olympia electronics BOX-53X User manual

BOX-53X
Brand
olympia electronics
Model
BOX-53X
Type
User manual

Olympia Electronics BOX-53X is a sealing box designed to protect call buttons from moisture, dust, and water, ensuring reliable operation in demanding environments. Suitable for various call buttons produced by Olympia Electronics, it offers an IP65 protection rating, safeguarding against dust ingress and low-pressure water jets from any direction. The box features pre-marked entrances for easy cable routing and includes mounting accessories for secure installation.

Olympia Electronics BOX-53X is a sealing box designed to protect call buttons from moisture, dust, and water, ensuring reliable operation in demanding environments. Suitable for various call buttons produced by Olympia Electronics, it offers an IP65 protection rating, safeguarding against dust ingress and low-pressure water jets from any direction. The box features pre-marked entrances for easy cable routing and includes mounting accessories for secure installation.

927530000_09_001 927530000_09_001 927530000_09_001
231
5
3
4
7
8
Screw
Washer 6
1
1
1
2
General
BOX-53X
Mounting Accessories
Manual
Adhesive films
The BOX-53X series are sealing boxes, which are used to protect call buttons (fire
detection, extinguishing, etc.) from moisture, dust and water. The sealing boxes
are compatible with all call buttons produced by Olympia Electronics.
Installation Instructions
Package Contents
WALL PLUG
Rubber
Sealing Ring
Place the box on the wall and fasten it with the supplied mounting accessories.
WARNING!!! The lid should be fitted.
Open one of the pre-marked entrances to pass the connecting cables along with
the supplied cable gland. The cables must not be deformed (this WARNING!!
requirement is important to preserve the degree of IP65 protection).
Remove the button front restraint screws.
Open one of the pre-marked entrances at the base of the button, pass the
connection cables and screw the base into the box. To connect the cables, refer
to the button instruction manual.
Replace the button front and fasten the removed screws . The device is ready to
be activated.
1
2
3
Drill the four available holes with a 4mm drill to mount the box on the wall.
4mm
12
34
Install the appropriate adhesive film according to the type of the button are
going to use. The film must be placed inside from the plastic. Mind the correct
orientantion!
The lid is easily removed for safety reasons. Replace it in case it is removed
from the base.
927530000_09_001
IP65
BOX-530
WATERPROOF CASE FOR
FIRE DETECTION/EXTINGUISHING
MANUAL CALL POINT
5
4
European
manufacturers
Thank you for your trust in our products
Olympia Electronics - European manufacturer
Warranty
Olympia Electronics reserves the right to repair or to replace the
returned goods and to or not charge the buyer depending on the
reason of defection. Olympia Electronics reserves the right to charge
or not the buyer the transportation cost.
Olympia Electronics guarantees the quality, condition and operation
of the goods. The period of warranty is specified in the official
catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the
buyer does not follow the technical instructions included in official
documents given by Olympia Electronics or if the buyer modifies the
goods provided or has any repairs or re-setting done by a third party,
unless Olympia Electronics has fully agreed to them in writing.
Products that have been damaged can be returned to the premises of
our company for repair or replacement, as long as the warranty
period is valid.
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.com
info@olympia-electronics.gr
Dimensions
180mm
340mm
76mm
114mm
927530000_09_001
4
11
Close the lid and press firmly on the plastic latch until you hear the “click”.
9
10
CLICK
  • Page 1 1
  • Page 2 2

olympia electronics BOX-53X User manual

BOX-53X
Brand
olympia electronics
Model
BOX-53X
Type
User manual

Olympia Electronics BOX-53X is a sealing box designed to protect call buttons from moisture, dust, and water, ensuring reliable operation in demanding environments. Suitable for various call buttons produced by Olympia Electronics, it offers an IP65 protection rating, safeguarding against dust ingress and low-pressure water jets from any direction. The box features pre-marked entrances for easy cable routing and includes mounting accessories for secure installation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents