3com WL-607 Quick Installation Manual

Brand: 3com

Model: WL-607

Category: WLAN access points

Type: Quick Installation Manual

This manual is also suitable for

3Com AP9152 802.11n 2.4/5GHz

Single-Band Access Point

Quick Installation Guide

Model WL-607

3CRWE915275 / 3CRWE9152A75

BOM: 3104XXXX

Manual Version:

APW100

www.3com.com

3Com Corporation

350 Campus Drive,

Marlborough, MA,

USA 01752 3064

documentation may be reproduced in any form or by any means or used to make

any derivative work (such as translation, transformation, or adaptation) without

written permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make

changes in content from time to time without obligation on the part of 3Com

Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition

of any kind, either implied or expressed, including, but not limited to, the implied

warranties, terms or conditions of merchantability, satisfactory quality, and fitness for

a particular purpose. 3Com may make improvements or changes in the product(s)

and/or the program(s) described in this documentation at any time.

If there is any software on removable media described in this documentation, it is

furnished under a license agreement included with the product as a separate

document, in the hard copy documentation, or on the removable media in a directory

file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy,

please contact 3Com and a copy will be provided to you.

UNITED STATES GOVERNMENT LEGEND

If you are a United States government agency, then this documentation and the

software described herein are provided to you subject to the following:

All technical data and computer software are commercial in nature and developed

solely at private expense. Software is delivered as “Commercial Computer Software”

as defined in DFARS 252.227-7014 (June 1995) or as a “commercial item” as

defined in FAR 2.101(a) and as such is provided with only such rights as are

provided in 3Com’s standard commercial license for the Software. Technical data is

provided with limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or

FAR 52.227-14 (June 1987), whichever is applicable. You agree not to remove or

deface any portion of any legend provided on any licensed program or

documentation contained in, or delivered to you in conjunction with, this User

Guide.

Unless otherwise indicated, 3Com registered trademarks are registered in the

United States and may or may not be registered in other countries.

3Com and the 3Com logo are registered trademarks of 3Com Corporation.

All other company and product names may be trademarks of the respective

companies with which they are associated.

ENVIRONMENTAL STATEMENT

It is the policy of 3Com Corporation to be environmentally-friendly in all operations.

To uphold our policy, we are committed to:

Establishing environmental performance standards that comply with national

legislation and regulations.

Conserving energy, materials and natural resources in all operations.

Reducing the waste generated by all operations. Ensuring that all waste conforms to

recognized environmental standards. Maximizing the recyclable and reusable

content of all products.

Ensuring that all products can be recycled, reused and disposed of safely.

Ensuring that all products are labelled according to recognized environmental

standards.

Improving our environmental record on a continual basis.

End of Life Statement

3Com processes allow for the recovery, reclamation and safe disposal of all

end-of-life electronic components.

Regulated Materials Statement

3Com products do not contain any hazardous or ozone-depleting material.

Environmental Statement about the Documentation

The documentation for this product is printed on paper that comes from sustainable,

managed forests; it is fully biodegradable and recyclable, and is completely

chlorine-free. The varnish is environmentally-friendly, and the inks are

vegetable-based with a low heavy-metal content.

About This Manual

Organization

3Com AP9152 802.11n 2.4/5GHz Single-Band Access Points Quick Installation Guide

is organized as follows:

Chapter Contents

1 Product Overview

Introduces the hardware specifications, LEDs, and

interfaces of the 3Com AP9152.

2 Preparing for

Installation

Specifies the temperature and humidity

requirements, power supply for installing the 3Com

AP9152.

3 Installing the AP

Introduces how to install the 3Com AP9152 and

how to connect the power supply by PoE.

4 Connecting to AP

Introduces how to connent to and log into the

3Com AP9152.

Conventions

The manual uses the following conventions:

Symbols

Convention Description

Means reader be extremely careful. Improper

operation may cause bodily injury.

Means reader be careful. Improper operation may

cause data loss or damage to equipment.

Means an action or information that needs special

attention to ensure successful configuration or good

performance.

Means a complementary description.

Means techniques helpful for you to make

Convention Description

configuration with ease.

Obtaining Documentation

You can access the most up-to-date 3Com product documentation on the World Wide

Web at this URL: http://www.3com.com.

iii

Table of Contents

1 Product Overview ....................................................................................................... i

Introduction .............................................................................................................. i

Hardware Specifications .......................................................................................... i

LEDs ............................................................................................................... i

Interfaces ....................................................................................................... ii

2 Preparing for Installation ........................................................................................ iii

Unpacking and Inspection ..................................................................................... iii

Temperature and Humidity Requirements ............................................................ iii

Power Supply ........................................................................................................ iii

3 Installing the AP ....................................................................................................... iv

Determining the Installation Site ........................................................................... iv

Installing the AP ..................................................................................................... iv

Mounting the AP on a Wall ........................................................................... iv

Mounting the AP on a ceiling .............................................................................. viii

Mounting the AP to a T-Rail .................................................................................. ix

Power Supply by PoE ............................................................................................ xi

4 Connecting to the AP ............................................................................................. xii

Approved Channels .............................................................................................. xii

Finding the IP Address on Networks with a DHCP Server(FIT AP) .................... xii

Finding the IP Address on Networks Without a DHCP Server(FAT AP) ............. xii

Log into the AP ..................................................................................................... xii

Converting your Managed AP (FIT) to a Stand-alone AP (FAT) ........................ xiii

Converting your Stand-alone AP (FAT) to a Managed AP (FIT) ........................ xiii

Appendix A Product Overview

Introduction

The 3Com AP9152 is an 802.11n access point (AP) product developed by 3Com

Corporation. The AP9152 ships as a FAT AP to provide wireless access independently

without any access controller or serve as a FIT AP (managed) and operate with

wireless local area network (WLAN) switches or access controllers to provide wireless

access for WLAN users. The factory default configuration is FAT mode, and it can

easily be switch between the FIT mode.

Hardware Specifications

The physical dimensions and weight of the AP9152:

Physical dimensions (diameter × thickness) Weight

Φ190 × 60 mm (Φ7.48 × 2.36 in.)

Note: Φ means diameter

0.5 kg (1.10 lb.)

The basic configurations of the AP9152:

Protocols and chassis material Internal antenna

Power

consumption

IEEE 802.11a/b/g/n,

single-RF, plastic mold design

2.4 GHz, gain: 6 dBi

5 GHz, gain: 6 dBi

5.9 W to 7 W

LEDs

When the AP is connected to power, LEDs indicate activities as follows:

LED Color State Description

POWER Green

Steady on The power supply is normal.

Off

The power supply is poorly connected or is

working abnormally.

10/100M

(Ethernet

interface

LED)

Green

Steady on The Ethernet interface is in the link-up state.

Off

The Ethernet interface is in the link-down

state.

Blinking

Data is being transmitted or received at

10/100 Mbps.

1000M

(Ethernet

interface

LED)

Green

Steady on The Ethernet interface is in the link-up state.

Off:

The Ethernet interface is in the link-down

state.

Blinking

Data is being transmitted or received at

1000 Mbps.

2.4G

(Wireless

link LED)

Green

Off

The wireless link is not initialized or the link

is faulty.

Blinking

slowly

The wireless link is working normally

Blinking

rapidly

Data is being transmitted or received.

(Wireless

link LED)

Green

Off

The wireless link is not initialized or the link

is faulty

Blinking

slowly

The wireless link is working normally

Blinking

rapidly

Data is being transmitted or received.

Interfaces

The AP9152 provides a console interface and an Ethernet interface.

iii

Note: The AP9152 provides a reset button and a security slot.

Descriptions of the interfaces on the AP9152:

Interface

silkscreen

Standards and

protocols

Description

CONSOLE RS/EIA-232

The console interface is used for device

configuration and management.

ETHERNET

IEEE802.3

IEEE802.3u

IEEE802.3af

The Ethernet interface can serve as an uplink

interface to access the Internet and as a PoE

interface at the same time.

Caution: When connecting a cable to an interface, pay attention to the interface

silkscreen to avoid connection mistakes.

Appendix B Preparing for Installation

Unpacking and Inspection

Before unpacking the unit, make sure that the package is intact, without any sign of

damage. When unpacking the unit, avoid excessive force, otherwise, the unit inside

the package may get damaged.

After unpacking the unit, check that all items listed on the packing list are contained. If

any of the items are missing, contact your local dealer immediately.

Temperature and Humidity Requirements

The operating temperature and humidity requirements are as follows:

Specification Range

Operating temperature

0°C to 45°C (32°F to 113°F)

Storage temperature

–40°C to +70°C (–40°F to +158°F)

Relative humidity (non-condensing)

5% to 95%

Power Supply

The AP9152 supports PoE power supply.

Appendix C Installing the AP

Note:

1) Make sure that no metal particles (such as screws) fall into the Ethernet or

console interfaces during installation.

2) Before installing the AP9152 to the wall-mounting bracket, connect the

network cable. The network cable can only be UTP cat-5.

3) Before connecting the console cable to the AP9152 for debugging or

pressing the reset button, you need to remove the device from the

wall-mounting bracket.

Determining the Installation Site

Determine the installation site by observing the following principles:



Install the AP in an area away from obstacles that can cause

interference.



Keep the AP far away from electronic devices (such as microwave

ovens) that may generate RF noise.



Ensure that the installation site will not cause any inconvenience or

nuisance.

Note:

1) Make sure the ceiling is strong enough and the structure is suitable in case of

ceiling mounting. Reinforce the ceiling if needed.

2) Us a Kensington lock if physical security is required to protect the AP from

being stolen.

Installing the AP

The AP9152 support three installation methods:



Mounting the AP on a wall



Mounting the AP on a ceiling



Mounting the AP to a T-rail

Mounting the AP on a Wall

The following describes how to mount an AP9152 on a wall:



Installing the wall-mounting bracket on the wall



Installing the AP on the wall-mounting bracket



Locking the AP onto the wall-mounting bracket (optional)

Installing the wall-mounting bracket on the wall

Step1 Place the wall-mounting bracket tightly against the wall where the AP is to be

mounted and mark the locations to drill holes for installing the screws. Then

use a drill with a bit of 6 mm (1/4 in) in diameter to drill holes in the wall. The

hole pattern must be identical with that in the wall-mounting bracket.

Highlight:

There are five mounting holes in total in the wall-mounting bracket of the AP9152.

Select the three round holes (with a diameter of 5 mm, or 0.20 in) for the installation.

Figure1 Mounting hole pattern of, the AP9152 wall-mounting bracket:

Step2 Insert the pointed end of wall anchors into the drilled holes and tap the flat end

of wall anchors with a rubber hammer until they are all flush with the wall

surface.

Step3 Align the holes in the wall-mounting bracket with the wall anchors and insert

screws through the mounting holes into the wall anchors, as shown in Figure1.

Figure2 Install the wall-mounting bracket of the AP9152

(1) Drill hole (2) Wall anchor

(3) Wall-mounting bracket (4) Key-hole clip

(5) Screw

Step1 Adjust the position of the wall-mounting bracket and tighten the screws.

Note: Install the wall-mounting bracket with the arrow on the bracket pointing upwards.

Installing the AP on the wall-mounting bracket

Step1 Align the AP with the key-hole clips on the wall-mounting bracket and hang the

AP on the bracket. See callout 1 in Figure3.

Step2 Press or rotate the AP to fix it. See callout 2 in Figure3. Fix the -shaped

holes on the AP’s rear panel to the key-hole clips on the wall-mounting

bracket.

vii

Figure3 Fix the AP9152 onto the wall-mounting bracket

Note: Rotating the AP9152 clockwise installs the device, while rotating it

counterclockwise uninstalls it.

Locking the AP onto the wall-mounting bracket (optional)

The AP9152 has a security slot on the upper left side, which can be used to lock the

AP to a fixed object to prevent theft. Follow these steps to lock the AP to a fixed object:

Step1 Fix the security cable to a nearby fixed object.

Step2 Insert the locking plate in the security slot to lock the AP.

Figure4 Lock the AP9152 to a fixed object

(2)

(3)

(1)

Before installing the security lock: (1) Security slot

After installing the security lock :

(2) Security lock

(3) Security cable

Note: The lock is user supplied.

viii

Mounting the AP on a ceiling

Note:

1) To use this installation method, make sure that the thickness of the ceiling is

less than 18 mm (0.71 in), and the ceiling can bear the weight of at least 5 kg

(11.02 lb.).

2) You are not recommended to use this method to mount the AP to a location

made of low-intensity materials such as a plaster ceiling. If this installation

method is required in such an environment, put a high-intensity plate beneath

the nut to secure the installation.

Select the two mounting holes of the wall-mounting bracket as shown in Figure5 to

mount the AP on the ceiling (in mm). Follow these steps to mount the AP on the ceiling:

Step1 Drill two holes in the ceiling corresponding to the two mounting holes in the

wall-mounting bracket.

Figure5 mounting holes on the wall-mounting bracket

(1) Mounting holes for mounting on a ceiling

Step2 Insert the bolts through the mounting holes of the wall-mounting bracket and

the drilled holes on the ceiling, and then tighten the nuts on the other side of

the ceiling to secure the wall-mounting bracket as shown in Figure6.

Figure6 Mount the wall-mounting bracket on the ceiling

(1) Bolt inside the ceiling (2) Washer

(3) Nut (4) Wall-mounting bracket

(5) Bolt cap (6) Key-hole clip

Step3 Mount the AP9152 to the wall-mounting bracket. For details, refer to Installing

the AP on the wall-mounting bracket.

Mounting the AP to a T-Rail

Note: The width of the T-rail must be in the range of 14 mm (0.55 in) to 24 mm (0.94).

Follow these steps to mount the AP to a T-rail:

Step1 Loosen the two M3 × 6 screws on each clip holder until the screw heads are

lower than the upper edge of the nuts (do not remove the screws or they may

get lost).

Step2 Adjust the T-rail clips to make the T-rail holder wider than the T-rail, and then

lock the T-rail with the T-rail holder according to the arrow

Figure7 T-rail holder

(1) T-rail clip (2) M4×8 screw nut

(3) M3×6 screw nut (4) Clip holder

(5) M4×8 screw (6) M3×6 screw

(7) Mounting hook (8) T-rail holder

(9) Before installing to the T-rail, loosen the screw nuts until the screw

heads are lower than the upper edge of the nuts.

Step3 Tighten the M3 × 6 screws on the two clip holders until the screw heads touch

the T-rail, and then fix the screws.

Step4 Check that the T-rail holder is fixed to the T-rail.

Step5 Hook the mounting clip of the wall-mounting bracket to the mounting hook of

the T-rail holder, as shown Figure8.

Step6 Insert the two M4 × 8 screws through the two holes (with a diameter of 5 mm,

or 0.20 in) on the wall-mounting bracket according to the dashed line shown in

Figure8 and fix the screws to the T-rail holder.

Step7 Check that the wall-mounting bracket is fixed to the T-rail.

Step8 Install the AP9152 to the wall-mounting bracket. For details, refer to Installing

the AP on the wall-mounting bracket.

Figure8 Mount the AP to the T-rail

(1) M3×6 screw (2) T-rail

(3) Mounting hook (4) T-rail holder

(5) Mounting clip (6) Wall-mounting bracket

(7) Screw hole (8) M4×8 screw

(9) Key-hole clip (10) M4×8 screw

Power Supply by PoE

Power is supplied to the AP9152 through a PoE module or PoE switch. Connect one

end of an Ethernet cable to the Ethernet interface of the AP9152 and the other end to

an Ethernet interface of the PoE device.

Caution: Identify the mark on the device to avoid confusing the console interface for

the Ethernet interface, or vice versa.

xii

Appendix D Connecting to the AP

To connect to the AP, you must first determine the AP’s IP address in one of these

ways.

Approved Channels

Use of this product is only authorized for the channels approved by each country. For

proper installation, select your country from the country-selection list.

To conform to FCC and other country restrictions, your product may be limited in the

channels that are available. If other channels are permitted your country, please visit

the web site for the latest software version. The Appendix B list the Software

Downloads information.

Finding the IP Address on Networks with a DHCP Server(FIT AP)

If your network has a DHCP server, it automatically assigns an IP address to the AP.

Finding the IP Address on Networks Without a DHCP Server(FAT

AP)

If your network does not have a DHCP server, the AP uses a default factory

configuration which includes the following information.



Configure the IP address of the AP as 192.168.0.50.



Configure the AP to enable the Telnet server function (the default

authentication username is admin, password is password, case

sensitive). You can remotely manage and maintain the AP through

Telnet.

Log into the AP

To Log into the AP after you determine its IP address, follows these steps:

1) Connect the AP and PC, and ensure that the PC and AP can communicate

with each other properly.

2) Launch your PC’s web browser. In the address bar, enter your AP’s IP

address and press Enter.

3) At the AP Login Screen, type the user name and password, and the

verification code, select the language (English and Chinese are supported at

present), and click Login. The default username and password are

case-sensitive:

xiii



Username: admin



Password: password

Converting your Managed AP (FIT) to a Stand-alone AP (FAT)

If you plan to run this AP in stand-alone mode, without a wireless controller, go to the

web page at http://www.3com.com to get the FAT firmware and instructions.

Converting your Stand-alone AP (FAT) to a Managed AP (FIT)

If you plan to run this AP in Managed AP mode with a wireless controller, go to the web

page http://www.3com.com to get the instructions.

Table of Contents

A Regulatory Compliance Information .................................................................... E-1

Regulatory compliance standards ....................................................................... E-1

Support Antennas & Accessories information ..................................................... E-1

EU Compliance information ................................................................................ E-1

CE Marking ................................................................................................ E-1

EU Country Restriction in 2.4GHz band ..................................................... E-5

EU Country Restriction in 5GHz band ........................................................ E-5

WEEE Directive–2002/96/EC ..................................................................... E-6

USA Compliance information .............................................................................. E-6

US Federal Communications Commission statement ................................ E-6

RF Requirements ....................................................................................... E-7

Antennas .................................................................................................... E-7

Industry Canada .................................................................................................. E-8

RF Compliance .......................................................................................... E-8

Brazil RF Compliance ......................................................................................... E-9

Korea RF Compliance ......................................................................................... E-9

Taiwan regulatory statement ............................................................................... E-9

E-1

Appendix E Regulatory Compliance Information

Regulatory compliance standards

Table1 Regulatory compliance standards

Discipline Standards

EMC & RF

FCC Part 15.207 & 15.209 & 15.247& 15.205 & 15.407

FCC Bulletin OET-65C

IC RSS 210

ETSI EN 300 328

ETSI EN 301 893

EN 60601-1-2

EN 61000-3-2

EN 61000-3-3

ETSI EN 301 489-1

ETSI EN 301 489-17

Safety

UL 60950-1

CAN/CSA C22.2 No 60950-1

IEC 60950-1

EN 60950-1

Support Antennas & Accessories information

This product can only be used with the supplied antenna(s).

This product does not contain any user serviceable components. Any unauthorized

product changes or modifications will invalidate the warranty and all applicable

regulatory certifications and approvals.

EU Compliance information

CE Marking

Page is loading ...

3com WL-607 Quick Installation Manual

Brand: 3com

Model: WL-607

Category: WLAN access points

Type: Quick Installation Manual

This manual is also suitable for

Download PDF

report

3com WL-607 Quick Installation Manual

This manual is also suitable for

3com WL-607 Quick Installation Manual

Related papers

Other documents