DFI ADN553 User manual

DFI
Brand
DFI
Model
ADN553
Type
User manual

This manual is also suitable for

ADN553
Embedded 3.5" SBC
User’s Manual
© July 17, 2023 DFI Inc.
2
User's Manual | ADN553
Copyright
This publication contains information that is protected by copyright. No part of it may be repro-
duced in any form or by any means or used to make any transformation/adaptation without the
prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this docu-
ment. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions or
changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2023. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for com-
pliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
3
User's Manual | ADN553
Table of Contents
Chapter 1 - Introduction................................................................................................................6
Specifications ......................................................................................................................... 6
Dimensions ............................................................................................................................. 8
Block Diagram ........................................................................................................................8
Chapter 2 - Hardware Installations ..............................................................................................9
Overview .................................................................................................................................. 9
Top View ...........................................................................................................................9
Bottom View.....................................................................................................................9
Jumper Settings ...................................................................................................................10
Panel Backlight Selection (DPJP1) .............................................................................10
Panel Inverter/Backlight Power Selection (DPJP2) ...................................................10
Panel VDD Power Jumper (DPJP3) ............................................................................11
Pin Assignment ....................................................................................................................12
System Fan (J10) ......................................................................................................... 12
Power Connector (CN11) .............................................................................................. 12
SATA Power (J1001) ................................................................................................... 13
LVDS Inverter Power (J1002) .......................................................................................13
Front Panel (J11) ........................................................................................................... 14
COM1 (TSJ1) .................................................................................................................14
DIO (J1000) .................................................................................................................... 15
Front Audio (AUJ1) ........................................................................................................15
USB2.0 (J3) ....................................................................................................................16
eSPI & UART Debug (J5) ...............................................................................................16
LVDS (DPCN1)................................................................................................................17
eDP (DPCN2) .................................................................................................................18
Expansion Slots .................................................................................................................... 19
Installing the M.2 Module .............................................................................................19
Installing the SO-DIMM Module ...................................................................................21
Installing the Heatsink .........................................................................................................23
Chapter 3 - BIOS Settings ...........................................................................................................24
Overview ...............................................................................................................................24
Main .......................................................................................................................................25
Advanced .............................................................................................................................25
RC ACPI Settings ...........................................................................................................26
CPU Configuration .........................................................................................................26
Power & Performance ...................................................................................................27
PCH-FW Configuration ..................................................................................................27
Trusted Computing ........................................................................................................28
NCT5525D Super IO Configuration ..............................................................................28
NCT5525D Super IO Configuration â–º Serial Port 1 Configuration ......................29
Hardware Monitor .......................................................................................................... 29
Hardware Monitor â–º Smart Fan Function ...........................................................30
Serial Port Console Redirection ..................................................................................30
Serial Port Console Redirection â–º Console Redirection Settings ........................31
Network Stack Configuration........................................................................................31
USB Power Control ........................................................................................................32
Chipset ..................................................................................................................................33
System Agent (SA) Configuration ................................................................................33
PCH-IO Configuration ....................................................................................................34
PCH-IO Configurationâ–º PCI Express Configuration .............................................34
PCH-IO Configurationâ–º SATA Configuration .......................................................35
PCH-IO Configurationâ–º HD Audio Configuration .................................................35
Security .................................................................................................................................36
Secure Boot ....................................................................................................................36
Boot .......................................................................................................................................37
Save & Exit ............................................................................................................................37
Updating the BIOS ................................................................................................................ 38
Notice: BIOS SPI ROM..........................................................................................................38
Appendix A- Mating Connectors ................................................................................................ 39
The Mating Connectors List ................................................................................................ 39
4
User's Manual | ADN553
About this Manual
This manual can be retrieved from the website.
The manual is subject to change and update without notice, and may be based on editions that
do not resemble your actual products. Please visit our website or contact our sales representa-
tives for the latest editions.
Warranty
1. Warranty does not cover damages or failures that arises from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper
installation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether
in or out of warranty. It must be returned to the purchase point, factory or authorized
service agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequential damages to
the product that has been modified or altered.
About this Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• 1 ADN553 Board
• 1 Heat Sink (Height: 29 mm)
Note: The items are subject to change in the developing stage. Note: The items are subject to change in the developing stage.
The product and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
5
User's Manual | ADN553
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you
are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, con-
tacts or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or
connectors by their ends.
Safety Precautions
• Use the correct DC / AC input voltage range.
• Unplug the power cord before removing the system chassis cover for installation or
servicing. After installation or servicing, cover the system chassis before plugging in
the power cord.
• There is danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent specifications of batteries recommend by
the manufacturer.
• Dispose of used batteries according to local ordinance.
• Keep this system away from humid environments.
• Make sure the system is placed or mounted correctly and stably to prevent the chance
of dropping or falling may cause damage.
• The openings on the system shall not be blocked and shall be kept in distance from
other objects to make sure of proper air ventilation to protect the system from over-
heating.
• Dress the cables, especially the power cord, so they will not be stepped on, in contact
with high temperature surfaces, or cause any tripping hazards.
• Do not place anything on top of the power cord. Use a power cord that has been ap-
proved for use with the system and is compliant with the voltage and current ranges
required by the system’s electrical specifications.
• If the system is to be unused or stored for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system is physically damaged.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground
the unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet
does not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the electricity outlet before cleaning. Use a damp cloth
for cleaning the surface. Do not use liquid or spray detergents for cleaning.
• Before connecting, make sure that the power supply voltage is correct. The device is
connected to a power outlet which should be grounded connection.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other
components. Perform the upgrade instruction procedures described at an ESD
workstation only. If such a station is not available, you can provide some ESD pro-
tection by wearing an antistatic wrist strap and attaching it to a metal part of the
system chassis. If a wrist strap is unavailable, establish and maintain contact with
the system chassis throughout any procedures requiring ESD protection.
The system may burn fingers while running.
Wait for 30 minutes to handle electronic parts after power off.
6
Chapter 1
INTRODUCTION
User's Manual | ADN553
Chapter 1 - Introduction
XSpecifications
SYSTEM
Processor
Intel® Atom® Alder Lake-N Processors, TDP up to 15W
Embedded
Intel Atom® x7425E, 4 cores, 6M Cache, up to 3.40 GHz, 12W
Intel Atom® x7211E, 2 cores, 6M Cache, up to 3.20 GHz, 6W
PC Client
Intel® Core™ i3-N305, 8 cores, 6M Cache, up to 3.80 GHz, 15W
Intel® Processor N200, 4 cores, 6M Cache, up to 3.70 GHz, 6W
Intel® Processor N97, 4 cores, 6M Cache, up to 3.60 GHz, 12W
Intel® Processor N50, 2 cores, 6M Cache, up to 3.40 GHz, 6W
Memory One 262-pin SODIMM up to 16GB
Single Channel DDR5 4800MHz
BIOS AMI SPI 256Mbit
GRAPHICS Controller Intel® UHD Graphics
Feature
OpenGL 4.6, Direct X 12.1, OpenCL 3.0
HW Decode: HEVC, VP9, AV1, AVC
HW Encode: HEVC, VP9, AVC
Display
1 x HDMI
HDMI: resolution up to 4096x2160@24Hz
1 x Type-C DP Alt. Mode
DP: resolution up to 3840x2160 @60Hz
1 x LVDS/eDP
LVDS: dual channel 24-bit, resolution up to 1920x1200@60Hz
eDP: resolution up to 4096x2160 @60Hz
Triple Display HDMI + Type-C DP Alt. Mode + LVDS/eDP
EXPANSION
Interface
1 x M.2 M key 2280/2242 (PCIe Gen3 x1/SATA3.0)
1 x M.2 B key 3052/3042 (USB3.0/USB2.0, optional PCIe x1)
1 x M.2 E key 2230 (USB/PCIe x1, support CNVi)
1 x SIM slot for 4G/5G
AUDIO Audio Codec Realtek ALC888S
ETHERNET Controller 3 x Intel® I226LM/V(10/100/1000/2500Mbps).
LAN3 option with M.2 3052 PCIe x1.
REAR I/O Ethernet 3 x 2.5GbE (RJ-45)
USB 4 x USB 3.2 Gen2
2 x USB 2.0
Display
1 x HDMI
1 x Type-C DP Alt. Mode
1 x LVDS/eDP
7
Chapter 1
INTRODUCTION
User's Manual | ADN553
INTERNAL I/O
Serial 1 x RS-232/422/485 (2.0mm pitch)
USB 2 x USB 2.0 (2.0mm pitch)
Display 1 x LVDS LCD Panel Connector
1 x LCD/Inverter Power
Audio 1 x Audio (Line-out/Mic-in)
SATA 1 x SATA 3.0 (up to 6Gb/s)
1 x SATA Power
DIO 1 x 8-bit DIO
WATCHDOG TIMER Output &
Interval System Reset, Programmable via Software from 1 to 255 Seconds
SECURITY TPM dTPM 2.0
POWER
Type Wide Range 9~36V DC
Connector
Right Angle Connector (4-pin)
DC-in Jack (available upon request)
Vertical Type Connector (4-pin) (available upon request)
Consumption TBD
RTC Battery CR2032 Coin Cell
OS SUPPORT OS Support
(UEFI Only)
Windows 10 IoT Enterprise (64-bit)
Linux
MECHANISM
Dimensions 3.5" SBC Form Factor
Height
PCB: 1.6mm
Top Side: 15mm
Bottom Side: 4mm
ENVIRONMENT
Temperature Operating: -5 to 65°C
Humidity Operating: 5 to 90% RH
MTBF TBD
STANDARDS AND
CERTIFICATIONS Certifications CE, FCC Class B, RoHS
8
Chapter 1
INTRODUCTION
User's Manual | ADN553
XDimensions XBlock Diagram
9
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
Chapter 2 - Hardware Installations
XOverview
Top View
© July 06, 2023 DFI Inc.
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
12345 6
78
9
10
11
12
13
14
15
16
17
18
19 20
21
22
24
23
75
1
75
1
22 28
1521
14
8
1
7
C
A
37
48
25
36
24
13
1 12
DE
59
A
1
6
31
S1
D1 S2
D2
D2
S2
D1
S1
31 40
21
20 11
1
10
31
40
21
30
20
10
1
6
20
15
5
1
GS
D
GS
D
64
48 33
32
17
16
1
2
2
2 2
23
1
3
1
1
3
2
2
3
1
2
3
1
2
3
1
2
3
1
1
3
2
B
EC
B
E
C
B E
C
54
3
1
5
43
1
1 3
45
4
7
4
1
5
1
4
1
58
1
1
1
1
11
11
1
1
1
1
5
13
1
10
4
9
9
4
1
13
1
9
25
17
43 56
2942
28 15
1
14
43 56
42
28
1
14
43 56
29
42
28
15
1
14
56
29
42
28 15
1
14
CA
C
A
A
C
A
C
C
A
C
A
A
C
A
C
A
C
C
A
C
A
A
C
A
C
A C
C
A
C
A
AC
A
C
C
ACA
C A
5
4
1
3
1
51
5
1
51
5
1 3
45
1 3
45
1 3
45
1
3
45
13
4
5
1
3
4
5
13
45
1
4
5
5 4
3
1
5
4
1
5
4
3
1
54
1
5
4 3
1
54
31
54
3
1
5 4
1
13
4 5
5
1
5
1
5
1
1
5
1
5
3
4
6
1
3 4
6
1
3
4
61
4
6
1
3
4
6
1
3
4
61
3
46
1
3
4
6
1
3
4
6
1
1
6
4
3
1
64
3
4
6
1
1
4
3
3
4
1
4
6
1
34
6
1
U1003 U1004
U8012
LED1
U8006
U1
X2
LI1
Q17
Q1
Q8
U14
TSU1
FB8000
U8004
Q1000
Q5
SOU1
D1007
D1006
D7
D4
AUD1
AUD3
D2
D6
Q14
Q13
Q8002
X1
X3X4
X5
U6
U41
U15
U8003
U40
U38
U12
UBD12
U7
UBD2UBD1
UBD3 UBD4
UBD6
UBD5
VR8000
U8001
U39
DPU1
U9
U11
U13
D8000
AUC19
AUC20
SC3
F2
F1
DPF2
D29
SC8003
SC8004
SC8000
SC8002
SC8001
SC2
SC8005
SC8006
SC1
R8042
R8026
R692
R8068
R336
LC8004
LC8010
LC8001
LC8002
LC3
LC4
LC5
D8011
D8005
D8004
D8003
D8002
D8001
C271
C24
C8081
C61
C8136
C8005
J10
Q8005
Q8004
Q8006
Q8003
U1002
U1001
U1000
U36
U31
DPU2
U32
U33
U25
U20
U23
U26
U27
U21
U24
U22
U29
TSQ1
Q8009
Q8010
Q8007
Q8008
DPQ7
Q11
DPQ6
M2Q1
DPQ5
Q12
Q10
Q4
Q3
Q16
DPQ1
Q6
Q15
Q8019
Q8017
Q8011
MADE IN TAIWAN REV.2
ADN553
SYS_FAN
1
25
Bottom View
1
21
2
22
3
23
4
24
5
25
6
7
8
9
10
11
12
14
15
16
17
18
19
20
13
Power Connector
2.5G LAN1
2.5G LAN2
2.5G LAN3
USB3.2 Gen2
â–²USB3.2 Gen2
â–¼USB Type-C
HDMI
RTC Battery
SATA Power
SATA 3.0
USB2.0 6/7
DIO
eSPI & UART Debug
COM1
Front Panel
SPI ROM
eDP
LVDS Inverter Power
Panel Backlight Selection
Panel Inverter/Backlight Power Selection
Panel VDD Power Jumper
LVDS
SIM Card Slot
Front Audio
System Fan
10
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
XJumper Settings
Panel Backlight Selection (DPJP1) Panel Inverter/Backlight Power Selection (DPJP2)
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
11
î‚„1-2 On: 3.3V (default) î‚„1-2 On: 12V (default)
11
î‚„2-3 On: 5V î‚„2-3 On: 5V
11
11
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
Panel VDD Power Jumper (DPJP3)
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
î‚„1-2 On: 12V î‚„3-4 On: 5V î‚„5-6 On: 3.3V (default)
1
2
65
6 6 6
5 5 5
2 2 2
1 1 1
12
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
System Fan (J10) Power Connector (CN11)
75
1
75
1
22 28
1521
14
8
1
7
C
A
37
48
25
36
24
13
1 12
DE
59
A
1
6
31
S1
D1 S2
D2
D2
S2
D1
S1
31 40
21
20 11
1
10
31
40
21
30
20
10
1
6
20
15
5
1
GS
D
GS
D
64
48 33
32
17
16
1
2
2
2 2
23
1
3
1
1
3
2
2
3
1
2
3
1
2
3
1
2
3
1
1
3
2
B
EC
B
E
C
B E
C
54
3
1
5
43
1
1 3
45
4
7
4
1
5
1
4
1
58
1
1
1
1
11
11
1
1
1
1
5
13
1
10
4
9
9
4
1
13
1
9
25
17
43 56
2942
28 15
1
14
43 56
42
28
1
14
43 56
29
42
28
15
1
14
56
29
42
28 15
1
14
CA
C
A
A
C
A
C
C
A
C
A
A
C
A
C
A
C
C
A
C
A
A
C
A
C
A C
C
A
C
A
AC
A
C
C
ACA
C A
5
4
1
3
1
51
5
1
51
5
1 3
45
1 3
45
1 3
45
1
3
45
13
4
5
1
3
4
5
13
45
1
4
5
5 4
3
1
5
4
1
5
4
3
1
54
1
5
4 3
1
54
31
54
3
1
5 4
1
13
4 5
5
1
5
1
5
1
1
5
1
5
3
4
6
1
3 4
6
1
3
4
61
4
6
1
3
4
6
1
3
4
61
3
46
1
3
4
6
1
3
4
6
1
1
6
4
3
1
64
3
4
6
1
1
4
3
3
4
1
4
6
1
34
6
1
U1003 U1004
U8012
LED1
U8006
U1
X2
LI1
Q17
Q1
Q8
U14
TSU1
FB8000
U8004
Q1000
Q5
SOU1
D1007
D1006
D7
D4
AUD1
AUD3
D2
D6
Q14
Q13
Q8002
X1
X3X4
X5
U6
U41
U15
U8003
U40
U38
U12
UBD12
U7
UBD2UBD1
UBD3 UBD4
UBD6
UBD5
VR8000
U8001
U39
DPU1
U9
U11
U13
D8000
AUC19
AUC20
SC3
F2
F1
DPF2
D29
SC8003
SC8004
SC8000
SC8002
SC8001
SC2
SC8005
SC8006
SC1
R8042
R8026
R692
R8068
R336
LC8004
LC8010
LC8001
LC8002
LC3
LC4
LC5
D8011
D8005
D8004
D8003
D8002
D8001
C271
C24
C8081
C61
C8136
C8005
J10
Q8005
Q8004
Q8006
Q8003
U1002
U1001
U1000
U36
U31
DPU2
U32
U33
U25
U20
U23
U26
U27
U21
U24
U22
U29
TSQ1
Q8009
Q8010
Q8007
Q8008
DPQ7
Q11
DPQ6
M2Q1
DPQ5
Q12
Q10
Q4
Q3
Q16
DPQ1
Q6
Q15
Q8019
Q8017
Q8011
MADE IN TAIWAN REV.2
ADN553
SYS_FAN
1
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
Pin Assignment
1GND
2GND
3DC_IN
4DC_IN
XPin Assignment
1
Pin Assignment
1TACH
2VOUT
3GND
1
2
3
4
13
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
SATA Power (J1001) LVDS Inverter Power (J1002)
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
1
Pin Assignment
15V
25V
312V
4GND
5GND
Pin Assignment
1GND
2
3PWM Brightness Control
4Panel Power
5+3.3V
6Backlight On/Off
7Inverter Power
8
1
14
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
Front Panel (J11) COM1 (TSJ1)
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
Pin Assignment Pin Assignment
1Power Button 2SUS LED Power
3GND 4SUS LED
5Reset 6HDD LED
12
56
12
910
Pin RS232 RS422 RS485
1DCD- TXD- Data-
2SIN TXD+ Data+
3SOUT RXD+ NC
4DTR- RXD- NC
5GND GND GND
6DSR- NC NC
7RTS- NC NC
8CTS- NC NC
9RI- NC NC
15
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
DIO (J1000) Front Audio (AUJ1)
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
Pin Assignment Pin Assignment
1DIO7 2DIO6
3DIO5 4DIO4
5DIO3 6DIO2
7DIO1 8DIO0
95VSB 10 GND
12
910
12
910
Pin Assignment Pin Assignment
1Mic-L 2GND
3Mic-R 4NC
5Line-Out-R 6Mic-JD
7GND 8NC
9Line-Out-L 10 Line-JD
16
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
USB2.0 (J3) eSPI & UART Debug (J5)
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
Pin Assignment Pin Assignment
1VCC 2VCC
3-DATA 4-DATA
5+DATA 6+DATA
7GND 8GND
9NC 10 NC
1
210
9
Pin Assignment Pin Assignment
13V3SB 2ESPI_CLK
3ESPI_RST# 4GND
5ESPI_ALT# 6UART_TX
7ESPI_D0 8--
9ESPI_D1 10 ESPI_CS
11 ESPI_D2 12 UART_RX
13 ESPI_D3 14 3V3SB
14
12
17
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
LVDS (DPCN1)
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
Pin Assignment Pin Assignment
1GND 2GND
3LVDSA_Out3+ 4LVDSB_Out3+
5LVDSA_Out3- 6LVDSB_Out3-
7GND 8GND
9LVDSA_Out2+ 10 LVDSB_Out2+
11 LVDSA_Out2- 12 LVDSB_Out2-
13 GND 14 GND
15 LVDSA_Out1+ 16 LVDSB_Out1+
17 LVDSA_Out1- 18 LVDSB_Out1-
19 GND 20 GND
21 LVDSA_Out0+ 22 LVDSB_Out0+
23 LVDSA_Out0- 24 LVDSB_Out0-
25 GND 26 GND
27 LVDSA_CLK1+ 28 LVDSB_CLK1+
29 LVDSA_CLK1- 30 LVDSB_CLK1-
31 GND 32 GND
33 LVDS_DDC_CLK 34 NC
35 LVDS_DDC_DATA 36 +3.3V
37 Panel Power 38 Panel Power
39 Panel Power 40 Panel Power
12
40
39
18
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
eDP (DPCN2)
MH5
MH1
MH2
MH4
MH3
J1000
J1001
SW1000
J1002
F3
M2CN3-G4
M2CN3-G3
M2CN2-G5
M2CN2-G3
M2CN1-G3
J11
DPJP3
JP3
J5
D25
BZ1
Q9
U8005
U34
J3
TSJ1
AUJ1
AUU1
DIMM1
M2U1
UBU1
D1005
D1002
D1004
D1003
AUD2
D23
D8
D27
DPJP2
DPJP1
JP8000
DPQ3
Q8015
Q8001
Q8000
U16
UBD11
U8002
U8
U10
U8011
U8009
U8008
U8007
C8009
C8008
C8007
C8006
SC4
UBC3
M2LED3
M2LED2
M2LED1
LED2
DPF3
DPF1
UBEC1
UBR24
UBR12
R340
R341
LC8009
LC8008
LC8007
LC8006
LC8003
LC8000
EC8000
CN9
CN11
CN10
J1
DPQ8
Q8013
U4
U5
U3
U2
U28
U18
U17
U30
U19
DPQ4
DPQ2
Q8014
Q8016
Q7
Q18
Q8012
J4
M2CN4
U35
CN6
CN2
CN4
CN3
CN7
CN1
U8000
CN5
DPCN2
DPCN1
M2CN1
M2CN2
M2CN3
eSPI
USB-C_1
USB2_1/2
USB2_3
USB3_3
Front Audio
HDMI
USB3_1/2
Front Panel
COM1
DIO
SIM
DDI_B
DDR5
M.2_M
M.2_B
M.2_E
DC_IN
LAN3
LAN2
LAN1
HDA
LVDS
USB2_4/5
SATA0
SPI
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
Pin Assignment Pin Assignment
1NC 21 EDP_VCC_PANEL
2INV_PWR 22 EDP_VCC_PANEL
3INV_PWR 23 EDP_VCC_PANEL
4INV_PWR 24 GND
5INV_PWR 25 eDPB_AUXN
6NC 26 eDPB_AUXP
7NC 27 GND
8DIMMING_1 28 eDPB_LANE0_C_P
9BLONOFF_1 29 eDPB_LANE0_C_N
10 eDP_GND 30 GND
11 eDP_GND 31 eDPB_LANE1_C_P
12 eDP_GND 32 eDPB_LANE1_C_N
13 eDP_GND 33 GND
14 eDP_HPD_CON_1 34 eDPB_LANE2_C_P
15 GND 35 eDPB_LANE2_C_N
16 GND 36 GND
17 GND 37 eDPB_LANE3_C_P
18 GND 38 eDPB_LANE3_C_N
19 NC 39 GND
20 EDP_VCC_PANEL 40 NC
1
40
19
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
XExpansion Slots
Installing the M.2 Module
Before installing the M.2 module into the M.2 socket, please make sure that the following
safety cautions are well-attended.
1. Make sure the PC and all other peripheral devices connected to it has been powered
down.
2. Disconnect all power cords and cables.
3. Locate the M.2 socket on the system board
4. Make sure the notch on card is aligned to the key on the socket.
5. Make sure the standoff screw is removed from the standoff.
M.2 Module M.2 Socket
Key
Stand-off
Notch
DDR5 (DIMM1) 11
1
2
3
4
1
1
1
1
2
2
2
56
9
9
10
10
14
12
12
910
M.2 M Key
M.2 B-Key
1
1
1
1
12
40
40
39
1
1
2
210
9
65
M.2 E Key
1
3
2
1
2
3
M.2 B-Key
M.2 E-Key
M.2 M-Key
20
Chapter 2
HARDWARE INSTALLATION
User's Manual | ADN553
Please follow the steps below to install the card into the socket.
Step 2:
Press the end of the card far from the socket down until
against the stand-off.
Step 3:
Screw tight the card onto the stand-off with a screw driver
and a stand-off screw until the gap between the card and the
stand-off closes up. The card should be lying parallel to the
board when it’s correctly mounted.
Step 1:
Insert the card into the socket at an angle while making sure
the notch and key are perfectly aligned.
M.2 Module M.2 Socket
Key
Stand-off
Notch
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39

DFI ADN553 User manual

DFI
Brand
DFI
Model
ADN553
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents