Nuvo Simplese NV-A4DS-DC Installation guide

Nuvo
Brand
Nuvo
Model
Simplese NV-A4DS-DC
Category
Access control readers
Type
Installation guide

This manual is also suitable for

Nuvo Simplese NV-A4DS-DC is a high efficiency 200-watt stereo amplifier that can be used to power up to four zones of audio. Each zone can be independently controlled for volume, bass, and treble, and can be grouped with other zones to create a multi-room audio experience. The amplifier also features an IR output for controlling source devices, and a 12V trigger input for powering on and off external devices. With its versatile features and powerful sound, the Nuvo Simplese NV-A4DS-DC is an ideal choice for whole-home audio systems.

Nuvo Simplese NV-A4DS-DC is a high efficiency 200-watt stereo amplifier that can be used to power up to four zones of audio. Each zone can be independently controlled for volume, bass, and treble, and can be grouped with other zones to create a multi-room audio experience. The amplifier also features an IR output for controlling source devices, and a 12V trigger input for powering on and off external devices. With its versatile features and powerful sound, the Nuvo Simplese NV-A4DS-DC is an ideal choice for whole-home audio systems.

Simplese D Installation Guide
Step 1 Prewire:
Step 2 Allport Termination:
The Simplese D System uses Cat-5 wire for keypad control and either 2 or 4 conductor 16 gauge speaker wire. The
termination for the Cat-5 wire is standard 568A. Simplese uses an RJ-45 connector on each end of the Cat-5. Note that both the
speaker wire and Cat-5 are run to the Allport location at the equipment rack or cabinet.
Both the speaker wire and Cat-5 cables terminate into the backside of the Allport. The order of Cat-5
plug-ins is irrelevant to the operation of the system, but it is recommended that you label the Cat-5 wires for future reference. Follow
the zone and polarity labeling for the speaker wires. The final connection from the Allport is made with the Allport Cable supplied with
the Simplese D System.
™
SOURCE INPUT
L
R
L
R
1
2
3
4
L
R
ZONE 4
FIXED
VAR
LINE OUT
IR OUT
1
3
2
4
SYSTEM
LINK
RS232
STATU S
+12VON=
MUTE
=0V
SPEAKER AND DATA SIGNAL S
ALL PORT CONNECTION
Simplese
CON FORMS T O
UL ST D.650 0
CER TIFIE D TO
CAN /CSA STD .E600 65
303 3118
C
US
I
N
T
E
R
T
E
K
C
M
NuVo Tec hno log ies C incinnati Ohio USA
D
I
N
T
E
R
T
E
K
FOUR-SOURCE FOUR-Z ONE
100~240V 50~60Hz 85W
USE FOR SAT
OR CABLE
NORMAL
USE
56KHz38KHz
1
2
R
L
SENSITIVITY
OdBV = 1.0RMS
-12
+6
0
LEFT
+6
-12
RIGHT
0
AUDIO
INPUT
2
INPUT
OUTPUT
CONTROL
SPEAKER
MODELNV-P2100
HIGH EFFICIENCY200 WATT
STEREOAMPLIFIER
NuVoTechnologies Cincinnati Ohio. USA
120V
60HZ
WATTS
250
UNIT
ON
+12VDC
100mA
VOLTAGE
TRIGGER
3-30 VOLTS
AC OR DC
ON/OFF SWITCH
AUDIO AC/DC
POWER
MODE
OUTPUT POWER
8 OHM: 70W X 2
4 OHM: 100W X 2
CONTROL
USE ONLYWITH 250V FUSE
CD1
CD2
TNR1
TNR2
CD1
CD2
TNR1
TNR2
CD1
CD2
TNR1
TNR2
CD1
CD2
TNR1
TNR2
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Source 1
Tuner 1
Audio
Out
Source 2
Tuner 2
Audio
Out
Source 4
DVD
Audio
Out
Source 3
CD
Audio
Out
Simplese D
Wiring Diagram
Step 3 Connecting Audio Sources:
Step 4 IR Outputs:
Step 5 Keypad Setup:
Step 6 EQ Control, and Source Grouping:
The Simplese D system will accept up to four independent audio sources. This is done with stereo
RCA audio cables from the audio output on each source to the appropriate source input on the back of the Simplese amplifier.
The Simplese D System ships with four IR emitters for transferring IR data from the keypad receivers (located
under the volume button) to the IR receiver on each piece of source equipment. There are two separate IR output sections. The 38K
outputs are used most all audio sources. The exception to this frequency are cable and satellite boxes. They operate at a higher IR
carrier frequency around 56K. A second source one and two 56K output is available for these devices, see fig. 1. It is important that
the output being used for each source matches the source input number. The outputs are individual for each source to allow
independent source control. Simply plug the emitter into the appropriate IR output on the back of the Simplese amplifier and attach
the flasher end over the IR receiver on the source equipment.
Each keypad requires a specific zone setting to establish the keypad’s location. This setting is made on the
back of the keypad using an eight position rotary switch. To set the switch, place a small slot-head screwdriver in the slot in the
switch and turn it clockwise to the appropriate zone number 1-4, fig. 2. The remaining switch positions, 5-0 allow for an additional
keypad in each zone. Position 5 corresponds to zone 1, 6 to zone 2, 7 to zone 3, and 0 to zone 4.
The keypads can be used to set specific zone functions. These are bass and treble EQ
response, and source grouping. To change bass response, press the Mute button and Source 1 button simultaneously. Adjust the
bass level up or down by using the volume up and volume down buttons. The volume indicator LEDs will indicate the output level,
fig. 3. The default setting is flat. Adjusting treble is the same process and is accessed by pressing the Mute and Source 2 buttons.
Once the desired setting is made, press the Source button again and that returns the keypad to normal operation. Source grouping
is a featured that allows multiple zones in an open living space to always share the same source selection, but still retain individual
volume and on/off control. This is achieved by pressing Mute and Source 3. Volume Up enables the group function and Volume
Down disables the group function and causes the keypad to operate independently of all other groups, fig. 4.
Fig. 1: 38KHz and 56KHz IR Outputs
Fig. 2: Zone setting rotary switch
IR OUT
1
3
2
4
USE FOR SAT
OR CABLE
NORMAL
USE
56KHz38KHz
1
2
0
1
2
3
4
5
7
6
Fig. 3: Zone EQ Control
Fig. 4: Zone Group Settings
Step 7 Final Setup:
Simplese D Specifications
Once the sources are plugged in and the keypads are set and installed you should be ready to power on any
of the zones and enjoy music from any of the sources.
Zones 1-6 Power Amplifier Outputs System
Power Requirements
Preamplifier Section
Physical Specifications
Source Inputs 1-4
Emitter Outputs
Continuous Average Output Power 30W (15W x 2) System On 12V @ 50mA
Two channels driven 30-20kHz @1% THD External Mute 3-12V DC
Rated Distortion (1/2 power) 0.40%
Rated Impedance 6 Ohms
Damping Factor 50+ Power Supply 90-260VAC
50/60Hz
Frequency Response (20-20kHz) " 2dB Power Consumption all channels 140W
driven to full-rated power
Cower Consumption average 30W
Variable output 0-600mV operating conditions
Fixed output 600mV Power Consumption no signal 10W
Impedance 600 Ohms
Unit Size Millimeters 44 x 430 x 270
input Impedance 10K Unit Size Inches 1.75 x 17 x 10.625
Input Sensitivity for rated power 300mV RMS Unit Weight Kilograms 2.95
Input Overload 3V RMS Unit Weight Pounds 6.5
NuVo reserves the right to change specifications
Source Outputs 4 without notice.
Output Drive Current 100mA
Output Drive Voltage 12V
Compatible with single and dual emitters
+
VOLUME
FLAT
-4 dB
+4 dB
+6 dB
+8 dB
-6 dB
-8 dB
VOLUME
Group Disabled
Group Enabled
  • Page 1 1
  • Page 2 2
  • Page 3 3

Nuvo Simplese NV-A4DS-DC Installation guide

Nuvo
Brand
Nuvo
Model
Simplese NV-A4DS-DC
Category
Access control readers
Type
Installation guide
This manual is also suitable for

Nuvo Simplese NV-A4DS-DC is a high efficiency 200-watt stereo amplifier that can be used to power up to four zones of audio. Each zone can be independently controlled for volume, bass, and treble, and can be grouped with other zones to create a multi-room audio experience. The amplifier also features an IR output for controlling source devices, and a 12V trigger input for powering on and off external devices. With its versatile features and powerful sound, the Nuvo Simplese NV-A4DS-DC is an ideal choice for whole-home audio systems.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents