Du Ha 20025 User guide

Brand: Du Ha

Model: 20025

Type: User guide

Materials Needed:

// 8mm Socket

Installation Instructions: Solid Bench Seat

Tilt the back of the rear seat forward.

Remove the jack handles from the current plastic tray (if applicable). Using an 8mm

socket, remove bolts holding current plastic tray. Remove tray from truck. (Note: If you

experience problems removing bolts you may need to apply upward pressure from under tray.)

Turn the DU-HA upside down. Using clear tape, tape the two spacers directly over the

pre-drilled holes in the bottom front of the DU-HA, directly above the DU-HA lettering.

Turn the DU-HA back over. Line up the DU-HA so the pre-drilled holes are directly above

the holes in the oor of the truck, with the DU-HA lettering facing forward.

(Note: The spacers are designed to keep the back seat from hitting the DU-HA when the seats are in their

upright position. If the seat still hits, add extra washers.)

Screw in each bolt using an 8mm socket. Do not overtighten.

If desired, install organizer/gun racks with plastic stiffeners by snapping them into the

slots in the DU-HA (as pictured). Gun racks can be installed to hold two guns or one gun

depending on how you install them. If you removed your jack handles from the existing

tray you can place the jack handles in DU-HA or on oor in front of DU-HA.

Safety Instructions:

Warning: Seat back must be latched up at all times

while vehicle is moving. Make sure the DU-HA is

secured in the vehicle according to installation

instructions. Do not store explosives or hazardous

materials in the DU-HA. Do not place loaded

guns in the DU-HA.

For further instructions refer to truck owners

manual or contact DU-HA, Inc.

00-07 Ford F-250—F-550 Super Duty Crew Cab & Reg. Cab

Behind-the-Seat Storage

Installation Instructions

DU-HA, Inc. // website: www.du-ha.com // phone: 1.866.306.DUHA (3842) // fax: 1.218.998.4013 // 306 Saint Andrews Street South, Fergus Falls, MN 56537

Fits DU-HA Part Numbers

Part Description Qty

A DU-HA Storage Unit 1

B Foam Organizer / Gun Rack 2

C Plastic Stiffener 2

D Spacers - 13RS075009 3/4”x.5” 2

E Nylon Strap with Buckle 2

20020

20022

20025

20032

2 straps are

included to

help secure

guns/gear in

place.

DIVIDER – 20020

Materials Needed:

// Phillips Screwdriver // 13mm Socket // 8mm Socket

Installation Instructions: 60/40 Split Bench Seat

Tilt the backs of the rear seats forward.

On driver’s side rear seat, remove plastic cover (located by seat bottom tilt lever) using Phillips screwdriver,

then remove plastic cover from side rear portion of seat (be careful not to break spring clips when removing).

Remove the two bolts holding the rear seat back using a 13mm socket, then pull seat back forward.

Remove jack handles from current plastic tray (if applicable). Using an 8mm socket, remove bolts

holding current plastic tray. Remove tray from truck. (Note: If you experience problems removing bolts you may

need to apply upward pressure from under the tray.)

Remove jack.

Turn the DU-HA upside down. Using clear tape, tape the two spacers directly over the pre-drilled

holes in the bottom front of the DU-HA, directly above the DU-HA lettering.

Turn the DU-HA back over. Line up the DU-HA so the pre-drilled holes are directly above the holes

in oor of the truck, with the DU-HA lettering facing forward. (Note: The spacers are designed to keep the

back seat from hitting the DU-HA when the seats are in their upright position. If the seat still hits, add extra washers.)

Screw in each bolt using an 8mm socket. Do not overtighten.

Re-attach seat back in the same manner as removed using existing bolts and 13mm socket. Re-attach

plastic covers. Snap rear cover back into same holes and secure front cover with Phillips screwdriver.

If desired, install foam organizer/gun racks with plastic stiffeners by bending and snapping them into

channel slots in DU-HA. Gun racks will hold two guns or one gun depending on how you install them.

(Note: You may place jack handles in the DU-HA or on the oor in front of the DU-HA.)