the

rear guard with the three

pins on

the MOTOR

(ensuring the

handle is

positioned

at the top of the

fan).

Insert

the plastic nut and tighten.

Adjusting Knob

Motor

Oscillating pin

Rear Guard

Screw

Nut

ON/OFF

Base

Power Cord

Front Guard

Blade

Screw cover

Plastic nut

Height Adjusting

Knob

and Speed Buttons

GB

4

Tighten the screw cover to secure

the blades

.

Insert a screw into the hole at the

top of the fan guards and tighte

n

6

5

Fit the front guard by securing it with

the 4 locking grips. Ensure that

with a nut.

the

hole is aligned at the top of the fan.

Note: The screw tighte

ns in a

n

anti-clockwise directio

n

GB

321

How to use your fan

Plug into a mains socket and

switch

on at the wall.

To

make the fan move from side to

side press the

OSCILLATING PI N

down.To stop, pull the pin up.

Loosen the ADJUSTING KNOB,

4

p

lug

i

n

t

o th

e

main

s s

ocke

t

.

E

n

s

ure

the

fan i

s

swi

t

c

hed

o

ff at th

e co

n

t

rol switch befo

re inse

rting th

e

adjust the tilt angle, retighten an

d

switch the unit back on

.

Press

the

buttons 1, 2 or

3 to control

the

fan

speed. Use the ‘0’ button

to stop the fan.

5

Loosen HEIGHT ADJUSTING

KNOB and move the tube up or

down then tighten the

knob t

o

adjust the height level

.

GB

Cleaning

The fan blade and body of the unit should be cleaned

using

a cloth dampened with warm water and

detergent.

Make sure you do not allow water to seep

into

the controls or motor housing of your fan.

Always

unplug your fan from the mains supply

before

attempting cleaning. Do not use harsh cleaners

or

solvents on the fan as they may damage the casing.

Specifications

Power Supply..... ...230V~50Hz

Rated

Po

wer.........50

W

GB

No part of this publication may be reproduced,

stored

in a retrieval system or transmitted, in any

form

or by any means, without the prior permission

in

writing of Dixons Stores Group, nor be otherwise

circulated

in any form of binding or cover other

than

that in which is published and without a

similar

condition including this condition being

imposed

on the subsequent purchaser

a

w

t

s

e

i

s

a

e

h

t

r

o

f y

a

d

o

t

k

u

.

oc

.

r

e

ts

a

m

t

r

a

P

tisi

V

.

s

e

i

r

o

s

e

c

a

d

n

a

s

e

r

a

p

s

l

a

c

i

r

t

c

e

l

e

y

u

b

o

t

y

v

i

l

e

d

n

a

c

e

w

kc

o

t

s

n

i

s

t

c

u

d

o

r

p

0

,

0

5

r

e

v

o

h

t

i

W

.y

a

d

t

x

e

n y

r

ev

e

h

t

r

o

d

r

u

o

y

o

t

c

e

ri

d

r

e

t

i

s

i

V

k

u

.

o

c

.

r

e

t

s

a

m

t

r

a

p

.

w

l

a

c

ro

8

3

1

0

6

0

7

8

0

)

y

l

n

o

s

r

e

mo

t

s

u

c

K

U

(

.

e

ta

R

la

no

i

ta

N

ta deg

rah

c

s

l

a

C

This symbol on the product or in the instructions means that your electrical and electronic

equipment

should be disposed at the end of its life separately from your household waste.

There

are separate collection systems for recycling in the EU.

For

more information, please contact the local authority or your retailer where you purchased

the

product.

Matsui MAT-PFS16 Instruction book

Matsui MAT-PFS16 Instruction book

Related papers

Other documents