CNB G2960NF/G2960PF Owner's manual

CNB
Brand
CNB
Model
G2960NF/G2960PF
Category
Security cameras
Type
Owner's manual

CNB G2960NF/G2960PF is a high-performance COLOR VIDEO CAMERA. It provides a wide range of features and functions to meet the needs of various security and surveillance applications. Some of the key capabilities of this device include:

  • Color CCD: Captures clear and detailed images, even in low-light conditions.
  • Super Signal Noise Reduction (SSNR): Reduces noise and improves image quality, especially in low-light environments.
  • Digital Signal Processing (DSP): Enhances image quality by reducing noise, improving contrast, and adjusting colors.
  • On-Screen Display (OSD): Provides an intuitive user interface for easy setup and operation.

CNB G2960NF/G2960PF is a high-performance COLOR VIDEO CAMERA. It provides a wide range of features and functions to meet the needs of various security and surveillance applications. Some of the key capabilities of this device include:

  • Color CCD: Captures clear and detailed images, even in low-light conditions.
  • Super Signal Noise Reduction (SSNR): Reduces noise and improves image quality, especially in low-light environments.
  • Digital Signal Processing (DSP): Enhances image quality by reducing noise, improving contrast, and adjusting colors.
  • On-Screen Display (OSD): Provides an intuitive user interface for easy setup and operation.
Digital Color Camera Series
P/N : 3810-0093A
(Ver.0612E)
Color Video Camera Series
Design and specifications are subject to
change without notice.
4
2
5
6 7
8 9
10 11
12 13
3
14 15
16 17
1918
2120
2322
24 25
26 27
28 29
3130
3332
3534
36 37
38 39
40 41
4342
4544
4746
48 49
50 51
52 53
5554
COLOR VIDEO CAMERA
Color CCD
COLOR VIDEO CAMERA
Color CCD
OWNER'S MANUAL
DIGITAL CAMERA SERIES
COLOR VIDEO CAMERA
Super Signal Noise Reduction
SSNR
SSNR
On-Screen Display
OSD
OSD
DSP
•
O
S
D
(
O
n
S
c
r
e
e
n
D
i
s
p
l
a
y
)
•
S
u
p
e
r
D
i
g
i
t
a
l
N
o
i
s
e
R
e
d
u
c
t
i
o
n
•
5
3
0
T
V
L
i
n
e
s
DC 12V
Class 2 Only
MENU
POWER
VIDEODC
VIDEO OUT
CONTROL
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
WARNING
The manufacturer could void the user's authority to operate the equipment.
CAUTION - To prevent electric shock and risk of fire hazards:
Do NOT use power sources except for that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should abide to all local codes.
CAUTION!
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Explanation of two Symbols
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance-
(servicing) instructions in the literature accompanying the appliance.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"
. User Information
1. SAFETY INSTRUCTIONS
2. PRECAUTIONS
3. FEATURES
4. NAME AND FUNCTIONS
5. OPERATING CAMERA
6. INSTALLATION (LENS)
5
6
7
8
11
38
39
40
7. COMPOSITION
8. CONNECTIONS
9. SPECIFICATIONS
41
42
43
45
46
46
48
Before using this camera, please read this operation manual carefully to obtain
the best result and keep this manual for future reference.
Thank you for purchasing this COLOR VIDEO CAMERA.
. Lens Connector
. Control Jack
. Back-focus Adjustment
. Mounting a Lens
. AC 24V / DC 12V Input Model
. DC 12V Input Model
. Contents
Handling
Do not disassemble the camera and never touch
parts inside the camera.
Be sure the ambient temperature is less than
40 in installation intended for long ter m
continuous operation.
Avoid installing in a humid or dusty place.
Avoid installing in places where there are
strong magnetic fields and electric signals.
Avoid installing in places where the camera
would be subject to strong vibrations.
Never expose the camera to rain and water.
Installation and storage
Do not point the camera at the sun. This could
damage the camera whether it is operating or not.
Do not install the camera where the temperature
could exceed the allowable range.
Do not drop the camera or subject it to shocks
and vibrations to avoid possible damage.
When attaching or removing the lens, handle
with care in order to that moisture and dust do
not enter the camera.
2. PRECAUTIONS
Read Instructions
Read all of the safety and operating instructions
before using the product.
Installation
Do not place this product on an unstable cart, stand,
or table. The product may fall causing serious injury
to a child or adult, and damage to the product.
Use only with a cart or stand recommended by the
manufacturer, or sold with the product.
Mounting should follow the manufacturer's instructions,
and should use a mounting accessory recommended
by manufacturer.
Power source
This product should be operated only from the type
of power source indicated on the marking label.
If you are not sure of the type of power supplied to
your home, consult your dealer or local power
company.
Retain Instructions
Save this instructions for later use.
Cleaning
Unplug this appliance from wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Water and Moisture.
Do not use this product near water or moisture.
(For example. near a bathtub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool,etc)
1. SAFETY INSTRUCTIONS
High sensitivity 1/3 Inch Sony Super HAD CCD Pick-Up
Min lllumination : 0.3 Lux (Color)
0.02 Lux (B/W, DSS Off)
0.0005 Lux (B/W, DSS On)
Day & Night mode selectable.
High performance menus for functions
SSNR (Super Signal Noise Reduction)
It has an assistant reducing image noise efficiently and It shows clear and
sharp image display even in the dark
• Privacy zone selectable.
• Motion detection selectable.
• Super BLC selectable.
• Sharpness enhanced adjustable.
• Flickerless On/Off
• SENS-UP (DSS, Electronic Sensitivity-Up)
3. FEATURES
5. OPERATING CAMERA
LENS
SHUTTER
WHITE BALANCE
BACKLIGHT
AGC (Auto Gain Control)
SSNR
(Super Signal Noise Reduction)
SENS-UP
SPECIAL
EXIT
• MANUAL • DC/VIDEO
• ESC • MANUAL • FLK
• ATW • MANUAL • AWC
• OFF • LOW • MIDDLE • HIGH
• OFF • LOW • MIDDLE • HIGH
• OFF • LOW • MIDDLE • HIGH
• OFF • AUTO
• CAMERA ID • COLOR • DZOOM • SYNC
• MOTION DET • PRIVACY • MIRROR
• SHARPNESS • RESET • RETURN
SETUP MENU
1
1
1
1
. Lens Connector Plug (E-4-191J-100)
. Lens Mount Cap
. C-mount Adapter
. Owner's Manual
!
Design and specifications are subject to change without notice.
This color video camera is designed to output video signals conforming
to the NTSC(PAL) standard. So that it cannot be used with video recorder
or color monitors which use color systems other than NTSC(PAL).
The lens mount cap and C-mount adapter are attached when supplied.
7. COMPOSITION
DC 12V
Class 2 Only
MENU
POWER
VIDEODC
VIDEO OUT
CONTROL
Connect the video output of the camera to the video input of a monitor or other equipment.
When using a "loop through" connection of two or more monitors, set the 75 switch of only the final
monitor to on. Determine the type of cable according to the distance of the connected equipment.
DC 12V
Power Source
NOTE
Do not turn any component's power
on until all connections are completed.
To Power input terminal
To Video input connector
8. CONNECTIONS
NTSC PAL
2:1 Interlace Transfer 1/3 Inch Super HAD CCD
768 (H) x 494 (V) 752 (H) x 582 (V)
Composite: 1.0Vp-p, 75, Unbalanced
Internal Sync
More than 50dB (AGC OFF)
530 TV Lines
0.3 Lux (AGC ON), 0.02Lux (B/W DSS Off), 0.0005Lux (B/W DSS On)
C/CS Mount
Auto / Manual / Flickerless
x128~1/60~1/120,000 Sec.[NTSC], x128~1/50~1/120,000 Sec.[PAL]
ATW (1,900K~10,500K) / AWC / MANUAL
OFF / LOW / MIDDLE / HIGH
Signal System
Image Sensor
Effective Pixels
Video Output
Sync. System
Luminance S/N Ratio
Horizontal Resolution
Sensitivity (F1.2)
Lens Mount
Electronic Shutter
White Balance
BLC, AGC
High ResolutionMODEL
9. SPECIFICATIONS
OFF / LOW / MIDDLE / HIGH
ON / AUTO / B/W / EXT
8 x (On / Off)
ON / OFF (4 Programmable Zone)
ON / OFF (4 Programmable Zone)
ON / OFF (Horizontal)
ON / OFF (Level Adjustable)
DC Iris / Video Iris / Manual Lens
DC 12V(10V~15V)
180mA / 2.2W (Max)
-10~+50(Recommendation:-5~+40)
-20~+60
65(W)x59.6(H)x122.5(D)mm / 59(W)x58(H)x123.75(D)mm
Approx. 430g
SSNR (Super Signal Noise Reduction)
Color (D&N)
D-ZOOM
Motion Detection
Privacy
Mirror
Sharpness
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature
Storage Temperature
External Dimensions
Weight
DC 12V Input Model
NTSC PAL
2:1 Interlace Transfer 1/3 Inch Super HAD CCD
768 (H) x 494 (V) 752 (H) x 582 (V)
Composite: 1.0Vp-p, 75, Unbalanced
Internal Sync / Line-Lock Sync
More than 50dB (AGC OFF)
530 TV Lines
0.3 Lux (AGC ON), 0.02Lux (B/W DSS Off), 0.0005Lux (B/W DSS On)
C/CS Mount
Auto / Manual / Flickerless
x128~1/60~1/120,000 Sec.[NTSC], x128~1/50~1/120,000 Sec.[PAL]
ATW (1,900K~10,500K) / AWC / MANUAL
OFF / LOW / MIDDLE / HIGH
Signal System
Image Sensor
Effective Pixels
Video Output
Sync. System
Luminance S/N Ratio
Horizontal Resolution
Sensitivity (F1.2)
Lens Mount
Electronic Shutter
White Balance
BLC, AGC
High ResolutionMODEL
9. SPECIFICATIONS
OFF / LOW / MIDDLE / HIGH
ON / AUTO / B/W / EXT
8 x (On / Off)
ON / OFF (4 Programmable Zone)
ON / OFF (4 Programmable Zone)
ON / OFF (Horizontal)
ON / OFF (Level Adjustable)
DC Iris / Video Iris / Manual Lens
AC 24V (20V~28V) or DC 12V (10V~15V)
330mA / 4W (Max)
-10~+50(Recommendation:-5~+40)
-20~+60
65(W)x59.6(H)x122.5(D)mm / 59(W)x58(H)x123.75(D)mm
Approx. 430g
SSNR (Super Signal Noise Reduction)
Color (D&N)
D-ZOOM
Motion Detection
Privacy
Mirror
Sharpness
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature
Storage Temperature
External Dimensions
Weight
AC 24V / DC 12V Input Model
WITH A ZOOM LENS
1) Fully open the aperture and set the lens to the maximum tele-photo position. Then turn the focus ring to focus.
In the case of an auto-iris lens only, shoot a comparatively dark object so that the aperture is fully open.
2) Set the lens to its maximum wide-angle position.
3) Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.
4) After adjusting the back-focus, tighten the back-focus screw.
5) Repeat step 1)~3) until the difference between focusing position 1) and 2)becomes smallest.
CAUTION : Do not forcibly turn back-focus screw, it could cause damage to the camera.
When a lens is mounted, adjustment of the back-focus may sometimes be required.
Adjust the lens focus ring when the correct focus cannot be obtained.
WITH A FIXED-FOCUS LENS
1) Fully open the aperture and set the focus ring to ""(infinity).
In the case of an auto-iris lens only, shoot a comparatively dark object so that the aperture is fully open.
2)
Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.
3) After adjusting the back-focus, tighten the back-focus screw.
Back-focus Adjustment
1
Remove the lens mount cap from the camera.
2
Attach or remove the C-mount adapter depending on the lens to be used.
3
Attach the lens to the lens mount. Secure it so that it does not become loose.
4
If the lens has an auto-iris mechanism, connect the lens cable to the lens connector.
- When installing a video-iris lens, lens switch should be set to VIDEO position.
- When installing a galvanometric-iris lens, lens switch should be set to DC position.
- If the adapter is attached so tightly that it is difficult to remove it.
(Keep the C-mount adapter for possible future use.)
Mounting a Lens
Video Type lens : Set lens Switch to Video. Connect the lens cable of a video Type lens.
If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.
DC type lens : Set lens switch to DC. Connect the lens cable of a DC(Galvanometric) type lens.
If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.
Pin Assignment :
#
1
#
3
#
2
#
4
Pin No.
#1
#2
#3
#4
Signal
+9V DC
N.C
Video(1.0Vp-p, high impedance, no sync)
GND
VIDEO Iris Type Lens
Pin No.
#1
#2
#3
#4
Signal
Damping coil (
-
)
Damping coil (+)
Drive coil (+)
Drive coil (
-
)
DC Iris Type Lens
When using an auto-iris lens, install the accessory lens plug
on the lens cable as follows.
NOTE
After installing the connector plug, connect it to
the lens connector on the rear panel of camera.
Lens Connector
- DOWN Button
- UP Button
- LEFT Button
- RIGHT Button
- MENU(SET) Button
Use five buttons on rear side of the camera.
SETUP
- Press the MENU button to access the setup mode.
• Select the status using the , , , button.
• Move the cursor to character enter location by
using the button.
Setting up the Menu
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
MANUAL
ESC
ATW
OFF
LOW
LOW
OFF
1. Press the MENU button to access the SETUP mode.
• SETUP menu is displayed on the monitor screen.
2. Select the desired feature using the UP or DOWN button.
• Each time you press the UP or DOWN button, the arrow indicator moves UP or DOWN.
• Move the arrow indicator the desired feature item.
3. Change the status of the selected feature using the LEFT or RIGHT button.
• If you Press RIGHT or LEFT button, it appears available status. Press the button when gets desired feature.
4. When completed, move the arrow indicator to 'EXIT' and press the MENU button.
Main Menu -
SETUP
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
---
AWC
HIGH
HIGH
LOW
AUTO
!
You can access submenu using MENU button.
For the mode with '---', you may not access submenu.
NOTE
Main Menu -
LENS
1) Setting up the LENS
Select the lens pressing the RIGHT button.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
MANUAL
FLK
AWC
HIGH
OFF
---
---
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
---
AWC
HIGH
HIGH
LOW
AUTO
On the SETUP menu screen, move the ar row indicator to the lens using the UP or DOWN button.
Select the desired feature using the LEF T or RIGHT button.
Main Menu -
WHITE BALANCE
3) WHITE BAL. (White Balance)
When you need to control the color on the screen, use 'WHITE BALANCE' function.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
---
AWC
HIGH
OFF
---
---
P ress the MENU button to display the SETUP menu and move the arrow indicator to 'WHITE BAL.'
using the UP or DOWN button.
Set 'WHITE BAL.' T o the desired mode using LEFT or RIGHT button.
ATW(Auto Tracking White Balance): When color temperature is 1,900 K~10,500 K, select this mode.
(ex. A fluorecent lamp, outdoor)
AWC(Auto White Balance Control): The white balance is automatically adjusted in a specific environment.
In order to obtain the best result, press the set button while the camera focuses on white paper.
If the environment including the light source is changed, you have to adjust the white balance again.
2) Shutter status and speed control
You can control brightness of the screen by the shutter speed.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
---
AWC
HIGH
OFF
---
---
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
MANUAL
FLK
AWC
HIGH
OFF
---
---
Press the MENU button to display the setup menu and move the arrow indicator to 'SHUTTER' using the UP or DOWN button.
Set 'SHUT TER' to the desired mode using the LEFT or RIGHT button.
---
: Deactivation
FLK: Flickerless mode
- NTSC (1/100)
- PAL (1/120)
Main Menu -
SHUTTER SPEED CONTROL(1)
!
AUTO IRIS LENS(DC TYPE)is recommended than MANUAL LENS.
Some lens can make a malfunction according to the BRIGHTNESS LEVEL.
NOTE
When DC LENS selected, press MENU button to control the BRIGHTNESS.
Brightness
Press SET to Return
BRIGHTNESS 25
Main Menu -
SHUTTER SPEED CONTROL(2)
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
MANUAL
MANUAL
AWC
HIGH
OFF
---
---
MANUAL : When setting shutter speed manually.(Only for manual LENS mode)
You can select speed from
- NTSC (x128~x2, 1/60~1/120,000 sec.)
- PAL (x128~x2, 1/50~1/120,000 sec)
SHUTTER
Press SET to Return
MANUAL 1/60
Main Menu -
SSNR
6) SSNR (Super Signal Noise Reduction)
SSNR reduces the noise on the screen.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
---
AWC
HIGH
OFF
---
---
P ress the MENU button to display the SETUP menu and move the arrow indicator to 'SSNR' using the UP or
DOWN button.
SET 'S SNR' to the desired mode using the LEFT or RIGHT button.
OFF : Deactivation
LOW : Low reduction
of the noise
MIDDLE : Middle
reduction of the noise
HIGH : High reduction
of the noise
!
Afterimage may appear with SSNR activated.
When selected 'AGC' menu OFF, SSNR doesn't work.(
---
)
If you change the 'AGC' menu from AGC-L to AGC-H, sensitivity is
increasing as well as noise on the screen.
NOTE
MANUAL : To fine adjust, select the Manual mode. You can increase or decrease the red
or blue factor while monitoring the difference on the screen. Set to 'MANUAL'
mode and press the MENU button, lncrease or decrease the value for RED(R-Gain)
and BLUE(B-Gain), watching the color of the picture, and press the MENU button
when you obtain the best color.
!
Proper White Balance may not be obtained under the following
conditions, in these cases select the AWC mode.
- When the scene contains mostly high color temperature object,
such as a blue sky or sunset.
- When the scene is dim.
- If your camera faces fluorescent lamp directly or is installed in the
place of the changing illumination.
NOTE
When completed, press 'MENU'
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
MANUAL
ESC
AWC
HIGH
OFF
---
---
ESC : You can control
the BRIGHTNESS.
!
Don't expose the camera to fluorescent lamp directly not to get unstable
image in the internal synchronization modes.
When the SHUTTER menu is set to FLK mode. SENS-UP dose not operate.
NOTE
Brightness
Press SET to Return
BRIGHTNESS 25
Main Menu -
AGC
5) AGC (Auto Gain Control)
AGC is to get bright picture. Higher GAIN level, getting brighter screen. But you can get noise increase.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
---
AWC
HIGH
OFF
---
---
P ress the MENU button to display the SETUP menu and move the arrow indicator to 'AGC' using the
UP or DOWN button.
SET 'AGC' to the desired mode using the LEF T or RIGHT button.
OFF LOW MIDDLE HIGH
8) SPECIAL
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
---
AWC
HIGH
OFF
---
---
SPECIAL
CAMERA ID
COLOR
DZOOM
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
ON
---
OFF
INT
OFF
OFF
OFF
ON
Press the MENU button to display the SETUP menu and move the arrow indicator 'SPECIAL' using the UP or DOWN button.
SET 'SPECIAL' to the desired mode using the LEF T or RIGHT button.
Press the MENU button to display the SETUP menu and move the arrow indicator to 'CAMERA ID' using the UP or DOWN button.
SET 'ON' using the LEF T or RIGHT button.
P ress the MENU button to
access the SETUP mode.
Menu [SPECIAL]-
CAMERA ID (1)
CAMERA ID
P ress the MENU button.
: Configure Zoom magnification rate from x1 ~ x8 using this feature.
Please select the ZOOM R ATE from x1 ~x8.
Menu [SPECIAL]-
DZOOM
DZOOM
SPECIAL
CAMERA ID
COLOR
DZOOM
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
ON
---
OFF
INT
OFF
OFF
OFF
ON
P ress the MENU button to display the setup menu and move the arrow indicator to 'COLOR' using the
UP and DOWN button.
: You can choose color and B/W mode electronically.(OPTION)
SET 'COL OR' to the desired mode using the LEFT or RIGHT button.
---
: Deactivation
ON : Color mode
AUTO : According to the
input luminance level, IR
Cut Filter is automatically
switched to the appropriate
mode for daytime or night-
time. The COLOR mode is
operated for daytime, and
it converts to BW mode
for night-time.
B/W : BW mode. Please SETUP button to turn on or off the burst signal on BW mode.
EXT : It enables user to control DAY or NIGHT mode by external input signal. (Refer to P44)
COLOR
Menu [SPECIAL]-
SYNC
SPECIAL
CAMERA ID
COLOR
DZOOM
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
ON
OFF
---
INT
OFF
OFF
OFF
ON
P ress the MENU button to display the setup menu and move the arrow indicator to 'SYNC' using the
UP and DOWN button.
: Two Synchronization modes are available Internal and External Line-Lock.
In Line-Lock mode, it synchronous the video signal between cameras without a synchronous generator.
The line-lock synchronization is only used in the area of 60Hz(NTSC Type)/ 50Hz(PAL Type)
SET to the desired mode using the LEF T or RIGHT button.
INT : Internal
synchronization
L/L : If you choose
'L/L', you can adjust
the desired phase.
- Press the MENU button.
- You can adjust the
desired phase from
0 to 359.
!
When it used in AC power, L/L mode can be used.
In DC12V, the SYNC is fixed to 'INT' mode.
NOTE
SYNC
Menu [SPECIAL]-
PRIVACY
SPECIAL
CAMERA ID
COLOR
DZOOM
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
ON
---
OFF
INT
OFF
OFF
OFF
ON
P ress the MENU button to display the setup menu and move the arrow indicator to 'PRIVACY' using the
UP and DOWN button.
: To conceal the areas you do not wish to appear on the screen.
SET 'PRIV ACY' to the desired mode using the LEFT or RIGHT button.
OFF : Deactivation
ON : PRIVACY mode
activated
- Press the MENU button and
then set the area's bounds
with the method like MOTION DET. Set
- Set 'ON' using LEFT or
RIGHT button.
- Move the arrow indicator
to area you want to mask.
- Press the MENU button.
PRIVACY
: This mode reverses the image horizontally.
Menu [SPECIAL]-
MIRROR
SPECIAL
CAMERA ID
COLOR
DZOOM
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
ON
---
OFF
INT
OFF
OFF
OFF
ON
P ress the MENU button to display the setup menu and move the arrow indicator to 'MIRROR' using the
UP and DOWN button.
SET 'MIRROR' to desired mode using the LEF T or RIGHT button.
OFF : Deactivation
ON : Reverse image
LEFT and RIGHT.
MIRROR
Menu [SPECIAL]-
MOTION DETECTION
SPECIAL
CAMERA ID
COLOR
DZOOM
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
ON
---
OFF
INT
OFF
OFF
OFF
ON
Press the MENU button to display the setup menu and move the arrow indicator to 'MOTION DET' using the UP and DOWN button.
: The camera detects an object's movement by sensing disparity of outline,
and level of brightness and color.
SET 'MOTION DET' to the desired mode using the LEF T or RIGHT button.
OFF : Deactivation the
motion detection mode.
ON : Any motion in the
selected area is observed.
- Please select the area you
wish to observer from the
4 different areas.
- Move the arrow indicator
to 'AREA SET' using UP
and DOWN button, and
then press the MENU button.
- Press MENU button.
MOTION DET
MOTION DETECTION
Press SET to Return
AREA SEL
AREA STATE
TOP
DOWN
LEFT
RIGHT
AREA1
ON
10
25
20
40
Menu [SPECIAL]-
SHARPNESS
P ress the MENU button to display the setup menu and move the arrow indicator to 'SHARPNESS' using
the UP and DOWN button.
SET 'SHARPNES S' to the
desired mode using the
LEFT or RIGHT button.
SPECIAL
CAMERA ID
COLOR
DZOOM
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
ON
---
OFF
INT
OFF
OFF
OFF
ON
OFF : Deactivation.
SHARPNESS
SHARPNESS
Press SET to Return
LEVEL
8
ON : SHARPNESS
control mode(level 0~31)
when the level is up, the
sharpness will make
image clear.
Please control the level
as you want to get.
Menu [SPECIAL]-
RESET / RETURN
RESET
: Save the setting of SPECIAL function, and then move to SETUP menu.
RETURN
: To reset your camera to the factory default setting.
: The outline of the video image becomes cleaner and more distinctive as the level of SHARPNESS increases.
PRIVACY
Press SET to Return
AREA SEL
AREA STATE
AREA TONE
TOP
DOWN
LEFT
RIGHT
AREA1
ON
80
10
25
20
40
SPECIAL
CAMERA ID
COLOR
DZOOM
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN
ON
---
OFF
INT
OFF
ON
OFF
ON
Please adjust the size of the area to be obser ved by using the UP, DOWN, LEFT or RIGHT button.
Max Min
MOTION DETECTION
Press SET to Return
AREA SEL
AREA STATE
TOP
DOWN
LEFT
RIGHT
AREA1
ON
10
25
20
40
13
18
5
6
Main Menu -
BACKLIGHT
4) BACKLIGHT (Back Light Compensation)
When there is a strong backlight behind the object, clear images of the background as well as the object can
still be obtained by using the BACKLIGHT function.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
---
AWC
HIGH
OFF
---
---
Press the MENU button to display the SETUP menu and move the arrow indicator to 'BACKLIGHT' using the UP or DOWN button.
SET 'BACKLIGHT' to the desired mode using the LEF T or RIGHT button.
OFF LOW MIDDLE HIGH
BLC ON BLC OFF
1) CAM TITLE (Camera Title)
If the CAMERA ID feature is set to 'OFF', the name will not displayed in the monitor.
P ress the MENU button to access the SETUP mode.
SET 'ON' using the LEF T or RIGHT button.
Y ou can enter up to 15 characters.
• Move the cursor to character-enter location by using the LEFT or RIGHT button.
• Select the desired character by using the UP or DOWN button.
• Press the MENU button to confirm the blinking character. The first character is saved and the cursor
in the bottom of the screen moves to the next position.
• Repeat steps a, b and c until you create the full name you want.
• Select the position at which the CAMERA ID will be located on the screen.
- Move the cursor to 'POS' and press the MENU button.
-
Select the position by using the 4-directional buttons, then press the MENU button to confirm the position.
• When completed, move the cursor to 'END' and press the MENU button.
Menu [SPECIAL]-
CAMERA ID (2)
CAMERA ID
Press SET to Return
CAM TITLE
CAM ID No.
EXIT
ON
0
DZOOM
Press SET to Return
RATE
ZOOM RATE X1.0
8
Menu [SPECIAL]-
COLOR
!
If the level goes up excessively, you can get the unnatural image with noise.
NOTE
2) CAM ID No. (Camera ID No.)
Camera ID can be specified using numbers from 0 to 255 by using the LEF T or RIGHT button.
Display the camera's ID.
!
If you make a mistake while entering name Move the cursor to 'CLR', press 'SET'
button. After erasing the character from right to left. Correct the character again.
NOTE
CAMERA ID
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-
. 0123456789
CLR POS END
_______________
4. NAME AND FUNCTIONS
Holder Screw Hole
Used to install the camera on an optional
holder.(Tripod or Bracket)
The optional holder must be equipped with
the screw specified as shown right.
CS-Mount Holding Screw
Used to readjust back focus of the camera.
There are two back focus lock screws.
These must be loosened before the camera
may be back focused.
Loosen the lock screws to turn the CS-mount
lens adaptor, and tighten the lock
screws after adjustment.
Auto Iris Lens Connector
Used to connect Auto Iris Lens plug.
C-Mount Lens Adapter
Used to attach C-mount lens.
CS-Mount Lens Adapter
Used to attach CS-mount lens.
1/4"- 20 UNC (20 THREAD)
L : 4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
L
Lens Selection Switch
Used to choose DC or VIDEO or ELC according to the type of your Lens.
POWER Input Terminal
Used to connect an AC 24V or DC 12V power source.
Used to connect a DC 12V power source.
VIDEO OUT Jack
Used to connect an external video monitor in jack.
Remote Jack (See page 43)
Used to connect remote plug.
Function Setup Button
Functions can be setup using 5 buttons on the camera's rear panel.
MENU Buttons : Used to access menu mode.
Also used to escape menu mode.
UP / DOWN Buttons : Used to choose the desired
menu item. It also moves the cursor up or down in
the menu screen.
LEFT/RIGHT Buttons: Used to change the parameter
of the selected menu item. It also moves the cursor
the left of right in the menu screen.
MENU
Please insert a lens cable when using the DC iris lens or
Video iris lens.
Lens select switch on the rear pannel should be set to
DC or VIDEO position when using
the AUTO iris lens.
When using the VIDEO type lens, please adjust a brightness
of image with volume attached with the lens.
When using the DC type lens, please
adjust a brightness of image by setup
menu on the rear panel.
6. INSTALLATION (LENS)
Control Jack
VIDEODC
VIDEO OUT
CONTROL
1 2 3 4 5
TD
RD
GND
NAME
1. Frame GND
2. RD
3. TD
4. DTR
5. Signal GND
6. DSR
7. RTS
8. CTS
9. RI
PC Interface
Tx +
Tx
-
Rx +
Rx
-
3
4
5
2
1
8
9
7
6
R +
R
-
T +
T
-
RS-232C D-Sub Connector (PC)
RS-232C TO RS-422 Converter
No. Function
1
2
3
4
5
R+ (RS-485)
R
-
(RS-485)
MOTION DET. OUTPUT "H"
GND
DAY/NIGHT INPUT(EXT) "L"
: It is a terminal that controls the function of the camera at long distance.
Remote Input Jack (RS485)
: It is the function that can be switched to DAY Mode or NIGHT Mode by receiving the Day/Night
on/off signal from external light sensor or IR LED LAMP.
When Day / Night Mode is set " EXT" on the OSD menu of the Camera.
DAY / NIGHT External Input
Motion Det Output
3sec
OV
There is no motion
+3V
There is motion
3
4 GND
Motion Det Out
Open contact : DAY
Close contact : NIGHT
4
5 D/N ON (EXT)
GND
MD(Motion Detection) Output Signal Level(less than 10mA)
DC 12V
F unction
Setup Button
Video Out Jack
R emote Jack
L ens Selection
Swicth
P ower Input
Terminal
Class 2 Only
MENU
POWER
VIDEODC
VIDEO OUT
CONTROL
DC 12V Input Model
MENU
POWER
VIDEODC
VIDEO OUT
CONTROL
AC 24V / DC 12V Input Model
Class 2 Only
AC 24V
/
DC 12V
7) SENS-UP (Sensitivity-Up)
SENS-UP makes camera's sensitivity up so you can get a bright, clear screen image by automatically detecting
changes in the level of light in low light level conditions.
SETUP
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
SSNR
SENS-UP
SPECIAL
EXIT
DC
---
AWC
HIGH
OFF
---
---
Press the MENU button to display the SETUP menu and move the arrow indicator to 'SENS-UP' using the
UP or DOWN button.
SET 'SENS-UP' to the desired mode using the LEF T or RIGHT button.
AUTO : When your
camera is under night
or low-lighting level.
Select this mode.
OFF : Deactivation
!
If you press MENU button at 'AUTO' menu, you can control the lowlight
action maximum magnifications. (x2~x128)
When increasing the magnifications in case of SENS-UP activated.
It may appear noise, spots, whitish, This is not out of order.
Expander the magnifications, you can get the brighter screen as well as the afterimage.
NOTE
Main Menu -
SENSE-UP
When the SHUTTER menu is set to FLK mode. SENS-UP dose not operate.
. Memo
  • Page 1 1

CNB G2960NF/G2960PF Owner's manual

CNB
Brand
CNB
Model
G2960NF/G2960PF
Category
Security cameras
Type
Owner's manual

CNB G2960NF/G2960PF is a high-performance COLOR VIDEO CAMERA. It provides a wide range of features and functions to meet the needs of various security and surveillance applications. Some of the key capabilities of this device include:

  • Color CCD: Captures clear and detailed images, even in low-light conditions.
  • Super Signal Noise Reduction (SSNR): Reduces noise and improves image quality, especially in low-light environments.
  • Digital Signal Processing (DSP): Enhances image quality by reducing noise, improving contrast, and adjusting colors.
  • On-Screen Display (OSD): Provides an intuitive user interface for easy setup and operation.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents