Paradyne Hotwire 6351 Installation Instructions Manual

Brand: Paradyne

Model: Hotwire 6351

Category: Routers

Type: Installation Instructions Manual

This manual is also suitable for

Hotwire ReachDSL 6351

Paradyne Hotwire 6351 is an IP router that connects a DSL link to an Ethernet network, providing high-speed Internet or corporate LAN access over traditional twisted-pair copper telephone wiring. It operates with Hotwire 8312 and 8314 ReachDSL cards in the DSLAM system, dynamically adapting and allocating bandwidth to optimize applications. The ReachDSL Router supports line sharing by data and voice services without requiring a POTS splitter at the demarcation point, and uses standard phone wiring for connection.

Hotwire

6351 ReachDSL

™

Router

Installation Instructions

Document Number 6351-A2-GN10-20

February 2004

Contents

Software and Firmware License Agreement ................................................. 1

Product Documentation Online ..................................................................... 3

Hotwire 6351 ReachDSL Router Overview .................................................. 3

Getting Started .............................................................................................. 6

Installing the Hotwire 6351 ReachDSL Router ............................................. 7

Power-On ...................................................................................................... 12

Troubleshooting ............................................................................................ 13

Configuration Setup ...................................................................................... 14

Graphical User Interface ............................................................................... 15

Cables and Connectors ................................................................................ 17

Optional Wall Placement ............................................................................... 20

ReachDSL Router Technical Specifications ................................................. 22

Important Safety Instructions ........................................................................ 23

Government Requirements ........................................................................... 24

Warranty, Sales, Service, and Training Information ...................................... 28

Software and Firmware License Agreement

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

The terms and conditions of this License Agreement (the “Agreement”) will apply to the

software and/or firmware (individually or collectively the “Software”) incorporated into

the Paradyne product (the “Product”) purchased by you and any derivatives obtained

from the Software, including any copy of either. If you have executed a separate written

agreement covering the Software supplied to you under this purchase, such separate

written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept

a personal, non-transferable, non-exclusive, right (without the right to sublicense) to use

the Software, solely as it is intended and solely as incorporated in the Product

purchased from Paradyne or its authorized distributor or reseller under the following

terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The

Licensee acquires no title, right or interest in the Software other than the license

granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in which

the Product was rightfully purchased except upon prior written notice to Paradyne

and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the Software in

whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

5. Except for the Product warranty contained in the manual, the Software is provided

“AS IS” and in its present state and condition and Paradyne makes no other

warranty whatsoever with respect to the Product purchased by you. THIS

AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES, WHETHER

EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING WITHOUT

LIMITATION:

a. Any warranty that the Software is error-free, will operate uninterrupted in your

operating environment, or is compatible with any equipment or software

configurations; and

b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied warranties

on limitations on how long an implied warranty lasts, so the above limitations may

not apply to you. This warranty gives you specific legal rights, and you may also

have other rights which vary from one state or jurisdiction to another.

6. IN NO EVENT WILL PARADYNE BE LIABLE TO LICENSEE FOR ANY

CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR SPECIAL DAMAGES,

INCLUDING ANY LOST PROFITS OR LOST SAVINGS, LOSS OF BUSINESS

INFORMATION OR BUSINESS INTERRUPTION OR OTHER PECUNIARY LOSS

ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE,

WHETHER BASED ON CONTRACT, TORT, WARRANTY OR OTHER LEGAL OR

EQUITABLE GROUNDS, EVEN IF PARADYNE HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY THIRD

PARTY.

7. The rights granted under this Agreement may not be assigned, sublicensed or

otherwise transferred by the Licensee to any third party without the prior written

consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be terminated

in the event of breach by the Licensee of any provisions of this Agreement.

9. Upon such termination, the Licensee shall refrain from any further use of the

Software and destroy the original and all copies of the Software in the possession of

Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without

regard to its provisions concerning conflicts of laws.

Product Documentation Online

Complete documentation for this product is available at www.paradyne.com.

Select Library → Technical Manuals → Hotwire DSL Systems.

To order a paper copy of a Paradyne document, or to speak with a sales representative,

please call 1-727-530-2000.

Hotwire 6351 ReachDSL Router Overview

The Hotwire

6351 ReachDSL

™

Router is a component in the Hotwire ReachDSL

System that interoperates with Hotwire 8312 and 8314 ReachDSL cards in the Digital

Subscriber Line Access Multiplexer (DSLAM) system.

The ReachDSL Router operates as an IP router, connecting a DSL link to an Ethernet

network to provide high-speed Internet or corporate LAN access over traditional

twisted-pair copper telephone wiring. ReachDSL technology operates over existing

copper wire with existing telephone jacks to provide adaptive rates, and to dynamically

adapt and allocate bandwidth to optimize applications.

Hotwire ReachDSL System

Copper pairs run from the central office (CO) to the customer premises (CP) to create

the local loop. The local loop terminates on the customer premises at the demarcation

point.

For more information about Hotwire DSL Routers, refer to the following document:

6371-A2-GB20 Hotwire DSL Routers User’s Guide

To install a phone filter, refer to the appropriate document:

6035-A2-GN11 Hotwire 6035 Universal Phone Filter Installation Instructions

6040-A2-GN11 Hotwire 6040 Universal Wall Jack Phone Filter Installation

Instructions

The ReachDSL Router does not require a POTS splitter at the demarcation point to

support line sharing by data and voice services. Standard phone wiring is used for

connection to the router.

NOTE:

In this document:

— A telephone is used to represent any equipment that plugs into a phone jack

and uses the POTS line, such as a phone, modem, or fax machine.

— End-user system is used to represent any host with an Ethernet connection

and ReachDSL-based service.

— RJ11 wall jack is used to represent either an RJ11 or RJ14 wall jack. The RJ14

wall jack is used for a phone with two lines.

— Service provider is used to represent any Internet Service Provider (ISP) or

remote Local Area Network (LAN) provider.

01-16938-01

ReachDSL

Router

Customer Premises (CP)

DSL/POTS

Ethernet

Crossover

Cable

Ethernet

Cable

Central

Office

(CO)

Local Loop

Hub

DSL – Digital Subscriber Lines

POTS – Plain Old Telephone Service

End-user

Systems

Network

Service

Provider

(NSP)

Demarcation

Point

Filter

Phone Filters

For optimum performance, if the wiring for the router is also used for voice (POTS), a

phone filter should be installed on each voice line with a phone, modem, fax machine, or

other telecommunications device attached. One Hotwire phone filter can be used with

multiple telecommunications devices (for example, a phone and a fax machine can be

supported using a single filter), provided a multiple line adapter is used.

There are two Hotwire phone filters that can be used with the ReachDSL Router:

 Hotwire 6035 Universal Phone Filter is designed for use with a tabletop phone.

 Hotwire 6040 Universal Wall Jack Phone Filter is designed for use with a

wall phone.

01-17038

RJ11

Wall Jack

RJ11

Wall

Jack

Customer

Premises (CP)

DSL

Router

6035

Phone Filter

6040

Wall Jack

Phone

Filter

Phone Filter

Getting Started

Before beginning your router’s installation, make sure that you have all the equipment

that you will need.

Package Checklist

In addition to these instructions, verify that your package contains the following:

❑ Hotwire 6351 ReachDSL Router

❑ DSL interface cable with RJ11 modular plugs

❑ Power cord with power transformer

Wiring and Connectors You Will Need

The following wiring and standard connectors are used with this product:

❑ Standard RJ11 (or RJ14) wall jack for the DSL cable.

❑ Multiple line adapter if a telephone and router are connected in the same location.

❑ Standard Ethernet 8-pin, non-keyed modular plug for a PC or workstation with an

Ethernet straight-through or crossover cable.

— Refer to procedures in Installing the Hotwire 6351 ReachDSL Router on

page 7 to install cables.

— Refer to Cables and Connectors on page 17 for standard pin numbers.

Optional Cable and Adapters

The Hotwire 6351 ReachDSL Router is typically configured remotely by the service

provider. The following optional cable and adapters are only used when configuring the

router locally:

❑ Console cable: Straight-through cable with 8-pin non-keyed modular plugs

(Part No. 035-0276-1431)

❑ Console adapter:

— 8-pin modular-to-DB9 adapter plug (Part No. 002-0093-0031), or

— A configurable DB9-to-RJ45 adapter, wired as shown in 8-Pin Modular to DB9

Adapter Plug on page 18.

Installing the Hotwire 6351 ReachDSL Router

Place the ReachDSL router on a flat surface, with clearance for the rear connectors. For

router cable pin assignments, refer to Cables and Connectors on page 17.

Connecting the DSL Line in a Home Environment (Phone and Router in

the Same Location)

Use the supplied RJ11 6-pin cable for the DSL connection. You will also need a multiple

line adapter and a phone filter (see Phone Filters on page 5).

Procedure

1. Insert a multiple line adapter into the wall jack.

2. Insert one end of the cable into the DSL jack on the router.

3. Insert the other end of the cable into one of the jacks (Line 1 or Line 2) on the

multiple line adapter.

4. Insert the line cord from the LINE jack on the filter into the empty jack on the

multiple line adapter.

5. Insert the phone line cord from the phone into the PHONE jack on the filter.

POW

CONSOLE

DSL

ETHERNET

01-17017

LINE

PHO

6351 ReachDSL Router

Multiple

Line

Adapter

Filter

Connecting the DSL Line in All Other Environments

Use the supplied RJ11 6-pin cable for the DSL connection.

Procedure

1. Insert one end of the cable into the DSL jack on the router.

2. Insert the other end of the cable into the wall jack.

POW

CONSOLE

DSL

ETHERNET

01-16927

Wall

Jack

6351 ReachDSL Router

Connecting the Ethernet Cable

Use an 8-pin Ethernet straight-through or crossover cable for the Ethernet connection.

Procedure

To connect an Ethernet Hub using a straight-through cable:

— Insert one end of the straight-through cable into the ETHERNET jack on the

router and connect the other end to an Ethernet hub. Do not connect it to the

hub’s optional Uplink connection; the Uplink connection requires an Ethernet

crossover cable. To support multiple end-user systems, refer to Increasing the

Number of End-User Systems on page 14.

To connect a PC using a crossover cable:

— Insert one end of the crossover cable into the ETHERNET jack on the router

and connect the other end of the cable to a PC with an Ethernet Network

Interface Card (NIC) installed.

01-16928-01

Ethernet

Line

POWER

CONSOLE

DSL

ETHERNET

Ethernet

Hub

Ethernet

Straight-through

Cable

6351 ReachDSL Router

01-16929-01

PC with Ethernet

Network Interface

Card (NIC)

Ethernet

Line

Ethernet

Crossover

Cable

POWER

CONSOLE

DSL

ETHERNET

6351 ReachDSL Router

Connecting to a VT100 Terminal or PC (Optional)

The Console port acts as a DCE and uses an 8-pin straight-through cable for the

connection to a VT100 terminal or a PC running a terminal emulation program. It is an

optional connection that is only used for local configuration of the router.

To set up the VT100 terminal or PC for local configuration and to access the router, refer

to Configuration Setup and Accessing the Router on page 14.

Procedure

1. Connect a DB9 adapter to the PC.

2. Insert one end of the cable into the DB9 adapter for the serial port of the VT100

terminal or PC.

3. Insert the other end of the straight-through cable into the CONSOLE jack on the

router.

VT100 Terminal

or PC

(9-pin Adapter)

01-16930-01

Console

Serial Line

POWER

CONSOLE

DSL

ETHERNET

6351 ReachDSL Router

Connecting Power

Procedure

1. Insert the supplied power cord’s round end into the POWER jack on the router.

2. Plug the transformer into an AC outlet.

Installation of the hardware is now complete. When the power cord is installed, the

router goes through a power-on self-test.

POWER

CONSOLE

DSL

ETHERNET

01-16931-01

18 VDC

800 MA

Transformer

Power

Jack

6351 ReachDSL Router

Power-On

When power is applied, the router performs self-diagnostics and the PWR LED is on.

The self-diagnostics include a power-on self-test. During the power-on self-test, all of

the LEDs turn on for one second.

Status LEDs

After a successful self-test, the LEDs should appear as indicated in BOLD in the

Condition column below. Refer to Troubleshooting on page 13 for LED indications

requiring action.

LED Condition Status

PWR ON The router has power.

ALM Blinking

OFF

A firmware download is in progress. The TST LED is also

on during a download.

An alarm condition exists.

No alarms have been detected by the router.

TST ON

OFF

The TST LED is on during the power-on self-test, during a

test initiated by the service provider, and during a firmware

download.

No tests are active.

LINE ON

OFF

The DSL link is active and ready to transmit and receive

data.

No DSL link has been established.

TX/RX ON

OFF

Data transmission is in progress on the DSL line.

No data is being transmitted or received by the router.

ETHERNET ON

OFF

The Ethernet connection is active.

No Ethernet device is detected.

01-16932

Hotwire 6351

ReachDSL

Router

TST

LINE

ETHERNET

ALMPWR

Power – green

Alarm – red

Test – yellow

Transmit/Receive – green

Ethernet Link – green

TX/RX

DSL Line – green

ReachDSL

6351

Troubleshooting

LED Symptom Action

All LEDs are on. If the LEDs remain on for more than ten minutes, the router

is not functional. Contact the service provider.

ALM LED remains on. The power-on self-test may have failed. Unplug the router

and reapply power. If the alarm LED is still on, contact the

service provider.

ALM and TST LEDs

are blinking.

A firmware download may be in progress. If a firmware

download is not in progress, or if the LEDs continue blinking

for more than ten minutes, contact the service provider.

Ethernet LED is off. Verify that the Ethernet cable is securely installed at both

ends, and at least one PC is connected and powered on.

Verify that the correct cable is installed. Refer to Connecting

the Ethernet Cable on page 9.

LINE LED is off. Verify that the DSL LINE cable is securely installed on both

ends. If the problem continues, contact the service provider.

On lines with POTS, verify that the line has dial tone (loops

without POTS do not have dial tone). If there is no dial tone

on the POTS line, contact the service provider.

LINE LED is on but

there is no data

transmission.

The DSL link has been established but no data is being

transmitted. Verify the Ethernet connection. If the problem

persists, contact the service provider.

LINE and Ethernet

LEDs are on and there

is no data transmission.

Both the DSL and Ethernet links have been established, but

no data is being transmitted. If the problem continues,

contact the service provider.

PWR LED is off. Check that the power cord is securely installed on both

ends.

If no LEDs are on, the power supply may be defective. Test

the outlet to verify power.

If other LEDs are on, the PWR LED may be burned out.

Unplug the unit and reapply power; watch all LEDs during

the power-on self-test to verify that the PWR LED is

functioning. If the problem persists, contact the service

provider.

TST LED is on. A test initiated by the service provider may be active. Wait

ten minutes. If the TST LED does not go off, contact the

service provider.

Configuration Setup

If a CD-ROM is included with your ReachDSL router, proceed to Graphical User

Interface on page 15.

The Console connection can be used to locally configure the router with a

VT100-compatible terminal or PC running a terminal emulation program. Refer to

Connecting to a VT100 Terminal or PC (Optional) on page 10 for cabling.

Verify the terminal settings:

 Data rate is set to 19.2 Kbps (19200 bps).

 Character length is set to 8.

 Parity is set to None.

 Stop bits is set to 1.

 Flow control is set to Off or None.

Accessing the Router

When the local console connection is first established, access control to the ReachDSL

router displays an initial prompt of Login>.

Procedure

1. At the initial prompt of Login>, enter the factory default Login ID of paradyne.

2. At the password> prompt, enter the factory default Password of abc123.

3. At the next prompt for System ID, the factory default is CUSTOMER>.

Type show system to display hardware/firmware information and Selftest Results

(optional).

Refer to the Hotwire DSL Routers User’s Guide for configuration settings and command

line entries.

Increasing the Number of End-User Systems

A single PC is attached to the router by using an Ethernet crossover cable.

The router can support differing numbers of end-user systems, depending on the

functions that are enabled and traffic loading. Typical configurations provide support for

up to 32, 64, or 256 hosts (end-user systems).

To increase the number of PCs, connect all PCs to an Ethernet hub using a straight-

through cable. The number of end-user systems can be increased with the use of

subnets utilizing static addressing or by using a default gateway connection.

Graphical User Interface

If a CD-ROM is included with your ReachDSL router, it contains the ReachDSL 6351

graphical user interface (GUI). This Java application allows you to configure,

troubleshoot, and monitor the ReachDSL router. If the GUI is not provided, you can

configure the router using the console interface. See Configuration Setup on page 14.

Requirements

The GUI requires:

 J2SE Java Runtime Environment (JRE) Version 1.4 or later

 800 x 600 or greater display resolution

Installation Instructions: Microsoft Windows

The distribution CD includes Version 1.4.2 of the Sun JRE for x86 Windows. This is

suitable for:

 Windows 98

 Windows NT 4.0 (SP 6)

 Windows ME

 Windows XP

 Windows 2000

 Windows 2003 Server

Run the setupwin32.exe file on the distribution CD to install the ReachDSL 6351 GUI

and, if necessary, the JRE.

Start the GUI by clicking the ReachDSL_6351_GUI.exe icon in the Paradyne ReachDSL

6351 GUI folder created in the Programs Start Menu.

Installation Instructions: Linux

The distribution CD includes Version 1.4.2 of the Sun JRE for x86 Linux as a part of the

installation. If your hardware or version of Linux requires a different JRE, you need to

locate and install one.

Run the setuplinux.bin file on the distribution CD to install the ReachDSL 6351 GUI and,

if necessary, the JRE.

Start the GUI by clicking on ReachDSL_6351_GUI in the Programs menu.

Installation Instructions: Apple Macintosh

Installation of the GUI on a Mac requires Mac OS X and Java 1.4.x for Mac OS X to be

previously installed. Java 1.4.x is available at:

http://www.apple.com/java/

Run the setupmac.command file on the distribution CD to install the ReachDSL 6351

GUI.

Start the GUI by clicking on the ReachDSL_6351_GUI icon on the desktop.

Connecting the GUI to the Router

To use the GUI, you must supply the address of the router. Routers shipped with the GUI

are initialized with the address 192.168.158.1. Enter 192.168.158.1 in the entry box and

click on the Connect button. When the GUI is connected to the router, the button

changes to Disconnect. Click on the Disconnect button when you are ready to end the

session.

Click on:

 System View to view information about the router, such serial number, firmware

levels, and Wan and LAN addresses.

 Quick Config to configure RFC 1483 Encapsulation, the address of the Ethernet

port, PPP username and password, and DNS name servers.

 LAN to set the LAN IP address.

 IP Routes to add static routes.

 DHCP to enable and configure a DHCP server.

 NAT to enable and configure Network Address Translation and Network Address

Port Translation.

 PPP to enable and configure PPP over Ethernet.

 Alarms and Logs to view any alarms and system log entries.

Cables and Connectors

DSL Interface

The DSL interface uses a 6-pin, non-keyed modular

plug.

Use a CAT3, or better, cable for the DSL line.

RJ11 6-Pin Connector

Pin # Function

1 & 2 Not used

3DSL Ring

4DSL Tip

5 & 6 Not used

98-15304-01

6-Pin

RJ11 Plug

DSL

Cable

Pin #1

Pin #6

Console Interface

The Console connector uses 8-pin, non-keyed modular plugs and a DB9 adapter.

RJ45 8-Pin Connector

8-Pin Modular to DB9 Adapter Plug

Pin # Circuit Direction

1 Not used —

2 DTR Input to

Console port

3 TXD Input

4 & 5 Signal Ground —

6RXD Output

7DSR Output

8 Not used —

Modular

Pin # Circuit

DB9

Pin #

1RTS 7

2DTR 4

3TXD 3

4 & 5 Signal Ground 5

6RXD 2

7DSR 6

8CTS 8

97-15678

8-Pin

Plug

Console Port

Cable

Pin #1

Pin #8

98-16050

DB9

to RJ45

Ethernet Interface

The Ethernet interface connector uses an 8-pin, non-keyed modular plug. Use shielded

twisted-pair cables rated at CAT5 or better.

 To connect the router to an Ethernet hub, use a straight-through connection.

8-Pin Straight-through Connection

– or –

 To connect the router to a PC with an Ethernet NIC card, use an Ethernet crossover

cable.

Pin # Function

1 10/100BaseT TX D+

2 10/100BaseT TX D–

3 10/100BaseT RX D+

4 & 5 Not used

6 10/100BaseT RX D–

7 & 8 Not used

98-16055a

8-Pin

Plug

Ethernet

Cable

Pin #1

Pin #8

10/100BaseT TX D+

10/100BaseT TX D–

10/100BaseT RX D+

Not Used

10/100BaseT RX D–

Not Used

10/100BaseT TX D+

10/100BaseT TX D–

10/100BaseT RX D+

Not Used

10/100BaseT RX D–

Not Used

Function Pin # FunctionPin #

8-Pin Ethernet Crossover Cable

99-16518

Pin #1/2 = Orange/White

Twisted Pair

Pin #3/6 = Blue/White

Twisted Pair

Optional Wall Placement

The Hotwire 6351 ReachDSL Router is designed for tabletop placement. The router can

also be mounted on a wall.

To mount the router, you will need:

❑ Three #6 pan-head screws with anchors (for example, molly bolts, plastic or lead

anchors)

❑ Drill, and the correct size drill bit for the anchors

❑ Screwdriver

A template with the dimensions for the three screws is provided. See ReachDSL Router

Hardware Template on page 21.

Procedure

To mount the ReachDSL router:

1. Drill the correct size hole for the anchors and install them. Use the template to

gauge their placement.

2. Screw the pan-head screws into the installed anchors. Do not make them flush with

the wall. Leave enough clearance to hang the router housing from the screws.

Wall

Fasteners

99-16170-02

Page is loading ...

Paradyne Hotwire 6351 Installation Instructions Manual

Brand: Paradyne

Model: Hotwire 6351

Category: Routers

Type: Installation Instructions Manual

This manual is also suitable for

Hotwire ReachDSL 6351

Download PDF

report

Paradyne Hotwire 6351 Installation Instructions Manual

This manual is also suitable for

Paradyne Hotwire 6351 Installation Instructions Manual

Related papers

Other documents