ClimateMaster ATA32H01 Install Manual

ClimateMaster
Brand
ClimateMaster
Model
ATA32H01
Category
Space heaters
Type
Install Manual
69-1310-1
Installer Setup
Number
(Press i key
Factory Setting
Other Choices
(Press ▲ or ▼ key to change)
Actual
Select
to change)
Display Description Display Description
Setting
Not used. 01 thru 02 — — — — —
Number of
compressor
stages.
03 02 Two compressor stages
or two-speed
compressor.
01 Single stage or single
compressor systems.
Heating cycle
rate.
05 — Not used. 03, 06
or 09
03—3 cph used for stage 1
heat pump systems.
—
06 06 Auxiliary heat. 06—6 cph used for
conventional systems.
07 06 Emergency heat. 09—9 cph used for electric
heat systems.
Not used. 08 thru 11 — — — — —
Changeover. 12 00 Automatic changeover. 01 00—Manual changeover.
Not used. 13 — — — — —
Degree
temperature
display.
14 00 Temperature is
displayed in °F.
01 Temperature is displayed
in °C
Not used. 15 thru 18 — — — — —
Extended fan
operation in
heating.
19 01 Fan operation is
extended 90 seconds
after the call for heat
ends.
00 No extended fan operation
after the call for heat ends.
Extended fan
operation in
cooling.
20 01 Fan operation is
extended 90 seconds
after the call for cool
ends.
00 No extended fan operation
after the call for cool ends.
Not used. 21 thru 23 — — — — —
Outdoor
temperature
display.
24 00 No outdoor temperature
is displayed.
01 Outdoor temperature is
displayed. Needs a
C7089B1000 Outdoor
Sensor to operate.
Not used. 25 thru 28 — — — — —
INSTALLATION INSTRUCTIONS
®U.S. Registered Trademark
ATA32H01
Microelectronic Heat Pump Thermostat
T8511M1028
Use form 69-1265 except use Table 2 and the hookup diagrams that follow.
Table 2. Thermostat Installer Setup Options.
(continued)
69-1310—1
2
ATA32H01
MICROELECTRONIC HEAT PUMP THERMOSTAT
Installer Setup
Number
(Press i key
Factory Setting
Other Choices
(Press ▲ or ▼ key to change)
Actual
Select
to change)
Display Description Display Description
Setting
O/B terminal
energized in
heating or
cooling.
29 00 O/B terminal is
energized for reversing
valve in cooling.
01 O/B terminal is energized for
reversing valve in heating.
Not used. 30 thru 32 — — — — —
Minimum off-
time for the
compressor.
33 00 No mnimum off-time for
the compressor.
00, 01,
02, 03,
04, or
05
Minimum number of minutes
(0 thru 5) the compressor
will be off between calls for
the compressor.
Heating
setpoint range
stop.
34 80 Heating setpoint can be
set no higher than 80°F.
40 thru
90
Number can be set
anywhere between 40 and
90 in 1°F increments.
Cooling
setpoint range
stop.
35 60 Cooling setpoint can be
set no lower than 60°F.
45 thru
99
Number can be set
anywhere between 45 and
99 in 1°F increments.
Not used. 36 — — — — —
Temperature
display
adjustment.
37 00 No difference in
displayed temperature
and actual room
temperature.
-3 thru
03
01—Display adjusts to 1°F
higher than actual room
temperature.
02—Display adjusts to 2°F
higher than actual room
temperature.
03—Display adjusts to 3°F
higher than actual room
temperature.
-1—Display adjusts to 1°F
lower than actual room
temperature.
-2—Display adjusts to 2°F
lower than actual room
temperature.
-3—Display adjusts to 3°F
lower than actual room
temperature.
Table 2. Thermostat Installer Setup Options (continued).
69-1310—1
3
ATA32H01
MICROELECTRONIC HEAT PUMP THERMOSTAT
R C Y1
Y2
Y2
W3
E
T8511M
DXM TERMINALS
O/B
G X1
R C Y1
W1
O/W2
G AL1
M14303
FACTORY INSTALLED JUMPER.
1
1
R C Y1
W3
E
T8511M
CXM TERMINALS
O/B
G X1
R C Y
W O
G AL1
1
69-1310—1 G.H. Rev. 5-99 Printed in Taiwan R.O.C.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ClimateMaster ATA32H01 Install Manual

ClimateMaster
Brand
ClimateMaster
Model
ATA32H01
Category
Space heaters
Type
Install Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents