ANZZI SD-AZ03BBH-L Installation guide

Type
Installation guide

This manual is also suitable for

ANZZI SD-AZ03BBH-L is a shower panel series that includes a fixed glass panel and a sliding door. The sliding door has two rollers at the top and two at the bottom, which allow it to move smoothly and quietly. The door is also equipped with a rubber seal to prevent water from leaking out. The fixed glass panel is supported by two glass support brackets and a top bracket to for added stability. The structural arm provides additional support to the top bracket and the wall. The door side seal helps to keep water from leaking out from the sides of the door.

ANZZI SD-AZ03BBH-L is a shower panel series that includes a fixed glass panel and a sliding door. The sliding door has two rollers at the top and two at the bottom, which allow it to move smoothly and quietly. The door is also equipped with a rubber seal to prevent water from leaking out. The fixed glass panel is supported by two glass support brackets and a top bracket to for added stability. The structural arm provides additional support to the top bracket and the wall. The door side seal helps to keep water from leaking out from the sides of the door.

1
2
3
5
6
4
7 8 9
11
10
13 12
13
12
11
10
9
8
7
6
5
4
3
2
1
1
1
Handle
Single Rollers
Structural rail
Wall mounted bracket
ST5*40
Door side seal strip
Fixed glass panel
Moving glass panel
Top bracket
Structural arm
Glass support
Wall anchor(8)
Rubber seal
1
2
4
2
1
1
1
5
2
5
3
NO.
Qty
Drawing
Description
Componentlist
NOTE: Unpack your unit carefully and inspect it. Identify all parts using the detailed diagram and packing list
in this manual as a reference. Before discarding the carton, check for small hardware bags that may have
fallen to the bottom of the box. If any parts are damaged or missing, please contact ANZZI at
1-844-44-ANZZI or [email protected].
SD-AZ03
SHOWER PANEL SERIES
Guard Rail
1. Lay the structural guard rail (8) along the ground. Insert the
two wall mounting brackets (7) at both ends of the structural
guard rail. Mark on the wall where to drill the hole to allow the
wall mounting bracket anchors to be installed.
2. Drill the holes with an 8mm drill bit and insert the white
plastic anchors. Before screwing the mounting brackets in place,
insert the rollers (9). Once the rollers are inserted into the guard
rail fix the wall mounting brackets to the wall.
Fixed Panel
3. Install the rubber seal (1) on to the side of the fixed glass
panel (5). Then, install the glass supporting brackets (3) to the
fixed glass panel.
4. Insert the glass panel to the guard rail. On the shower wall
mark where to drill to anchor the glass supporting brackets.
5. Move the glass panel away to make room to drill the 8mm
holes for the supporting brackets and insert a white plastic
anchor. Then screw the supporting bracket into the wall using
the provided screws (6).
Top Bracket
6. On the top side of the fixed panel install the top bracket (12).
7. Insert the sliding glass panel (11) into place and install the top
bracket on this panel as well. Make sure to line up both top
bracket pieces.
Sliding Door
8. Install the rollers to the sliding glass panel. Then install the
remaining two rubber seal strippers on both ends of the sliding
glass panel.
9. Close the sliding glass door and inspect to make sure there is
no gap between the sliding glass panel and the wall. Make any
adjustments as need to the top mounting bracket to achieve the
correct extension of the door.
Finishing
10. Position the structural arm (13) and install to the top
mounting brackets and the wall.
11. Fix the handle (10) to the sliding glass panel.
12. Install the door side seal (4) to the fixed glass panel’s edge.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ANZZI SD-AZ03BBH-L Installation guide

Type
Installation guide
This manual is also suitable for

ANZZI SD-AZ03BBH-L is a shower panel series that includes a fixed glass panel and a sliding door. The sliding door has two rollers at the top and two at the bottom, which allow it to move smoothly and quietly. The door is also equipped with a rubber seal to prevent water from leaking out. The fixed glass panel is supported by two glass support brackets and a top bracket to for added stability. The structural arm provides additional support to the top bracket and the wall. The door side seal helps to keep water from leaking out from the sides of the door.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI