2. Architectural Mailboxes
  3. 3460B-10
3460B-10

Architectural Mailboxes 3460B-10 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Architectural Mailboxes 3460B-10 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Plastic Address Plaque (Model 3460)
Instructions
Thank you for purchasing this premium mailbox accessory item. We know you’ll be satisfied
with the years of service it will provide. If you have any questions about how to mount or use
this plaque, or if you need any replacement parts, please call us directly at (800) 464-7491 or
contact us at [email protected].
© 2017, Architectural Mailboxes, LLC Rev. C
www.architecturalmailboxes.com (800) 464-7491
Tools (not included)
Screwdriver
Power
screwdriver
Contents
1
Types of Applications
Applying Adhesive Numbers
2
wood/
sheet metal
screws (x2)
phillips
screws (x2)
Wrench
Drill bit
small
hex bolts (x2)
hex nuts (x2)
rubber
washers (x2)
plastic
adapters (x10)
cap nuts (x2)
Alcohol
Wipe
alcohol swab
packet (x1)
reflective
tape (x2)
Wood or Metal
Post
Mailbox
Gate
Storefront
Doorway
1
Peel reflective
tape from
backing.
Apply reflective
tape to address
plaque.
2
4
Apply numbers to
refective tape.
Note: If misaligned,
carefully peel
numbers and
reapply in correct
location.
adhesive
squares (x2)
adhesive
numbers x74
Note: 6 and 9
can be used
interchangeably.
1 2 2 6
2 5 6 7
1 0 0 9
Peel numbers
off the paper
backing.
3
5
6
5
Note: If misaligned,
carefully peel tape
and reapply in
correct location.
2
4
DIY Hint to Apply Numbers Stickers Straight and Evenly, Every Time!
R
Use a clear ruler and lightly stick the lower part of your number stickers onto the ruler’s edge using the ruler marks as your
guide to space the numbers evenly. Let the upper portion of the letters stick out the top. Set the ruler down and use your
finger to press the top of each sticker down in place on the reflective tape. When all the stickers are secure, carefully
remove the ruler and press the bottoms of the stickers in place with your finger.
Plastic Address Plaque (Model 3460)
Instructions
© 2017, Architectural Mailboxes, LLC Rev. C
www.architecturalmailboxes.com (800) 464-7491
Installation Instructions
3
FOR USE WITH ADHESIVE SQUARES
(no drilling required - best for clean smooth
surfaces like painted metal)
FOR USE WITH SCREWS
(more secure - drilling required)
Clean desired surface
with alcohol wipe.
Choose correct
adapters based on
surface curvature.
Place adapters into the
feet of the plaque and
secure with 2 small hex
bolts and 2 caps nuts.
Select proper hardware
based on the type of
application and secure
plaque to surface.
1
2
3
cap nuts x2
adapters x2
small hex bolts x2
adhesives
x2
Apply adhesive squares to
adapters and align plaque
at desired location. Secure
to surface by pressing
firmly on plaque feet.
4
Align plaque at desired
location and mark the
center of each hole.
X 2
Choose correct
adapter based on
surface curvature.
1
Clean desired surface
with alcohol wipe.
2
3
Align plaque at desired
location and mark the
center of each hole.
Drill pilot holes if necessary
(use 1/8” drill bit).
X 2
4
5
adapters x2
Place adapters into the
feet of the plaque.
5
!
!
There are 5 pairs, numbered
1 (flat) through 5 (most curved).
There are 5 pairs, numbered
1 (flat) through 5 (most curved).
Use the wood screws for 4x4
posts or fences.
Use the long Phillips screws,
washers and hex nuts for metal
and other thin surfaces.
R
The Adhesive Squares use advanced 3M® VHB™ adhesive that
chemically bonds to surfaces. For best results, make sure the
surface is clean, and press firmly onto the surface for 30 seconds
before releasing. Also note that maximum adhesion can take as
long as 72 hours, so after application let them set for best results.
*
/