Target 249-10-0021 Assembly Instructions Manual

Target
Brand
Target
Model
249-10-0021
Type
Assembly Instructions Manual
>>
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
windham
media stand
assembly instructions
style # WNMEDIASBK (black)
dpci # 249-10-0021
style # WNMEDIASRD (red)
dpci # 249-10-0316
style # WNMEDIASYL (yellow)
dpci # 249-10-0317
style # WNMEDIASBL (teal)
dpci # 249-10-0310
style # WNMEDIASWH (shell)
dpci # 249-10-0312
style # WNMEDIASGY (gray)
dpci # 249-10-0311
style # WNMEDIASNV (navy)
dpci # 249-10-0448
style # WNMEDIASGG (green garnish)
dpci # 249-10-0920
style # WNMEDIASOV (overcast)
dpci # 249-10-0921
style # WNMEDIASBN (banana split)
dpci # 249-10-0922
2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed
3
table of contents
introduction
2
hardware
4
parts list
5
how to use the cam lock system
6
assembly
7-12
QUESTIONS?
Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.
4
hardware
(H1) x 12
wooden dowel
(H2) x 12
cam bolt
(H3) x 12
cam
(H4) x 28
pan head screw
(H5) x 8
at head screw
(H6) x 8
shelf support
(H7) x 2
knob bolt
(H8) x 2
knob
(H9) x 1
wall strap
(H10) x 1
wall anchor
(H11) x 1
38mm wall screw
(H13) x 1
18mm truss head screw
(H14) x 2
door magnet
(H15) x 2
5/8” washer
5
exploded diagram
ITEM DESCRIPTION QUANTITY
A top panel 1
B right side panel 1
C left side panel 1
D bottom panel 1
E center panel 1
F foot 1
G back panel 1
H shelf 2
I right door 1
J left door 1
how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are ush
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
6
4. 5.
1.
2. 3.
7
step 1: attach left/right/center panels and foot to bottom panel
(H1) x 6
wooden dowel
(H2) x 6
cam bolt
(H3) x 6
cam
1.1. Carefully tap small wooden dowels into place in left side panel, right side panel, and bottom panel. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in left side panel, right side panel, and bottom panel.
1.3. Refer to page 6 for instructions on how to use the cam lock system. Do not over tighten bolts.
1.4. Align center foot with pre-drilled hole to attach to bottom panel.
step 2: attach door magnets and top panel
(H1)
x 6
wooden dowel
(H2) x 6
cam bolt
(H3) x 6
cam
(H14) x 2
door magnet
(H4) x 4
pan head screw
2.1. Align pan head screws with pre-drilled holes to attach door magnets to top panel. Do not over tighten screws.
2.2. Carefully tap small wooden dowels into place in top panel. Leave 1/2” of the dowels sticking out.
2.3. Screw-In cam bolts must be screwed down ush in top panel.
2.4. Refer to page 6 for instructions on how to use the cam lock system.
2.5. Do not over tighten bolts.
8
(H1) x 6
wooden dowel
(H2) x 6
cam bolt
(H3) x 6
cam
(H14) x 2
door magnet
(H4) x 4
pan head screw
step 3: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 24
pan head
screw
3.1. Make sure the pan head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.
9
hole for anti-tip
10
step 4: install adjustable shelves
(H6) x 8
shelf support
4.1. Insert shelf supports into desired hole. Dierent holes accommodate dierent shelf heights.
4.2. Angle shelf to t between the rails and set on top of shelf supports.
step 5: attach doors and knobs
(H5) x 8
at head screw
(H7) x 2
knob bolt
(H8) x 2
knob
5.1 Align at head screws with pre-drilled holes to attach doors to cabinet. Do not over tighten screws.
5.2 Align knob bolts with pre-drilled holes to attach knobs to cabinet. Do not over tighten bolts.
11
(H7)
(H7)
step 6: install anti-tip kit
(H13) x 1
18mm truss head screw
(H9) x 1
wall strap
(H15) x 2
washer
(H10) x 1
wall anchor
(H11) x 1
38mm wall screw
Position against wall
Mark position of strap hole on
wall
Drill 1/4’’ hole
Tap in wall anchor
Fasten anti-tip strap
with at-head screw provided
12
(H10)
(H9)
(H13)
(H15)
(H11)
(H15)
Mark position of strap hole on
wall

  
 

   
    
    
     

     

     

  

  
    
 

   
    
  
 
 
 
    

  

1. WARNING - Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed
on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child.
2. WARNING - Relocating audio and/or video equipment to furniture not specically designed to support audio and/or video equipment may result
in death or serious injury due to the furnishing collapsing or over turning onto a child.
3. This unit has been designed for the weight shown. Exceeding this recommended weight could result in excessive “sagging” of the top. Extreme
overloading can cause failure of the top and possible injury.
4. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.
A
A
1313QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
holds at panel TVs
up to 55’’ or 94 lbs.
interior shelf capacity 40 lbs.

© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Target 249-10-0021 Assembly Instructions Manual

Target
Brand
Target
Model
249-10-0021
Type
Assembly Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents