2. Toro
  3. Two-Tank Setup Kit, FM 330 Fluid Mixer

Toro Two-Tank Setup Kit, FM 330 Fluid Mixer Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Two-Tank Setup Kit, FM 330 Fluid Mixer Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FormNo.3378-180RevA
Two-TankSetupKit
FM330FluidMixer
ModelNo.23895
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
Description
Qty.
Use
Endplate2
Trim1
Spacer
16
Bolt16
Nut16
Installtheendplates.
Topbracket2Installthetopbrackets.
InstallingtheEndPlates
1.Movethe2tankstoalevelsurface,andpositionthem
sothattheboltholesintheendplatesalignwiththe
boltholesinthebasesofthetanks.
Note:Thedistancebetweentheoutermostholesin
eachendplateis101.6cm(40inches).
2.Aligntheboltholesintheendplatewiththeboltholes
inthebaseofeachofthe2tanks,separatingtheend
platefromthebasewithaspacerateachbolthole
(Figure1andFigure2).
1 2
34
G024056
Figure1
500-gallontanks
1.Spacer(8)3.Bolt(8)
2.Nut(8)
4.Endplate
©2013—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3378-180*A
1 2
3
4
G023767
Figure2
1000-gallontanks
1.Spacer(8)3.Bolt(8)
2.Nut(8)
4.Endplate
Note:Dependingonwhetheryouhave500-gallon
tanksor1000-gallontanks,theendplatestonthe
tankframesdifferently;refertoFigure3.
1
2
G024057
Figure3
1.500-gallontanks2.1000-gallontanks
3.Insertaboltthrougheachhole,andsecureitwithanut.
4.Repeattheprocedurefortheotherendofthetank
bases.
5.Installthetrimontotheendplate(Figure4)wherethe
hosepassesthroughthebase.
1 2
G023768
Figure4
1.Endplate2.Trim
InstallingtheTopBrackets
1.Removetheinnermostnut(Figure5)oneachofthe
4supportrods.
Note:Retainthenutsforinstallingthebrackets.
1 2 2 1
G023769
Figure5
1.Nutstoloosen2.Nutstoremove
2.Loosenthenutsontheinsidefaceofeachofthe4
outsideverticalsupports.
3.Slidethesupportrodsoverjustfarenoughforthetop
bracketstotbetweentheinsideverticalsupports.
4.Aligntheboltholesinthetopbracketswiththebolt
holesintheverticalsupports(Figure6),andslidethe
rodsinwardthroughtheboltholes.
1 2
G023770
Figure6
1.Nut(4,existing)2.Topbracket(2)
5.Installtheexistinginnermostnuts.
6.Tightenallthenutstosecuretherodsandthebrackets.
2
/