Endres+Hauser Commuwin II Ethernet Connectivity Operating instructions

Brand: Endres+Hauser

Model: Commuwin II Ethernet Connectivity

Type: Operating instructions

Commuwin II

Ethernet Connectivity

Quick Installation Guide

BA 015S/04/en/06.01

Version 1.0

Table of Contents

1 Your package 3

2 Requirements 4

2.1 Hardware 4

2.2 Software 4

3 Installation of the Package 5

3.1 PROFIbus - Ethernet gateway 5

3.2 Commuwin II 5

3.3 PROFIbus device driver 5

3.4 Commuwin II Ethernet configuration software 7

3.5 Further configuration process 7

3.6 Deinstallation 7

4 Appendices 8

4.1 Configuring Commuwin II parameters 8

4.2 Some differences between operating systems WIN NT and WIN2000 8

Commuwin II Ethernet Connectivity Table of Contents

Endress+Hauser

IMPORTANT:

This document is intended as a quick installation guide.

For further information please refer to the documents supplied with this package.

VERY IMPORTANT:

For installation you must log on with administration rights.

Table of Contents Commuwin II Ethernet Connectivity

Endress+Hauser

1Your package

What you get:

•Optional Commuwin II software, including operating instructions

•Commuwin II Ethernet configuration software, Version V1.0 including manual

•two or more PROFIbus/Ethernet gateways, including installation manual

Note!

•If this package is to be used with an existing Commuwin II installation, please check that this

is Version V2.07-3 or higher. The software will not run with earlier versions.

Commuwin II Ethernet Connectivity Your package

Endress+Hauser

2Requirements

The CommuwinII Ethernet connectivity package was developed for the Windows operating

systems WIN NT and WIN 2000. It operates on any Intel hardware platform that is mentioned in

the WIN NT and WIN 2000 “Hardware compatibility list”.

Note!

•In all cases the hardware used must be supported by the WIN NT and WIN 2000 Hardware

compatibility list that can be found in the following Internet site:

http://www.microsoft.com

2.1 Hardware

Check that your computer fulfils the following requirements:

•Pentium III 200 MHz

•128 Mb RAM

•Ethernet TCP/IP interface card

•Connectivity for additional Ethernet participants within your local area network (connectors

and spare Ethernet IP addresses)

Note!

•If there is a PROFIboard or PROFIcard installed, please remove it.

2.2 Software

The CommuwinII Ethernet connectivity package requires the following installations for WIN NT:

• WIN NT 4.0 workstation or server

• Servicepack 4 or higher

The CommuwinII Ethernet connectivity package requires the following installations for WIN 2000:

• WIN 2000 professional or server edition

• Servicepack 1 or higher

Requirements Commuwin II Ethernet Connectivity

Endress+Hauser

3Installation of the Package

The prerequisites to the installation and configuration process are:

•you have installed and configured network access to your local area Ethernet TCP/IP network

(please contact your administrator),

•you have logged in to your operating system with administration rights,

•you have asked your network administrator for a list of free Ethernet addresses.

Furthermore, with respect to ease of installation, it is recommended that the installation sequence

presented here is strictly followed.

3.1 PROFIBUS - Ethernet gateway

Start with the installation and connection of one PROFIBUS - Ethernet gateway. Stay with the

default address of this gateway (refer to the installation manual). The installation and configuration

process for all the gateways required is described in detail in section 3.5.

Note!

•There may be a collision with another device already connected to your Ethernet. In this

case you must temporarily remove or reconfigure the device that has the same IP address as

the PROFIbus/Ethernet gateway. After you have configured all PROFIBUS/Ethernet gateways

to their dedicated IP addresses (refer to 3.5) you can reinstall or reconfigure the offending

device with its previous IP address.

3.2 Commuwin II

Commuwin II Version 2.07-3 or higher must be installed on your computer. If you already have a

version running:

•Check that it is version V2.07-3 or higher

•If this is not the case, purchase an update for your Commuwin II and install it.

3.2.1 Installation of Commuwin II

Insert the Commuwin II CD in your CD-ROM drive and follow the instructions in the installation

manual.

3.3 PROFIbus device driver

There are three different cases you may find at your site. Start with one of cases 3.3.1 to 3.3.3 and

then continue with 3.3.4.

3.3.1 Commuwin II, version V2.07-2 or lower, is already installed

When your package does not include full or update version of Commuwin II, please purchase a

Commuwin II update to V2.07-3, perform step 3.2.1 and then install the PROFIbus device driver

from the CommuWin II CD-ROM according to your operating system (WIN NT or WIN2000). Let

the setup reboot your computer and proceed with step 3.3.4.

Note!

•The PROFIBUS device drivers are to be found under \Drivers on the Commuwin II CD ROM.

Commuwin II Ethernet Connectivity Installation of the Package

Endress+Hauser

3.3.2 Commuwin II, version V2.07-3, is already installed

In this case there is no need to install Commuwin II or PROFIbus device driver. You only have to

reconfigure the PROFIbus device driver. Please invoke the “PROFIbus Control Panel” from the

folder “Settings” and proceed with step 3.3.4.

3.3.3 Commuwin II is not installed at all

Check that your package includes full version of Commuwin II, if not, purchase one:

•Install Commuwin II as described in step 3.2.1.

•Install the PROFIbus device driver from the Commuwin II CD-ROM according to your

operating system (WIN NT or WIN2000).

•Let the setup reboot your computer and proceed with step 3.3.4.

Note!

•The PROFIBUS device drivers are to be found under \Drivers on the Commuwin II CD ROM.

3.3.4 Configuring the PROFIbus device driver

If you came from step 3.3.1 or step 3.3.3:

•The “PROFIbus Control Panel” is automatically invoked after the restart of your computer.

•Select “PROFIgate” in the left hand window and press the button “Add”.

•Follow the wizard, acknowledge for “node0" and enter the default IP address of the Ethernet/

PROFIbus gateway (refer to the installation manual of the Ethernet - PROFIbus gateway).

•Press the button ”Apply". The result should be a green check mark for “node0" under

”PROFIgate".

•Press the button OK

If you came from step 3.3.2:

•Invoke the “PROFIbus Control Panel” manually.

•Please remove any node under “PROFIboard” or “PROFIcard” in the left hand window by

selecting the node and pressing the button “Remove”.

•Now select “PROFIgate” in the left hand window and press the button “Add”.

•Follow the wizard, acknowledge for “node0" and enter the default IP address of the Ethernet/

PROFIbus gateway (refer to the installation manual of the Ethernet - PROFIbus gateway).

•Press the button ”Apply". The result should be a green check mark for “node0" under

”PROFIgate".

•Press the button OK.

Installation of the Package Commuwin II Ethernet Connectivity

Endress+Hauser

3.4 Commuwin II Ethernet configuration software

If you have the AUTORUN-option for CD-ROM enabled, the installation of the CommuWin II

Ethernet configuration software will start automatically when inserting the CD-ROM. Otherwise run

setup or install on the CD-ROM.

•Insert the "Ethernet Connectivity for Commuwin II" CD in your CD-ROM drive.

•Follow the setup wizard.

•Allow the setup to reboot your computer.

•The additional reboot is necessary because this program uses a system service which is

automatically started during a system start.

3.5 Further configuration process

Start the program “Commuwin II Ethernet configurator” from the START-menu. Use the tab

“Configuration” to configure your IP addresses, the logical names and the PROFIbus - Ethernet

gateways. Refer to the context sensitive help for this tab by pressing the button “Help”. If you need

help beginning at top level you may press the button with the question mark or choose the help

option from the SART-menu.

The first Ethernet/PROFIbus gateway has already been installed with step 3.1. It’s current IP

address is the factory default. Enter the desired IP address from the list you got from your network

administrator, enter the logical name and then press the link “Gateway configuration”; you are

lead directly to the configuration site of the gateway where you can now enter the IP address you

just entered in the tab. Terminate the gateway’s configuration site.

Note!

•Before using the link make sure that your Internet explorer doesn’t use a proxyserver.

•For proper configuration of the gateway please use the password “MakeIt” and choose the

option “after next reboot”.

•If you are not able to reach the gateway configuration site, please refer to the gateway

manual and contact your network administrator.

Important!

•Connect the next gateways, one after the other to the Ethernet, and proceed as described

above for the first gateway; always use the tab “Configuration”.

3.6 Deinstallation

Please deinstall in the following order by using START–>Settings–>Control panel–>Software:

1. CommuWinII Ethernet configuration software

2. PROFIbus device driver

3. CommuWinII

Commuwin II Ethernet Connectivity Installation of the Package

Endress+Hauser

4Appendices

4.1 Configuring CommuwinII parameters

Before you start CommuwinII check the communication parameters. For example the following

parameters are used by the Pepperl&Fuchs segment coupler:

4.2 Some differences between operating systems WIN NT and

WIN2000

4.2.1 Starting the CommuwinII Ethernet configuration software twice

A second launch of the program, which may happen accidently when the program is iconized to

the taskbar notification area, is prevented under both WIN NT and WIN 2000.

Under WIN NT it is just re-activated with it’s full window, while under WIN 2000 the program remains

iconized.

4.2.2 Language aspects

Under WIN NT, the program uses the language of the “Regional settings” properties

(START–>Settings–>Control panel).

Under WIN 2000 the program uses the language of the localization properties of the operating

system. Regional settings are not supported

Appendices Commuwin II Ethernet Connectivity

Endress+Hauser

Austria

Endress+Hauser Ges.m.b.H.

Wien

Tel. (01) 88056-0,

Fax (01) 88056-35

Belgium / Luxembourg

Endress+Hauser S.A./N.V.

Brussels

Tel. (02) 2480600,

Fax (02) 2480553

Canada

Endress+Hauser Ltd.

Burlington, Ontario

Tel. (905) 6819292,

Fax (905) 6819444

Denmark

Endress+Hauser A/S

Søborg

Tel. (31) 673122,

Fax (31) 673045

Finland

Endress+Hauser Oy

Helsinki

Tel. (90) 204 83 160,

Fax (90) 204 83 161

France

Endress+Hauser

Huningue

Tel. 89696768,

Fax 89694802

Germany

Endress+Hauser Messtechnik

GmbH+Co.

Weil am Rhein

Tel. (07621) 975-01,

Fax (07621) 975-555

Great Britain

Endress+Hauser Ltd.

Manchester

Tel. (0161) 2865000,

Fax (0161) 9981841

Hong Kong

Endress+Hauser (H.K.) Ltd.

Hong Kong

Tel. 25283120,

Fax 28654171

Italy

Endress+Hauser Italia S.p.A.

Cernusco s/N Milano

Tel. (02) 92106421,

Fax (02) 92107153

Japan

Sakura Endress Co., Ltd.

Tokyo

Tel. (0422) 540611,

Fax (0422) 550275

Malaysia

Endress+Hauser (M) Sdn. Bhd.

Petaling Jaya,

Selangor Darul Ehsan

Tel. (03) 7334848,

Fax (03) 7338800

Netherland

Endress+Hauser B.V.

Naarden

Tel. (035) 6958611,

Fax (035) 6958825

Norway

Endress+Hauser A/S

Tranby

Tel. (032) 851085,

Fax (032) 851112

Singapore

Endress+Hauser (S.E.A.) Pte., Ltd.

Singapore

Tel. 4688222,

Fax 4666848

South Africa

Endress+Hauser Pty. Ltd.

Sandton

Tel. (011) 4441386,

Fax (011) 4441977

Spain

Endress+Hauser S.A.

Barcelona

Tel. (93) 4803366,

Fax (93) 4733839

Sweden

Endress+Hauser AB

Sollentuna

Tel. (08) 6261600,

Fax (08) 6269477

Switzerland

Endress+Hauser Metso AG

Reinach/BL 1

Tel. (061) 7156222,

Fax (061) 7111650

Thailand

Endress+Hauser Ltd.

Bangkok

Tel. (2) 9967811-20,

Fax (2) 9967810

USA

Endress+Hauser Inc.

Greenwood, Indiana

Tel. (317) 535-7138,

Fax (317) 535-1489

All other countries

Endress+Hauser GmbH+Co.

Instruments International

Weil am Rhein

Tel. (07621) 975-02,

Fax (07621) 975345

http://www.endress.com

12.97/MTM

BA 015S/04/en/06.01

CCS/CV5

Endres+Hauser Commuwin II Ethernet Connectivity Operating instructions

Endres+Hauser Commuwin II Ethernet Connectivity Operating instructions

Endres+Hauser Commuwin II Ethernet Connectivity Operating instructions

Related papers

Other documents