Honeywell t8624d User manual

Brand: Honeywell

Model: t8624d

Category: Thermostats

Type: User manual

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69-1412-1

T8624D Chronotherm

Deluxe Programmable

Multistage Thermostats

APPLICATION

The T8624D Chronotherm® IV Deluxe Programmable

Multistage Thermostats provides electronic control of 24

Vac single-zone multistage systems.

Refer to Table 1 for a general description of the

thermostats. All T8624 thermostats require a common

wire to supply power.

Table 1. Description of T8624 Thermostats.

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of properly.

Contact your local waste management authority

for instructions regarding recycling and the

proper disposal of the old control.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

the instructions can damage the product or cause

a hazardous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions

to check out the product operation.

Location

Install the thermostat about 1.5m (5 ft) above the floor in

an area with good air circulation at average temperature.

See Fig. 1.

Do not install the thermostat where it can be affected by:

— drafts, or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

T8624 Changeover System Selection

Fan

Selection Comments

D Automatic Heat-Off-Cool-Auto On-Auto System and fan selections are done by keyboard.

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

69-1412—1 2

Wallplate Installation

The thermostat can be mounted horizontally on the wall

or on a 2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.

Position wallplate horizontally on the wall or on a

2 in. x 4 in. (50.8 mm x 101.6) mm wiring box.

Fig. 1. Typical location of thermostat.

1. Position and level the wallplate (for appearance

only). The thermostat will function correctly even

when not level.

2. Use a pencil to mark the mounting holes. See Fig.

3. Remove the wallplate from the wall and drill two

3/16 inch (76 mm) holes in the wall (if drywall) as

marked. For firmer material such as plaster, drill

two 7/32 inch (5.56 mm) holes. Gently tap anchors

(provided) into the drilled holes until flush with the

wall.

4. Position the wallplate over the holes, pulling wires

through the wiring opening.

5. Loosely insert the mounting screws into the holes.

6. Tighten mounting screws.

Fig. 2. Mounting the wallplate.

WIRING

All wiring must comply with local electrical codes and

ordinances. Refer to Fig. 3 for typical hookup. A letter

code is located near each terminal for identification.

CAUTION

Electrical Shock Hazard.

Can cause electrical shock or equipment

damage.

Disconnect power before beginning wiring.

1. Loosen the terminal screws on the wallplate and

connect the system wires. See Fig. 4.

IMPORTANT

Use 18 gauge, color-coded thermostat cable for

proper wiring.

2. Securely tighten each terminal screw.

3. Push excess wire back into the hole.

4. Plug the hole with nonflammable insulation to pre-

vent drafts from affecting the thermostat.

1.5 METERS

(5 FEET)

YES

M10856

WIRES

THROUGH WALL

WALL

MOUNTING

HOLES

M15044

MOUNTING

SCREWS

WALL

ANCHORS (2)

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

3 69-1412—1

Fig. 3. Typical hookup of T8624D

in a heat pump system.

Fig. 4. Correct wiring technique.

Mounting Thermostat

1. Engage tabs at the top of the thermostat and wall-

plate. See Fig. 5.

2. Press lower edge of case to close and latch.

NOTE: To remove the thermostat from the wall, first pull

out at the bottom of the thermostat; remove top

last.

Fig. 5. Mounting thermostat on wallplate.

(HOT)

M11309

FAN

RELAY

Y1 G C

THERMOSTAT

HEAT

RELAY

RW1

(HOT)

COMPRESSOR

CONTACTOR 1

COMPRESSOR

CONTACTOR 2

HEATING

TRANSFORMER

COOLING

TRANSFORMER

HEAT

RELAY

OTB

HEAT

DAMPER

OUTDOOR

SENSOR

COOL

DAMPER

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

JUMPER RC TERMINAL TO R TERMINAL WHEN INSTALLED ON A

ONE TRANSFORMER SYSTEM.

CAN BE USED FOR CHANGEOVER VALVE ON HEAT

PUMP SYSTEMS.

M4826

FOR WRAPAROUND

INSERTION STRIP

7/16 IN. (11 MM).

FOR STRAIGHT INSERTION

STRIP 5/16 IN. (8 MM).

M14628

PRESS LOWER

EDGE OF CASE

TO LATCH.

ENGAGE TABS

AT TOP OF

THERMOSTAT

AND WALLPLATE.

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

69-1412—1 4

Fig. 6. T8624D key locations and descriptions.

Using Thermostat Keys

The thermostat keys are used to:

• set current day and time,

• program times and setpoints for heating and cooling,

• temporarily override program temperatures,

• display present setting,

• configure Installer Setup,

• check System Test,

• display outdoor temperature (select models),

• set the system operation,

• set the fan operation.

See Fig. 6 for the location of the keys.

SETTINGS

System and Fan Settings

The system default setting is Heat and the fan default

setting is Auto. Use the System and Fan keys to change

the settings. See Fig. 7. The fan settings can be set for

each program period individually. The system selection is

for all the program periods.

System settings control the thermostat operation as

follows:

Heat: The thermostat controls the heating.

Off: Both the heating and cooling are off.

Cool: The thermostat controls the cooling.

Auto: The thermostat automatically changes between

heating and cooling operation, depending on the

indoor temperature.

Fan settings control the system fan as follows:

On: Fan operates continuously.

Auto: Fan operates with equipment.

Fig. 7. T8624D System and Fan key locations.

NOTE: Always press the keys with your fingertip or

similar blunt tool. Sharp instruments like a pen

or pencil point can damage the keyboard.

Temperature Settings

Refer to Table 2 for the default program. If the daytime

energy savings period is not used, press the period key

(Leave or Return) until the time is blank. The fan setting

feature is available on select thermostat models. See

Owners Guide, form number 69-0940, for complete

instructions on changing the program.

Table 2. Default Program Settings.

M14624

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time

Wake

Leave

Return Sleep

Day

Heat/Cool

Settings

Daylight

Time

Copy

INCREASE

TEMPERATURE

SETTING OR SCROLL

FORWARD THROUGH

INSTALLER SETUP OPTIONS

DECREASE TEMPERATURE

SETTING OR SCROLL

BACKWARD THROUGH

INSTALLER SETUP OPTIONS

DISPLAY INFORMATION

SUCH AS PRESENT

SETTINGS AND OUTDOOR

TEMPERATURE

RETURN TO

NORMAL

OPERATIONS

ENTER

INDEFINITE

OR TIMED

HOLD MODE

SET CURRENT

DAY AND TIME

SET CURRENT OR

PROGRAM DAY

CHANGE BETWEEN

DAYLIGHT SAVINGS

AND STANDARD TIME

INCREASE TIME SETTING

OR SCROLL FORWARD

THROUGH INSTALLER SETUP

ND SYSTEM TEST

DECREASE TIME SETTING OR

SCROLL BACKWARD THROUGH

INSTALLER SETUP AND SYSTEM TEST

COPY ONE PROGRAMMED

DAY TO ANOTHER DAY

SET WAKE TIMES

AND SETPOINTS

CHANGE BETWEEN

HEATING AND COOLING

SETPOINTS

SET LEAVE TIMES

AND SETPOINTS

SET RETURN TIMES

AND SETPOINTS

SET SLEEP TIMES

AND SETPOINTS

SELECT SYSTEM

OPERATION

SELECT FAN

OPERATION

Period Time

Heat

Setpoint

Cool

Setpoint

Fan

Setting

Wake 6:00 AM 70°F

(21°C)

78°F

(25.5°C)

Auto

Leave 8:00 AM 62°F

(16.5°C)

85°F

(29.5°C)

Auto

Return 6:00 PM 70°F

(21°C)

78°F

(25.5°C)

Auto

Sleep 10:00 PM 62°F

(16.5°C)

82°F

(28°C)

Auto

M14625

Hold Temp

Run

Program

Copy

Daylight

Time

Set Current

Day/Time

System Fan

Time Set Program

Day

System

Fan

Wake

Leave

Return

Sleep

Heat/Cool

Settings

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

5 69-1412—1

INSTALLER SETUP

NOTE: For most applications, the thermostat factory-

settings will not need to be changed. Review

the factory settings in Table 2 and if no changes

are necessary, go to the Installer System Test

section.

The Installer Setup is used to customize the thermostat

to specific systems. Some of the options include

temperature display, changeover, and outdoor

temperature display. Installer Setup numbers are listed in

Table 3. The table includes all the configuration options

and the factory settings for the T8624.

A combination of key presses are required to use the

Installer Setup feature.

— To enter the installer setup, press and hold the

information i key with the increase ! and

decrease " keys until the first number is displayed.

All display segments appear for approximately three

seconds before the number is displayed. See Fig. 8

and 9.

— To advance to the next Installer Setup, press the

Time ∆ key.

— To change a setting, use the increase ! or

decrease " key.

— To scroll the Installer Setup numbers backward, press

the Time ∇ key.

— To exit the Installer Setup, press Run Program.

Fig. 8. Display of all LCD segments..

Fig. 9. Display of Installer Setup number and setting.

IMPORTANT

Only configurable numbers are shown on the

device. Example: If thermostat does not have a

System key, Installer Setup Number 12 will not

be displayed. Review Table 3 factory settings

and mark any desired changes in the Actual

Setting column. When Installer Setup is

complete, review the settings to confirm that

they match the system.

M14559

Aux Ht

Set Day/TimeSet Program

Mon

Wake Leave Return Sleep

door

Room

Filter

Wait

Fan

Em H

eat

Hold for

Heat

Cool

Repl Batt

Recovery

DST

Tue Wed Thu Fri Sat Sun

Days

Temporary Setting

Em Ht

M14618

INSTALLER SETUP

NUMBER DISPLAY

(COLUMN 2 OF TABLE 3)

FACTORY SETTING OR OTHER

CHOICE DISPLAY (COLUMN 3

OR 5 OF TABLE 3)

Table 3. Thermostat Installer Setup Options.

Select

Installer Setup

Number (Press

Time ∆ key to

change)

Factory Setting

Other Choices

(Press ! or " key to change)

Actual

SettingDisplay Description Display Description

Not Used. 1 — — — — —

Fan operation. 2 0 Conventional

applications where

equipment controls

fan operation in

heat mode

1 Heat pump and electric heat

applications where

thermostat controls fan

operation in heat mode

Not Used. 3 — — — — —

Heating cycle

rate.

4 6 Stage 1 — 6—6 cph is fixed for stage 1.

5 Stage 2 3 or 9 3—3 cph

6—6 cph factory setting for

all stages of system

9—9 cph used for electric

heat

Not Used. 6 thru 11 — — — — —

System setting

adjustment

12 1 Manual

changeover

0 or 2 0—Auto changeover

2—Fixed auto changeover

a The cycle rate for the last stage of heat is adjustable with 6 cph as the factory setting.

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

69-1412—1 6

Adaptive

Intelligent

Recovery™

control.

13 0 Adaptive Intelligent

Recovery™

control is activated

(system starts

early so setpoint is

reached by start of

program period).

1 Conventional recovery

(system starts recovery at

programmed time).

—

Degree

temperature

display

14 0 Temperature is

displayed in °F

1 Temperature is displayed

in °C

Not Used. 15 — — — — —

Clock format. 16 0 12-hour clock

format.

1 24-hour clock format.

Not Used. 17 thru 18 — — — — —

Extended fan

operation in

heating

19 0 No extended fan

operation after the

call for heat ends.

1 Fan operation is extended

90 seconds after the call for

heat ends.

Extended fan

operation in

cooling

20 0 No extended fan

operation after the

call for cool ends.

1 Fan operation is extended

90 seconds after the call for

cool ends.

Not Used. 21 thru 23 — — — — —

Outdoor

temperature

display (models

with OT

terminals).

24 0 No outdoor

temperature is

displayed.

1 Outdoor temperature is

displayed. Needs a

C7089B1000 Outdoor

Temperature Sensor to

operate.

Not Used. 25 thru 29 — — — — —

Deadband 30 3 Heating and

cooling setpoints

can be set no

closer than 3°F

(1.5°C).

4 thru 10 Heating and cooling

setpoints can be set no

closer than the chosen

value:

4—4°F (2°C)

5—5°F (2.5°C)

6—6°F (3°C)

7—7°F (3.5°C)

8—8°F (4°C)

9—9°F (4.5°C)

10—10°F (5°C)

Not Used. 31 and 32 — — — — —

Minimum off

time for the

compressor.

33 5 5 minutes

minimum off time

for the

compressor.

0 thru 4 Minimum number of minutes

(0 thru 5) the compressor

will be off between calls for

the compressor.

Temperature

range stops in

heating.

34 90 Highest setpoint

setting for heating.

40 to 89 Temperature range (1°F

increments) of heating

setpoint settings.

Temperature

range stops in

cooling.

35 45 Lowest setpoint

setting for cooling.

46 to 99 Temperature range (1°F

increments) of cooling

setpoint settings

Not Used. 36 — — — — —

Table 3. Thermostat Installer Setup Options. (Continued)

Select

Installer Setup

Number (Press

Time ∆ key to

change)

Factory Setting

Other Choices

(Press ! or " key to change)

Actual

SettingDisplay Description Display Description

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

7 69-1412—1

IMPORTANT

Review the settings to confirm that they match

the system. Press Run Program to exit the

Installer Setup. The thermostat has saved the

Installer Setup changes and initiated a reset in

order to operate using the new settings. Be sure

to set the current day and time immediately.

Setting Current Day and Time

1. Press Set Current Day/Time.

NOTE: On initial powerup or after an extended power

loss, 1:00 pm flashes on the display until a key

is pressed.

2. Press Day until the current day is displayed.

NOTE: Sun=Sunday, Mon=Monday,

Tue=Tuesday, Wed=Wednesday,

Thu=Thursday, Fri=Friday, Sat=Saturday.

3. Press Time ∆ or Time ∇ until the current time is dis-

played.

NOTE: Tapping the Set Current Day/Time changes the

time in one-hour increments.

Temperature

display

adjustment.

37 0 No difference in

displayed

temperature and

actual room

temperature.

-3 thru +3 1—Display adjusts to 1°F

higher than actual room

temperature.

2—Display adjusts to 2°F

higher than actual room

temperature.

3—Display adjusts to 3°F

higher than actual room

temperature.

-1—Display adjusts to 1°F

lower than actual room

temperature.

-2—Display adjusts to 2°F

lower than actual room

temperature.

-3—Display adjusts to 3°F

lower than actual room

temperature.

Furnace Air

Filter Timer.

43 2 30 days (System

run time).

0, 1, 3, 4 0 – Off

1 – 10 days

3 – 60 days

4 – 120 days

(Time counted when heat,

cool or fan is running.)

Humidifier Pad

Monitor.

44 0 Off 1, 2, 3 1 – 90 days

2 – 180 days

3 – 365 days

(Time counted by calendar

days in heat mode.)

Ultraviolet Air

Treatment (UV)

System Lamp

Monitor.

45 0 Off 1 1 – 365 days

(Time counted by calendar

days in any mode.)

Table 3. Thermostat Installer Setup Options. (Continued)

Select

Installer Setup

Number (Press

Time ∆ key to

change)

Factory Setting

Other Choices

(Press ! or " key to change)

Actual

SettingDisplay Description Display Description

M14619

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time

Set Current

Day/Time

Wake

Leave

Return Sleep

Day

Heat/Cool

Settings

Daylight

Time

Copy

Set Day/Time

Mon

M14620

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time

Wake

Leave

Return Sleep

Day

Heat/Cool

Settings

Daylight

Time

Copy

Set Day/Time

Tue

M14621

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time

Wake

Leave

Return Sleep

Day

Time

Heat/Cool

Settings

Daylight

Time

Copy

Set Day/Time

Tue

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

69-1412—1 8

NOTE: If the current time is Daylight Savings Time,

press Daylight Time until DST is displayed.

4. Press Run Program.

Viewing or Resetting Timer Settings

When the thermostat activates a timer, the thermostat

flashes Filter until the timer resets.

1. Reset the timer by pressing the i key until the

expired timer is displayed.

2. Press the Time skey to reset the timer.

3. Press the Run Program key.

NOTE: You can view the number of days remaining at

any time by pressing the i key three or four

times. If more than one timer is active, all active

timers show sequentially when pressing the

i key several times.

INSTALLER SYSTEM TEST

Use the Installer System Test to check the thermostat

operation. Refer to Table 4 for a list of the available

system tests.

To start the system test:

CAUTION

The minimum off time for compressors is

bypassed during the Installer System Test.

Equipment damage can occur if the compressor

is cycled too quickly.

Press and hold the increase ! and decrease " keys at

the same time until 10 appears. All segments of the

display will be displayed before the 10 appears.

See Fig. 10 and 11.

Table 4. Tests Available In Installer System Test.

Fig. 10. Display of all the segments of the LCD.

Fig. 11. Display of test number.

Refer to Table 5 for the directions and results of the

specific tests.

Press Time ∆ to advance to the next test and Time ∇ to

go back to the previous test. Press Run Program to exit

the system test

M14622

Time Set Program

System Fan

Run

Program

Hold Temp

Set Current

Day/Time

Wake

Leave

Return Sleep

Day

Heat/Cool

Settings

Daylight

Time

Daylight

Time

Copy

Set Day/Time

DST

Tue

M14623

Time Set Program

System Fan

Run

Program

Run

Program

Hold Temp

Set Current

Day/Time

Wake

Leave

Return Sleep

Day

Heat/Cool

Settings

Daylight

Time

Copy

Wake

Room

System

Fan

Heat

Auto

DST

Tue

M20243

Filter

Days

M20244

Filter

Days

Test Number System Test Description

10-19 Heating equipment can be turned on

and off.

30-39 Cooling equipment can be turned on

and off.

40-49 Fan equipment can be turned on and

off.

60 0 to 60 19 Keyboard keys test.

70-79 Thermostat information including date

code and software versions are

displayed.

M14559

Aux Ht

Set Day/TimeSet Program

Mon

Wake Leave Return Sleep

door

Room

Filter

Wait

Fan

Em H

eat

Hold for

Heat

Cool

Repl Batt

Recovery

DST

Tue Wed Thu Fri Sat Sun

Days

Temporary Setting

Em Ht

M14612

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

9 69-1412—1

Table 5. Installer System Test Options.

NOTE: Press any key and the displayed numbers will change. Press Time ∇ to go to the previous test and Time ∆ to

go to the next test. The Run Program key will not exit this test. Press Time ∆ or Time ∇ and then the

Run Program key to exit.

Keys to

Press

Test

Number Description

Heating Equipment System Test

Time ∆ 10 Enter heating equipment System Test.

11 Stage-one heat comes on. The system fan is also energized.

12 Stage-two heat comes on. Stage-one heat and system fan remain on.

11 Stage-two heat turns off.

10 Stage-one heat and system fan turn off.

Cooling Equipment System Test

Time ∆ 30 Change from heating to cooling equipment System Test.

31 Stage-one cool and system fan come on.

32 Stage-two cool comes on. Stage-one cool and system fan remain on.

31 Stage-two cool turns off.

30 Stage-one cool and system fan turn off.

Fan Equipment System Test

Time ∆ 40 Change from cooling to fan equipment System Test.

41 Fan comes on.

40 Fan turns off.

Key Operation System Test

Time ∆ 60 Change from fan to key operation System Test.

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

69-1412—1 10

THERMOSTAT INFORMATION

1. Press the Time ∆ key to access the thermostat

information.

2. Press the increase ! key to display the production

date code. The first two large digits are the month

and the third digit is the last digit of the year (Exam-

ple: 027 = February 1997).

3. Press the increase ! key again to display the soft-

ware identification code. (Example: 02 = software

ID code 2)

4. Press the increase ! key again to display the soft-

ware revision number (Example: 001 = Revision

number 1).

5. Press the increase ! key again to display the

EEPROM identification code. (Example: 314 =

EEPROM ID 314)

6. Press the Run Program key to exit the system test.

The system test times out after four minutes with-

out any key presses.

CHECKOUT

Outdoor Temperature Sensor

(Select Models)

Allow the outdoor temperature sensor to absorb the

outdoor air for a minimum of five minutes before taking a

reading.

M14613

M14614

M14615

M14616

M14617

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

11 69-1412—1

TROUBLESHOOTING GUIDE

Table 6. Troubleshooting Guide.

Symptom Possible Cause Action

Display will not

come on.

Thermostat is not being

powered.

• Check for 24 Vac between R and C terminals.

— If missing 24 Vac:

— check if the circuit breaker is tripped—reset the circuit

breaker.

— check if the system fuse is blown—replace the fuse.

— check if the power switch on the HVAC equipment is in

the Off position—set to the On position.

— check wiring between thermostat and HVAC

equipment—replace any broken wires and tighten any

loose connections.

— If 24 Vac is present, proceed with troubleshooting

Temperature

display is incorrect.

Room temperature display has

been reconfigured.

Enter Installer Setup number 37 and reconfigure the display.

Thermostat is configured for °F

or °C display.

Enter Installer Setup number 14 and reconfigure the display.

Bad thermostat location. Relocate the thermostat.

Temperature

settings will not

change. (Example:

Cannot set the

heating higher or

the cooling lower.)

The upper or lower temperature

limits were reached.

Check the temperature setpoints:

• Heating limits are 40 to 90°F (7 to 31°C).

• Cooling limits are 48 to 99°F (9 to 37°C).

The setpoint temperature range

stops were configured.

Check Installer Setup numbers 34 and 35 and reconfigure the

setpoint stops.

Heating will not

come on.

No power to the thermostat. • Check for 24 Vac between R and W terminals.

— If missing 24 Vac:

— check if the circuit breaker is tripped—reset the circuit

breaker.

— check if the system fuse is blown—replace the fuse.

— check if the power switch on the HVAC equipment is in

the Off position—set to the On position.

— check wiring between thermostat and HVAC

equipment—replace any broken wires and tighten any

loose connections.

— If 24 Vac is present, proceed with troubleshooting.

Thermostat minimum off time is

activated.

Wait up to five minutes for the system to respond.

System selection is not set to

Heat.

Set system selection to Heat.

Heating setpoint is below room

temperature.

Check heating setpoint. Set heating setpoint to desired

temperature.

Cooling will not

come on.

No power to the thermostat. • Check for 24 Vac between R or RC.

— If missing 24 Vac:

— check if the circuit breaker is tripped—reset the circuit

breaker.

— check if the system fuse is blown—replace the fuse.

— check if the power switch on the HVAC equipment is in

the Off position—set to the On position.

— check wiring between thermostat and HVAC

equipment—replace any broken wires and tighten any

loose connections.

— If 24 Vac is present, proceed with troubleshooting.

Thermostat minimum off time is

activated.

• Wait up to five minutes for the system to respond.

• Enter Installer Setup number 33. Reconfigure minimum off

time (if required).

System selection is not set to

Cool.

Set system selection to Cool.

Cool setpoint is above room

temperature.

Check cooling setpoint. Set cooling setpoint to desired

temperature.

69-1412—1 G.H. Rev. 12-02 www.honeywell.com/yourhome

T8624D CHRONOTHERM

IV DELUXE PROGRAMMABLE MULTISTAGE THERMOSTATS

Automation and Control Solutions

Honeywell Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North 35 Dynamic Drive

Golden Valley, MN 55422 Scarborough, Ontario

M1V 4Z9

System on indicator

(flame=heat,

snowflake=cool) is

displayed, but no

warm or cool air is

coming from the

registers.

Heating or cooling equipment is

not operating.

Verify operation of heating or cooling equipment in self-test.

Outdoor tempera-

ture not displayed

Option not activated. Enter Installer Setup number 24 and set to 1. Thermostat must

have OT terminals and a C7089B1000 installed.

Outdoor

temperature

display is incorrect

Outdoor sensor is connected

incorrectly.

Refer to C7089B1000 Installation Instructions and check wiring

between the thermostat and sensor.

Wrong sensor. Replace sensor with C7089B1000 Sensor.

Select models.

Table 6. Troubleshooting Guide. (Continued)

Symptom Possible Cause Action

Honeywell t8624d User manual

Brand: Honeywell

Model: t8624d

Category: Thermostats

Type: User manual

Download PDF

report

Honeywell t8624d User manual

Honeywell t8624d User manual

Related papers

Other documents