Miller HDC 1500DX CE Owner's manual

Brand: Miller

Model: HDC 1500DX CE

Category: Welding System

Type: Owner's manual

This manual is also suitable for

LC707092

50, 60 Hz

Processes

Description

OM-212 296C

November 2003

Submerged (SAW) Welding

Submerged Arc Controller For

Automatic Welding

HDC 1500DX

Miller Electric manufactures a full line

of welders and welding related equipment.

For information on other quality Miller

products, contact your local Miller distributor to receive the latest full

line catalog or individual catalog sheets. To locate your nearest

distributor or service agency call 1-800-4-A-Miller, or visit us at

www.MillerWelds.com on the web.

Thank you and congratulations on choosing Miller. Now you can get

the job done and get it done right. We know you don’t have time to do

it any other way.

That’s why when Niels Miller first started building arc welders in 1929,

he made sure his products offered long-lasting value and superior

quality. Like you, his customers couldn’t afford anything less. Miller

products had to be more than the best they could be. They had to be the

best you could buy.

Today, the people that build and sell Miller products continue the

tradition. They’re just as committed to providing equipment and service

that meets the high standards of quality and value established in 1929.

This Owner’s Manual is designed to help you get the most out of your

Miller products. Please take time to read the Safety precautions. They

will help you protect yourself against potential hazards on the worksite.

We’ve made installation and operation quick

and easy. With Miller you can count on years

of reliable service with proper maintenance.

And if for some reason the unit needs repair,

there’s a Troubleshooting section that will

help you figure out what the problem is. The

parts list will then help you to decide the

exact part you may need to fix the problem.

Warranty and service information for your

particular model are also provided.

Miller is the first welding

equipment manufacturer in

the U.S.A. to be registered to

the ISO 9001:2000 Quality

System Standard.

Working as hard as you do

− every power source from

Miller is backed by the most

hassle-free warranty in the

business.

From Miller to You

Mil_Thank 7/03

TABLE OF CONTENTS

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Arc Welding Hazards 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Additional Symbols For Installation, Operation, And Maintenance 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. California Proposition 65 Warnings 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-5. Principal Safety Standards 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6. EMF Information 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 2 − CONSIGNES DE SÉCURITÉ − À LIRE AVANT UTILISATION 5 . . . . . . . . . . . . . . . . . . . . . . . . . .

2-1. Signification des symboles 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-2. Dangers relatifs au soudage à l’arc 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien de l’appareil. 7 . . . . . . . . . . .

2-4. Principales normes de sécurité 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-5. Information sur les champs électromagnétiques 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 3 − DEFINITIONS (CE Models Only) 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-1. Warning Label Definitions 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2. Manufacturer’s Rating Label For CE Products Only 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-3. Symbols And Definitions* 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 4 − SPECIFICATIONS 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-1. Weld Control 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2. Description 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 5 − INSTALLATION 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-1. Typical Equipment Location 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2. Mounting Hole Layout 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-3. Rating Label For Non-CE Products Only 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-4. Connection Diagram With Miller Power Sources 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-5. Connection Diagram With Non-Miller Power Sources 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-6. Left Side Panel Connections 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-7. Terminal Block TB1 And TB2 Connections 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-8. Terminal Block TB1 Connection Information 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-9. Terminal Block TB2 Connection Information 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-10. Typical Connection Of A Flux Hopper With Automatic 115 VAC To An HDC 1500DX 18 . . . . . . . . . . . . .

5-11. Remote 10 Receptacle RC2 Information 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-12. Remote 14 Receptacle RC1 Information 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 6 − OPERATION 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-1. Safety Equipment 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2. Power Switch And Buttons 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-3. Program Push Buttons 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4. Front Panel Controls 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-5. Upper Display 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-6. Lower Display 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-7. Setup Push Button 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-8. Adjust Control 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-9. Sequence Push Button 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-10. Flux Push Button 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-11. Auxiliary Menus 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 7 − Motor Types 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 8 − Setting Sequence Parameters 28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-1. Sequence Parameters In A Program 28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-2. Calibrating The HDC 1500DX 29 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 9 − MAINTENANCE & TROUBLESHOOTING 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9-1. Routine Maintenance 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9-2. Circuit Breaker CB1 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page is loading ...

dec_con1_11/02

Declaration of Conformity for

European Community (CE) Products

This information is provided for units with CE certification (see rating label on unit).

NOTE

Manufacturer’s Name: Miller Electric Mfg. Co.

Manufacturer’s Address: 1635 W. Spencer Street

Appleton, WI 54914 USA

Declares that the product: HDC 1500DX

conforms to the following Directives and Standards:

Directives

Low Voltage Directive: 73/23/EEC

Electromagnetic Compatibility (EMC) Directive: 89/336/EEC

Machinery Directives: 89/392/EEC, 91/368/EEC, 93/C 133/04, 93/68/EEC

Standards

Arc Welding Equipment Part I: Welding Power Sources: IEC 974-1

(April 1995 − Draft Revision)

Arc Welding Equipment: Wirefeed Systems: IEC 974-4

(May 1995 − Draft Revision)

Degrees of Protection Provided By Enclosures (IP Code): IEC 529:1989

Insulation Coordination For Equipment With Low-Voltage Systems:

Part I: Principles, Requirements and Tests: IEC 664-1: 1992

Electromagnetic Compatibility, (EMC): EN 50199

European Contact: Mr. Danilo Fedolfi, Managing Director

ITW WELDING PRODUCTS ITALY S.r.l.

Via Privata Iseo 6/E

20098 San Giuliano

Milanese, Italy

Telephone: 39(02)98290-1

Fax: 39(02)98290-203

Page is loading ...

OM-212 296 Page 1

Return To Table Of Contents

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING

som _8/03

1-1. Symbol Usage

Means Warning! Watch Out! There are possible hazards

with this procedure! The possible hazards are shown in

the adjoining symbols.

Y Marks a special safety message.

. Means “Note”; not safety related.

This group of symbols means Warning! Watch Out! possible

ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.

Consult symbols and related instructions below for necessary actions

to avoid the hazards.

1-2. Arc Welding Hazards

Y The symbols shown below are used throughout this manual to

call attention to and identify possible hazards. When you see

the symbol, watch out, and follow the related instructions to

avoid the hazard. The safety information given below is only

a summary of the more complete safety information found in

the Safety Standards listed in Section 1-5. Read and follow all

Safety Standards.

Y Only qualified persons should install, operate, maintain, and

repair this unit.

Y During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks

or severe burns. The electrode and work circuit is

electrically live whenever the output is on. The input

power circuit and machine internal circuits are also

live when power is on. In semiautomatic or automatic wire welding, the

wire, wire reel, drive roll housing, and all metal parts touching the

welding wire are electrically live. Incorrectly installed or improperly

grounded equipment is a hazard.

D Do not touch live electrical parts.

D Wear dry, hole-free insulating gloves and body protection.

D Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the work

or ground.

D Do not use AC output in damp areas, if movement is confined, or if

there is a danger of falling.

D Use AC output ONLY if required for the welding process.

D If AC output is required, use remote output control if present on

unit.

D Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according to

OSHA 29 CFR 1910.147 (see Safety Standards).

D Properly install and ground this equipment according to its

Owner’s Manual and national, state, and local codes.

D Always verify the supply ground − check and be sure that input

power cord ground wire is properly connected to ground terminal in

disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

D When making input connections, attach proper grounding conduc-

tor first − double-check connections.

D Frequently inspect input power cord for damage or bare wiring −

replace cord immediately if damaged − bare wiring can kill.

D Turn off all equipment when not in use.

D Do not use worn, damaged, undersized, or poorly spliced cables.

D Do not drape cables over your body.

D If earth grounding of the workpiece is required, ground it directly

with a separate cable.

D Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

D Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

D Wear a safety harness if working above floor level.

D Keep all panels and covers securely in place.

D Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

D Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

D Do not connect more than one electrode or work cable to any

single weld output terminal.

SIGNIFICANT DC VOLTAGE exists after removal of

input power on inverters.

D Turn Off inverter, disconnect input power, and discharge input

capacitors according to instructions in Maintenance Section

before touching any parts.

Welding produces fumes and gases. Breathing

these fumes and gases can be hazardous to your

health.

FUMES AND GASES can be hazardous.

D Keep your head out of the fumes. Do not breathe the fumes.

D If inside, ventilate the area and/or use exhaust at the arc to remove

welding fumes and gases.

D If ventilation is poor, use an approved air-supplied respirator.

D Read the Material Safety Data Sheets (MSDSs) and the

manufacturer’s instructions for metals, consumables, coatings,

cleaners, and degreasers.

D Work in a confined space only if it is well ventilated, or while

wearing an air-supplied respirator. Always have a trained watch-

person nearby. Welding fumes and gases can displace air and

lower the oxygen level causing injury or death. Be sure the breath-

ing air is safe.

D Do not weld in locations near degreasing, cleaning, or spraying op-

erations. The heat and rays of the arc can react with vapors to form

highly toxic and irritating gases.

D Do not weld on coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the weld

area, the area is well ventilated, and if necessary, while wearing an

air-supplied respirator. The coatings and any metals containing

these elements can give off toxic fumes if welded.

OM-212 296 Page 2

Return To Table Of Contents

Arc rays from the welding process produce intense

visible and invisible (ultraviolet and infrared) rays

that can burn eyes and skin. Sparks fly off from the

weld.

ARC RAYS can burn eyes and skin.

D Wear a welding helmet fitted with a proper shade of filter to protect

your face and eyes when welding or watching (see ANSI Z49.1

and Z87.1 listed in Safety Standards).

D Wear approved safety glasses with side shields under your

helmet.

D Use protective screens or barriers to protect others from flash and

glare; warn others not to watch the arc.

D Wear protective clothing made from durable, flame-resistant mate-

rial (leather and wool) and foot protection.

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks, hot

workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause

sparks, explosion, overheating, or fire. Check and be sure the area is

safe before doing any welding.

WELDING can cause fire or explosion.

D Protect yourself and others from flying sparks and hot metal.

D Do not weld where flying sparks can strike flammable material.

D Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

D Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

D Watch for fire, and keep a fire extinguisher nearby.

D Be aware that welding on a ceiling, floor, bulkhead, or partition can

cause fire on the hidden side.

D Do not weld on closed containers such as tanks, drums, or pipes,

unless they are properly prepared according to AWS F4.1 (see

Safety Standards).

D Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly

unknown paths and causing electric shock and fire hazards.

D Do not use welder to thaw frozen pipes.

D Remove stick electrode from holder or cut off welding wire at

contact tip when not in use.

D Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

D Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

FLYING METAL can injure eyes.

D Welding, chipping, wire brushing, and grinding

cause sparks and flying metal. As welds cool,

they can throw off slag.

D Wear approved safety glasses with side

shields even under your welding helmet.

BUILDUP OF GAS can injure or kill.

D Shut off shielding gas supply when not in use.

D Always ventilate confined spaces or use

approved air-supplied respirator.

HOT PARTS can cause severe burns.

D Do not touch hot parts bare handed.

D Allow cooling period before working on gun or

torch.

MAGNETIC FIELDS can affect pacemakers.

D Pacemaker wearers keep away.

D Wearers should consult their doctor before

going near arc welding, gouging, or spot

welding operations.

NOISE can damage hearing.

Noise from some processes or equipment can

damage hearing.

D Wear approved ear protection if noise level is

high.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode. Since

gas cylinders are normally part of the welding

process, be sure to treat them carefully.

CYLINDERS can explode if damaged.

D Protect compressed gas cylinders from excessive heat, mechani-

cal shocks, slag, open flames, sparks, and arcs.

D Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

D Keep cylinders away from any welding or other electrical circuits.

D Never drape a welding torch over a gas cylinder.

D Never allow a welding electrode to touch any cylinder.

D Never weld on a pressurized cylinder − explosion will result.

D Use only correct shielding gas cylinders, regulators, hoses, and fit-

tings designed for the specific application; maintain them and

associated parts in good condition.

D Turn face away from valve outlet when opening cylinder valve.

D Keep protective cap in place over valve except when cylinder is in

use or connected for use.

D Read and follow instructions on compressed gas cylinders,

associated equipment, and CGA publication P-1 listed in Safety

Standards.

OM-212 296 Page 3

Return To Table Of Contents

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near

combustible surfaces.

D Do not install unit near flammables.

D Do not overload building wiring − be sure power supply system is

properly sized, rated, and protected to handle this unit.

FALLING UNIT can cause injury.

D Use lifting eye to lift unit only, NOT running

gear, gas cylinders, or any other accessories.

D Use equipment of adequate capacity to lift and

support unit.

D If using lift forks to move unit, be sure forks are

long enough to extend beyond opposite side of

unit.

OVERUSE can cause OVERHEATING

D Allow cooling period; follow rated duty cycle.

D Reduce current or reduce duty cycle before

starting to weld again.

D Do not block or filter airflow to unit.

STATIC (ESD) can damage PC boards.

D Put on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to

store, move, or ship PC boards.

MOVING PARTS can cause injury.

D Keep away from moving parts.

D Keep away from pinch points such as drive

rolls.

WELDING WIRE can cause injury.

D Do not press gun trigger until instructed to do

so.

D Do not point gun toward any part of the body,

other people, or any metal when threading

welding wire.

MOVING PARTS can cause injury.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards

closed and securely in place.

H.F. RADIATION can cause interference.

D High-frequency (H.F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

D Have only qualified persons familiar with

electronic equipment perform this installation.

D The user is responsible for having a qualified electrician prompt-

ly correct any interference problem resulting from the installa-

tion.

D If notified by the FCC about interference, stop using the

equipment at once.

D Have the installation regularly checked and maintained.

D Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to

minimize the possibility of interference.

ARC WELDING can cause interference.

D Electromagnetic energy can interfere with

sensitive electronic equipment such as

computers and computer-driven equipment

such as robots.

D Be sure all equipment in the welding area is

electromagnetically compatible.

D To reduce possible interference, keep weld cables as short as

possible, close together, and down low, such as on the floor.

D Locate welding operation 100 meters from any sensitive elec-

tronic equipment.

D Be sure this welding machine is installed and grounded

according to this manual.

D If interference still occurs, the user must take extra measures

such as moving the welding machine, using shielded cables,

using line filters, or shielding the work area.

1-4. California Proposition 65 Warnings

Y Welding or cutting equipment produces fumes or gases which

contain chemicals known to the State of California to cause

birth defects and, in some cases, cancer. (California Health &

Safety Code Section 25249.5 et seq.)

Y Battery posts, terminals and related accessories contain lead

and lead compounds, chemicals known to the State of

California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

For Gasoline Engines:

Y Engine exhaust contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive

harm.

For Diesel Engines:

Y Diesel engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects, and

other reproductive harm.

OM-212 296 Page 4

Return To Table Of Contents

1-5. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

(phone: 305-443-9353, website: www.aws.org).

Recommended Safe Practices for the Preparation for Welding and Cut-

ting of Containers and Piping, American Welding Society Standard

AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Mi-

ami, FL 33126 (phone: 305-443-9353, website: www.aws.org).

National Electrical Code, NFPA Standard 70, from National Fire Protec-

tion Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA

02269−9101 (phone: 617−770−3000, website: www.nfpa.org and www.

sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

from Compressed Gas Association, 1735 Jefferson Davis Highway,

Suite 1004, Arlington, VA 22202−4102 (phone: 703−412−0900, web-

site: www.cganet.com).

Code for Safety in Welding and Cutting, CSA Standard W117.2, from

Canadian Standards Association, Standards Sales, 178 Rexdale

Boulevard, Rexdale, Ontario, Canada M9W 1R3 (phone:

800−463−6727 or in Toronto 416−747−4044, website: www.csa−in-

ternational.org).

Practice For Occupational And Educational Eye And Face Protection,

ANSI Standard Z87.1, from American National Standards Institute, 11

West 42nd Street, New York, NY 10036−8002 (phone: 212−642−4900,

website: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, from National Fire Protection Association,

P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (phone:

617−770−3000, website: www.nfpa.org and www. sparky.org).

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, from U.S. Government Printing Office, Super-

intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there

are 10 Regional Offices−−phone for Region 5, Chicago, is

312−353−2220, website: www.osha.gov).

1-6. EMF Information

Considerations About Welding And The Effects Of Low Frequency

Electric And Magnetic Fields

Welding current, as it flows through welding cables, will cause electro-

magnetic fields. There has been and still is some concern about such

fields. However, after examining more than 500 studies spanning 17

years of research, a special blue ribbon committee of the National

Research Council concluded that: “The body of evidence, in the

committee’s judgment, has not demonstrated that exposure to power-

frequency electric and magnetic fields is a human-health hazard.”

However, studies are still going forth and evidence continues to be

examined. Until the final conclusions of the research are reached, you

may wish to minimize your exposure to electromagnetic fields when

welding or cutting.

To reduce magnetic fields in the workplace, use the following

procedures:

1. Keep cables close together by twisting or taping them.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep welding power source and cables as far away from opera-

tor as practical.

5. Connect work clamp to workpiece as close to the weld as possi-

ble.

About Pacemakers:

Pacemaker wearers consult your doctor first. If cleared by your doctor,

then following the above procedures is recommended.

Page is loading ...

OM-212 296 Page 8

Revenez à la table des matières

2-4. Principales normes de sécurité

Safety in Welding, Cutting, and Allied Processes, norme ANSI Z49.1,

de l’American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

(téléphone : (305) 443−9353, site Web : www.aws.org).

Recommended Safe Practices for the Preparation for Welding and Cut-

ting of Containers and Piping, norme American Welding Society AWS

F4.1, de l’American Welding Society, 550 N.W. LeJeune Rd, Miami, FL

33126 (téléphone : (305) 443−9353, site Web : www.aws.org).

National Electrical Code, norme NFPA 70, de la National Fire Protection

Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA

02269−9101 (téléphone : (617) 770−3000, sites Web : www.nfpa.org et

www.sparky.org).

Safe Handling of Compressed Gases in Cylinders, brochure CGA P−1,

de la Compressed Gas Association, 1735 Jefferson Davis Highway,

Suite 1004, Arlington, VA 22202−4102 (téléphone : (703) 412−0900,

site Web : www.cganet.com).

Code for Safety in Welding and Cutting, norme CSA W117.2, de la Ca-

nadian Standards Association, Standards Sales, 178 boulevard

Rexdale, Rexdale (Ontario) Canada M9W 1R3 (téléphone : (800)

463−6727 ou à Toronto : (416) 747−4044, site Web : www.csa−interna-

tional.org).

Practice For Occupational And Educational Eye And Face Protection,

norme ANSI Z87.1, de l’American National Standards Institute, 11 West

42nd Street, New York, NY 10036−8002 (téléphone : (212) 642−4900,

site Web : www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, norme NFPA 51B, de la National Fire Protection Association,

P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (télé-

phone : (617) 770−3000, site Web : www.nfpa.org et www.sparky.org).

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, de l’U.S. Government Printing Office, Super-

intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (il y a

10 bureaux régionaux − Téléphone pour la Région 5, Chicago : (312)

353−2220, site Web : www.osha.gov).

2-5. Information sur les champs électromagnétiques

Données sur le soudage électrique et les effets des champs magnéti-

ques basse fréquence sur l’organisme

En parcourant les câbles de soudage, le courant crée des champs élec-

tromagnétiques. Les effets potentiels de tels champs restent

préoccupants. Cependant, après avoir examiné plus de 500 études qui

ont été faites pendant une période de recherche de 17 ans, un comité

de spécialistes du National Research Council a conclu : « L’accumula-

tion de preuves n’a pas démontré que l’exposition aux champs

magnétiques et aux champs électriques à haute fréquence constitue un

risque pour la santé humaine ». Toutefois, les études et l’examen des

preuves se poursuivent. En attendant les conclusions finales de la re-

cherche, il serait souhaitable de réduire l’exposition aux champs

électromagnétiques pendant le soudage ou le coupage.

Afin de réduire les champs électromagnétiques en milieu de travail, res-

pecter les consignes suivantes :

1. Garder les câbles ensemble en les torsadant ou en les fixant avec du

ruban adhésif.

2. Mettre tous les câbles du côté opposé à l’opérateur.

3. Ne pas s’enrouler les câbles autour du corps.

4. Garder le poste de soudage et les câbles le plus loin possible de soi.

5. Placer la pince de masse le plus près possible de la zone de soudage.

Consignes relatives aux stimulateurs cardiaques :

Les personnes qui portent un stimulateur cardiaque doivent avant tout

consulter leur médecin. Si ce dernier les déclare aptes, il leur est recom-

mandé de respecter les consignes ci-dessus.

OM-212 296 Page 9Return To Table Of Contents

SECTION 3 − DEFINITIONS (CE Models Only)

3-1. Warning Label Definitions

1 Warning! Watch Out! There

are possible hazards as

shown by the symbols.

2 Electric shock from wiring can

kill.

3 Disconnect input plug or

power before working on

machine.

4 Become trained and read the

instructions before working on

the machine or welding.

3-2. Manufacturer’s Rating Label For CE Products Only

ST-178 794-A

S/N:

VX%

MILLER ELECTRIC MFG. CO., APPLETON, WI USA

115

50/60

1500 100100

. When using a RAD-400 (Miller

part number 195265) running

at maximum speed and fully

loaded, the HDC 1500DX

draws approximately 4 amps.

−

OM-212 296 Page 10 Return To Table Of Contents

3-3. Symbols And Definitions*

Amperes Remote Output

Hertz

Volts Input

Single Phase

Alternating

Current

Rated Welding

Current

Percent Circuit Breaker

Increase/Decrease

Of Quantity

Wire Feed Speed

Protective Earth

(Ground)

Postflow Timer Preflux Timer Start Time

Start Stop

Primary Voltage

Degree Of

Protection

Duty Cycle

Rated Supply

Current

241a Primary

current

Line Connection

Conventional Load

Voltage

On Off

Wire Feed Inch

Down

Wire Feed In Up

Crater Time Program Flux

*Some of these symbols appear on CE models only.

SECTION 4 − SPECIFICATIONS

4-1. Weld Control

Specification Description

Type Of Input Power From Welding

Power Source

Single-Phase 115 Volts AC, 10 Amperes, 50/60 Hertz

Welding Power Source Type Constant Voltage (CV), AC Or DC

Welding Processes Submerged Arc (SAW), And Electro Slag (ESW) Welding

Overall Dimensions Including Knobs,

Receptacles, Etc.

Weld Control — Height: 11.5 in (292 mm); Width: 12.5 in (318 mm); Depth: 7 in (178 mm)

Weight Weld Control — Net: 25.5 lb (11.6 kg)

Weld Voltage And Amperage

Capacity (AC Or DC)

0 To 100 Volts

0 To 1500 Amperes

OM-212 296 Page 11Return To Table Of Contents

4-2. Description

This weld control is designed to au-

tomatically cycle welding events.

This unit can be used with constant

voltage, AC or DC welding power

sources. Relay contacts that work

in conjunction with the weld cycle

are available to interface with other

equipment (such as fixtures and

flux valves). See Section 5-7 and

5-9 for connection information on

TB2.

For information on the wire drive as-

sembly, see Owner’s Manual sup-

plied with the assembly.

803 448-A

SECTION 5 − INSTALLATION

5-1. Typical Equipment Location

Ref. 131 138-A

1 Welding Power Source

2 Side Beam

3 Weld Control

4 Spool Support

5 Wire Drive Assembly

6 Automatic Welding Gun

OM-212 296 Page 12 Return To Table Of Contents

5-2. Mounting Hole Layout

Ref. 803 021-B

8 in

(203 mm)

10-3/4 in

(273 mm)

7 in

(178 mm)*

* Includes front panel knobs

5/16 in

Dia. 4 Holes

(7.9 mm)

5-3. Rating Label For Non-CE Products Only

165 746-B

100

1500

115

50/60

100

. When using a RAD-400 (Miller

part number 195265) running

at maximum speed and fully

loaded, the HDC 1500DX

draws approximately 4 amps.

OM-212 296 Page 13Return To Table Of Contents

5-4. Connection Diagram With Miller Power Sources

Customer must supply the following: power source, wire drive assembly and drive rolls, gun,

welding wire, weld cables, and flux system for the desired application.

Note

Voltage

Sensing

Cords

10-Pin Motor

Control Cord

14-Pin Welding

Power Source

Control Cord

Flux Valve

Cord

Welding Cables

(SAW)

(Optional)

Y Turn Off welding power

source and weld control

and disconnect input

power before making

connections.

This unit is supplied with 10-pin

and 14-pin cords. Select the

proper cord and make each of

the connections shown.

OM-212 296 Page 14 Return To Table Of Contents

5-5. Connection Diagram With Non-Miller Power Sources

Customer must supply the following: power source, Miller shunt control, power source control

cable, wire drive assembly and drive rolls, gun, welding wire, weld cables, and flux system for

the desired application.

Note

Voltage

Sensing

Cords

10-Pin Motor

Control Cord

Welding Power

Source Control

Cord

Flux Valve

Cord

Welding Cables

Y Turn Off welding power

source and weld control

and disconnect input

power before making con-

nections.

. For non-MILLER power

sources, terminal block TB1

is required for hookup (See

Sections 5-7 and 5-8).

A voltage sense lead is required

when using a non−MILLER pow-

er source. To connect a voltage

sense lead, route a two conduc-

tor lead through user access

hole and connect to terminals of

TB2 (see Section 5-7). Connect

other end of voltage sensing lead

to the workpiece, and to the

torch.

(SAW)

SHUNT

CONTROL

OM-212 296 Page 15Return To Table Of Contents

1 Receptacle

2 Keyway

3 Access Holes - For Customer

Use: Connections To Terminal

Blocks, Flux Valve, etc.

Y Turn Off welding power

source and weld control and

disconnect input power be-

fore opening access door.

. Install strain relief (customer

supplied) in access hole.

Route incoming cables through

user access hole prior to making

connections to internal terminal

blocks.

4 14-Pin Receptacle:

Connection To Welding Power

Source.

5 10-Pin Receptacle:

Connection to Wire Drive

Motor

To connect matching interconnect-

ing cord to one of the above

receptacles, align keyway, insert

plug, and tighten threaded collar.

Connect remaining end of cord to

matching receptacle on applicable

equipment.

5-6. Left Side Panel Connections

1 2

Ref. 803 022-B

Example Receptacle

OM-212 296 Page 16 Return To Table Of Contents

5-7. Terminal Block TB1 And TB2 Connections

Ref. 803 450-B

Y Turn Off welding power

source and weld control and

disconnect input power be-

fore opening access door.

1 Access Door

Remove securing screw and open

access door.

2 Terminal Block TB2

3 Terminal Block TB1

4 Securing Screw - Terminal

Block

5 Stripped Lead

6 Typical Lead Being

Connected To Terminal Block

7 Access Holes - Used For

Connections To Terminal

Blocks, Flux Valve, etc.

. Install strain relief (customer

supplied) in access hole.

Strip 1/4 in (6 mm) insulation off end

of lead, insert end into proper loca-

tion on TB1 and TB2. Tighten appli-

cable securing screw.

Close and secure access door.

Tools Needed:

1/4 in

(6 mm)

OM-212 296 Page 17Return To Table Of Contents

5-8. Terminal Block TB1 Connection Information

Terminal/Number Receptacle Location Function Information

A - 2 A on 14-Pin

A normally open set of relay contacts connect terminal A to terminal B when

Start is pressed and pre-flux timer times out (contacts are rated 10 amperes, 125

B - 4 B on 14-Pin

Start is pressed and pre-flux timer times out (contacts are rated 10 amperes, 125

volts AC).

C - 75 C on 14-PIn Remote command reference from welding power source.

D - 77 D on 14-Pin Remote circuit common.

E - 76 E on 14-PIn Output command to welding power source (0 to 10 volts DC).

G - 31 G on 14-PIn Circuit common for 24 and 115 volts AC circuits.

I - 32 I on 14-PIn 115 volts AC from welding power source, which is present whenever welding

power source is on.

F F on 14-PIn Current feedback input (1 volt DC per 100 amperes).

H H on 14-PIn Voltage feedback input (1 volt DC per 10 arc volts).

K K on 14-PIn Chassis common.

Remote Stop When connected to remote common, stops HDC 1500DX.

Remote Jog Down When connected to remote common, jogs wire down.

Remote Common Circuit common for remote capabilities.

5-9. Terminal Block TB2 Connection Information

Terminals Function Information

Red 115 volts AC to power flux hopper.

Black Switched 115 volts AC to power flux hopper.

White Circuit common for 115 volts AC for flux hopper.

Green Chassis common for flux hopper.

Side Beam 1 Relay Normally open set of contacts* that close when power source contactor energizes after HDC 1500DX Start

button is pressed and preflux has timed out. Contacts open again when HDC 1500DX Stop button is pressed.

Side Beam 2 Relay Normally open set of contacts* that close when an arc is established. These contacts are used when you want

the side beam to start moving only after an arc has been established. Contacts open again when HDC 1500DX

Stop button is pressed.

Remote Start When connected to remote common, starts HDC 1500DX.

Remote Jog Up When connected to remote common, jogs wire up.

Remote Program When connected to remote common, increments the program.

Remote Sense Sense lead inputs.

* NOTE: All contacts are rated 10 amperes, 125 volts AC.

OM-212 296 Page 18 Return To Table Of Contents

5-10. Typical Connection Of A Flux Hopper With Automatic 115 VAC To An HDC 1500DX

Ref. 803 629-A

Y Turn Off welding power

source and weld control and

disconnect input power be-

fore opening access door.

1 Access Door

Remove securing screw and open

access door.

2 Terminal Block TB2

3 Access Holes - Used For

Connections To Terminal

Blocks, Flux Valve, etc.

. Install strain relief (customer

supplied) in access hole.

Strip 1/4 in (6 mm) insulation off end

of leads. Insert four-conductor

cables from flux system through ac-

cess hole, and make connections

as shown.

Close and secure access door.

Tools Needed:

Four-Conductor Cable

From Flux System

Green Lead

White Lead

Black Lead

Red Lead

Four-Conductor Cable

From Flux System

OM-212 296 Page 19Return To Table Of Contents

5-11. Remote 10 Receptacle RC2 Information

REMOTE 10

Socket Socket Information

A To positive (+) motor armature (115 volts DC motor).

B To negative (−) motor armature (115 volts DC motor).

C To motor field.

D To motor field.

Wirefeed Drive

E Chassis common.

Wirefeed Drive

Motor Hookups

F Tachometer feedback; 0 to +12 volts DC.

Motor Hookups

G 12 volts DC to power tachometer

H Circuit common for +12 volts DC circuit.

I Not used.

J Not used.

10 Pin Motor Cable

Ref. 212 591-A

5-12. Remote 14 Receptacle RC1 Information

Socket

User Accessible

Via TB1

Terminal #

Socket Information

Contactor Control

A A

24 volts AC or 115 volts AC from welding power source (present

whenever power source is On).

Contactor Control

B B

Normally open set of relay contacts connect A to B when Start is

pressed and preflux timer has timed out.

C C Remote command reference from power source; +10 volts DC.

Remote Output Control

D D Remote circuit common.

E E Output command signal to power source; 0 to +10 volts DC.

Amperage/Voltage Feedback

F F

Current feedback input from power source; +1 volt DC per 100 am-

peres.

Amperage/Voltage Feedback

H H

Voltage feedback input from power source; +1 volt DC per 10 arc

volts.

G G Circuit common for 24 and 115 volts AC circuits.

Electrical Input Power

I I

115 volts AC from welding power source (present whenever welding

power source is on). 115 volts AC is present on terminal block TB1

whenever welding power source is on.

GND

K K Chassis common.

14 Pin Interconnecting Cable

Ref. 178 836

Page is loading ...

Miller HDC 1500DX CE Owner's manual

Brand: Miller

Model: HDC 1500DX CE

Category: Welding System

Type: Owner's manual

This manual is also suitable for

LC707092

Download PDF

report

Miller HDC 1500DX CE Owner's manual

This manual is also suitable for

Miller HDC 1500DX CE Owner's manual

Related papers

Other documents