Apollo NAPOLI TDNA-6066CG-BN Installation Instructions Manual

Type
Installation Instructions Manual
SHOWER TUB
SDNA-4876CG-CH & SDNA-4876CG-BN TDNA-6066CG-CH & TDNA-6066CG-BN
SDNA-6076CG-CH & SDNA-6076CG-BN
INSTALLATION INSTRUCTIONS
NAPOLI
CH - Chrome
BN - Brushed Nickel
1
This product is heavy and may require two people to install.
Inspect the product immediately upon receipt for transit damage, missing packs/parts or
manufacturing fault. Damage reported later will not be accepted. Handle the product with care
avoiding knocks and shock loading to all sides and edges of the glass.
Read these instructions carefully before start of installation.
Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: This product is heavy and may require two people to install.
After use, your shower should be cleaned with soap and water. This is particularly important in hard
water districts where insoluble lime salts maybe deposited and allowed to build up. Cleaners of a
gritty or abrasive nature should not be used. Care should be taken to avoid contact with strong
chemicals, they can be used but with caution, if in doubt contact the manufacturer of the cleaner in
question.
Keep these instructions for aftercare and customer service details.
Tape
Phillips
Silicone
Measure
Power
Drill
PencilLevel Screwdriver Hammer
Painter’s Tape
Drill
bit
(Ø=5/16")
(Ø=8mm)
Drill
bit
(Ø=1/8")
(Ø=3mm)
Metal File
Miter
saw or Hacksaw
D
A
C
!
IMPORTANT INFORMATION
REGARDING THE INSTALLATION
OF THIS SHOWER DOOR
F
DOOR
PANEL
B
E
A
B
Guide Rail Brackets must be firmly
attached to the wall. Installation into a
stud is strongly recommended.
All of the guide rail bracket set
screws must be tightened.
A
Roller Guards must be postioned and
secured within 1/16” of Upper Guide Rail
D
Bumper Vinyl Seal must be installed on
the closing edge of the door glass
E
PLEASE READ THE ENCLOSED INSTALLATION
MANUAL FOR DETAILS REGARDING PROPER
INSTALLATION.
The Guide Block must be screwed to the
threshold and installed square to the panel
glass and door glass. Installing the guide
block crooked may damage the bottom edge
of the door glass and lead to breakage.
F
Thread Lock must be applied to both
stopper set screws.
Panel-side stopper must be installed
into the pre-drilled stopper hole in
the upper guide rail.
Door-side stopper must be installed
at the proper position to stop the
door from contacting the wall.
B
Roller Wheel Safety Set Screws must
be re-tightened after installation
C
Right hand door installation shown as an example
2
3
Detailed Diagram of shower door components
1
11
12
13
14
15
16
17
18
19
2
3
4
5
6
7
8
9
10
21
20
4
Detailed Diagram of shower door components
Parts List
Threshold
# Item Qty # Item Qty
01
Running Rail 1pc
09
10
11
12
13
14
15
16
17
18
19
20
21
Gasket-B 1pc
02
Wall Brackets 2pcs
Gasket-C
2pcs
2pcs
03
Anti Jump Knobs 2pcs
Fixed Panel Bottom Gasket
04
Roller 2pcs
Bottom Glass Clip 1pc
1pc
1pc
1pc
05 Bump Stopper
2pcs
Bottom Guide 1pc
06
Glass Fixing Piece 2pcs
07
Handle
1pc
08
Gasket-A
2pcs
# Box
2
Fixed panel
Door panel & Profile & Parts
1
21
Boxes
Package Contents by part#
2pcs
5pcs
Φ1/4 (6mm) wall anchors
Allen Wrench:
2.5mm 3mm 4mm 5mm 6mm
x1 for each
Φ5/16 (8mm) wall anchors 2pcs
2pcs
2pcs
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
Countersunk Screw ST4x35
Truss Head Screw ST5x55
Door Panel
Fixed Panel
FINISHED WALL TO FINISHED WALL
TOP VIEW
CUT THE LENGTH OF THE THRESHOLD
1
FORMULA
THRESHOLD = FINISHED WALL TO FINISHED WALL
14
2
CALCULATE THE LENGTH OF THE RUNNING RAIL REQUIRED USING THE FORMULA PROVIDED
FINISHED WALL TO FINISHED WALL AT THE BAR LEVEL
TOP VIEW
FORMULA
RUNNING RAIL = SUBTRACT 1" (24mm) FROM THE
OPENING BETWEEN FNISHED WALLS
glass bracket
door end
holes
5
RUNNING RAIL
3
Step 3A
Step 3B
Position the bump stoppers (5) on the bar (1) as
illustrated. Secure them temporarily in place.
Position the wall brackets (2) on the running rail (1)
as illustrated. Secure them temporarily in place.
1
5
2 2
6
21
6
1
GLASS HOLDERS
4
GLASS CLIPS
5
Washer
Glass hole
6
1
21
21
13
12
FLUSH WITH
GLASS EDGE
1 1/2"
(40mm)
Insert bottom gaskets (11) in the bottom
glass clips (12)(13).
Position the bottom glass clip and bottom
guide on fixed panel as illustrated.
Step 4A
Step 5A
Fasten the running rail (1) to the fixed panel (21)
with the glass fixing piece (6).
Secure them temporarily in place.
Ensure that the running rail (1) is at the highest
possible position in reference to the holes of
the fixed panel (21).
INTERIOR
SHOWER SIDE
11
13
12
7
PLACE THE PANEL ON CARBOARD BOX
TO INSTALL THE BOTTOM GASKET
INTERIOR
SHOWER SIDE
17
INSTALL THE BOTTOM DOOR GASKET ON THE DOOR PANEL
6
9
20
20
8
B
Step 7A
Position the fixed panel assembly (21) on thresh
old of base (B) as shown.
Adjust the fixed panel (21), by way of the running
rail (1), so as to force the gasket (10) against
the wall.
Ensure that the running rail (1) is level and that
the fixed panel (21) is square. If a horizontal cor
rection is required, adjust and level the glass
fixing piece (6).
Step 7B
21
2
10
7
21
FIXED PANEL
7
The bottom guide (13) can hang off the threshold
(B) as long as it can be well fastened.
INTERIOR
SHOWER SIDE
13
B
20
21
10
20
7
1
6
90°
90°
21
9
Step 8A
Mark the screw locations for the wall brackets
(2) on the walls on both sides of shower as
well as the placement of the bottom glass clips
(12) (13).
Step 8B
Secure glass clips (12) (13) with self-tapping
screws.
2
13
12
FIXED PANEL
8
18
16
14
10
Step 9A
Mark the screw locations on the walls on both
sides of shower. Remove the running rail (1)
from the wall brackets (2). Drill holes in walls
until wall stud is reached with a drill bit
intended for ceramic tiles.
Fasten the wall brackets (2) with screws
ST5x2 1/8" (19).
Step 9B
Insert fixed panel (21) back, ensuring that it's
placed in the bottom glass clips (12) (13).
Slide expander over wall bracket (2) and
fasten set screws.
2
WALL BRACKERS
9
2
1
13
12
11
Step 10A
Assemble the 2 top rollers (2) to the door
panel (20) as illustrated.
Step 10B
WASHER
GLASS HOLE
Install anti jump knobs (3), making sure that
they are tangent to the running rail (1).
Through the use of the crammed washers,
adjust rollers so that the sliding door panel is
parallel to the running rail.
20
Interior shower side
4
4
1
SLIDING DOOR
10
3
12
Step 11A
Install door panel (20), ensure rollers are positioned on top of the running rail (1).
Install handle (7) onto sliding door (20). Ensure that clear washers on either side of glass are
installed.
Ensure that the door panel (20) is placed within the bottom center guide (13).
Note the placement of the bottom door gasket (9).
INTERIOR
SHOWER SIDE
SLIDING DOOR
11
7
20
9
13
Step 12A
Install door side gasket (8) onto
sliding fixed panel (21).
8
20
21
8
GASKETS INSTALLATION
12
TOP
20
8
21
BOTTOM
3/4"
(17.5mm)
14
13
Step 13A
Adjust the position of the stoppers (5)
so as to ensure a maximum opening
and closing range. Ensure that the
sliding door gasket (10) is forced
against the wall.
5
5
4
1
Door closed
20
7
21
Door open
10
20
STOPPERS
13
15
Step 14A
Apply silicone between the bottom of the
fixed panel and the threshold of the base.
Silicone application along the length of
the threshold is also suggested. In both
cases, it is done from the outside of the
shower area.
SILICONE
14
16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Apollo NAPOLI TDNA-6066CG-BN Installation Instructions Manual

Type
Installation Instructions Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI