BenQ mp 771 User manual

Category
Data projectors
Type
User manual

This manual is also suitable for

Welcome
MP771 Digital Projector
User Manual
Table of contents2
Table of contents
Important safety
instructions .........................3
Introduction........................7
Projector features .................................. 7
Shipping contents.................................. 8
Projector exterior view.......................... 9
Controls and functions ....................... 10
Positioning your projector14
Choosing a location............................. 14
Obtaining a preferred projected image
size........................................................ 15
Connection .......................18
Connecting a computer or monitor... 18
Connecting Video source devices....... 21
Operation ..........................26
Starting up the projector..................... 26
Using the menus.................................. 27
Securing the projector......................... 28
Switching input signal......................... 31
Adjusting the projected image ............ 32
Magnifying and searching for details on
the projected picture ........................... 33
Selecting the aspect ratio..................... 34
Optimizing the image.......................... 35
Setting the presentation timer ............ 39
Remote paging operations .................. 40
Hiding the image ................................. 41
Freezing the image............................... 41
Utilizing FAQ function ....................... 42
Locking control keys ........................... 42
Operating in a high altitude
environment.........................................43
Creating your own startup screen .......43
Adjusting the sound.............................44
Personalizing the projector menu
display...................................................44
Shutting down the projector ...............45
Menu operation ...................................46
Maintenance......................53
Care of the projector............................53
Lamp information................................54
Troubleshooting ...............60
Specifications ....................61
Projector specifications........................61
Dimensions...........................................62
Timing chart.........................................63
Warranty and Copyright
information.......................65
Regulation statements ......66
Important safety instructions 3
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1. Please read this manual before you
operate your projector. Save it for
future reference.
2. Do not look straight at the projector
lens during operation. The intense
light beam may damage your eyes.
3. Refer servicing to qualified service
personnel.
4. Always open the lens shutter or
remove the lens cap when the
projector lamp is on.
5. In some countries, the line voltage is
NOT stable. This projector is designed
to operate safely within a mains
voltage between 100 to 240 volts AC,
but could fail if power cuts or surges
of ±10 volts occur. In areas where the
mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a
power stabilizer, surge protector or
uninterruptible power supply (UPS).
6. Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire. To
temporarily turn off the lamp, press
BLANK on the projector or remote
control.
Important safety instructions4
Safety Instructions (Continued)
7. The lamp becomes extremely hot
during operation. Allow the
projector to cool for approximately
45 minutes prior to removing the
lamp assembly for replacement.
8. Do not operate lamps beyond the
rated lamp life. Excessive operation
of lamps beyond the rated life could
cause them to break on rare
occasions.
9. Never replace the lamp assembly or
any electronic components unless
the projector is unplugged.
10. Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
11. Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause
death if you should come into
contact with live parts. The only
user serviceable part is the lamp
which has its own removable cover.
Under no circumstances should you
ever undo or remove any other
covers. Refer servicing only to
suitably qualified professional
service personnel.
12. When the projector is under
operation, you may sense some
heated air and odor from its
ventilation grill. It is a normal
phenomenon and not a product
defect.
Important safety instructions 5
Safety Instructions (Continued)
13. Do not place this projector in any of the
following environments.
- Space that is poorly ventilated or confined.
Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled up.
- Locations where excessive humidity, dust,
or cigarette smoke may contaminate
optical components, shortening the
projector's life span and darkening the
image.
- Locations near fire alarms
- Locations with an ambient temperature
above 40°C / 104°F
- Locations where the altitudes are higher
than 3000 m (10000 feet).
14. Do not block the ventilation holes.
- Do not place this projector on a blanket,
bedding or any other soft surface.
- Do not cover this projector with a cloth or
any other item.
- Do not place inflammables near the
projector.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
15. Always place the projector on a level,
horizontal surface during operation.
- Do not use if tilted at an angle of more
than 10 degrees left to right, nor at angle
of more than 15 degrees front to back.
Using the projector when it is not fully
horizontal may cause a malfunction of, or
damage to, the lamp.
16. Do not stand the projector on end
vertically. Doing so may cause the
projector to fall over, causing injury or
resulting in damage to the projector.
3000 m
(10000 feet)
0 m
(0 feet)
Important safety instructions6
Safety Instructions (Continued)
17. Do not step on the projector or place
any objects upon it. Besides probable
physical damage to the projector, doing
so may result in accidents and possible
injury.
18. Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet, disconnect
it from the power supply's wall socket
and call BenQ to have the projector
serviced.
19. This product is capable of displaying
inverted images for ceiling mount
installation.
Use only BenQ's Ceiling Mount Kit for
mounting the projector and ensure it is
securely installed.
Ceiling mounting the projector
We want you to have a pleasant
experience using your BenQ projector,
so we need to bring this safety matter to
your attention to prevent possible
damage to person and property.
If you intend to mount your projector
on the ceiling, we strongly recommend
that you use a proper fitting BenQ
projector ceiling mount kit and that
you ensure it is securely and safely
installed.
If you use a non-BenQ brand projector
ceiling mount kit, there is a safety risk
that the projector may fall from the
ceiling due to an improper attachment
through the use of the wrong gauge or
length screws.
You can purchase a BenQ projector
ceiling mount kit from the place you
purchased your BenQ projector. BenQ
recommends that you also purchase a
separate Kensington lock compatible
security cable and attach it securely to
both the Kensington lock slot on the
projector and the base of the ceiling
mount bracket. This will perform the
secondary role of restraining the
projector should its attachment to the
mounting bracket become loose.
Introduction 7
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
Wall color correction allowing projection on surfaces of several predefined colors
Quick auto search speeding up the signal detecting process
Selectable password protected function
Up to 11 sets of picture modes providing multiple choices for different projection
purposes
3D color management allowing color adjustments to your liking
Detachable keypad on the projector to prevent stealing
Splash Screen lock to prevent unauthorized use
Selectable quick cooling function makes the projector cool in a shorter time
FAQ to troubleshoot operational problems with one quick button press
Presentation timer for a better control of time during presentations
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
High brightness projection lamp
Ability to display 16.7 million colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and Economic modes to reduce the power consumption
Built-in speaker provides mixed mono audio when an audio input is connected
Powerful AV function to provide high quality video image
Component HDTV compatibility (YP
bPr)
HDCP compatibility
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input source contrast/brightness settings, and is directly
proportional to projection distance.
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction8
Shipping contents
The projector is shipped with the cables required for connection to a PC or video
equipment. Carefully unpack and verify that you have all of the items shown below. If any of
these items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
*The warranty card and safety manual are only supplied in some specific regions. Please
consult your dealer for detailed information.
Optional accessories
Projector Remote control with batteries
Quick start guide User manual CD Soft cover Warranty card* Safety manual*
Power cord VGA cable
PUSH
(UK) (US)
(AU)
(KOREA)
(CHINA) (EU)
1. Spare lamp kit
2. Ceiling mount kit
3. Presentation Plus
4. RS232 cable
5. Soft carry case
Introduction 9
Projector exterior view
1. Lamp cover
2. Vent (heated air exhaust)
3. Projection lens
4. Quick-release button
5. External control panel
(See "Projector" on page 10
for details.)
6. Focus ring
7. Vent (cool air intake)
8. Front IR remote sensor
9. AC power cord inlet
10. Kensington anti-theft lock
slot
11. Rear adjuster foot
12. Ceiling mounting holes
13. Rear IR remote sensor
14. Video input socket
15. S-Video input socket
16. RGB signal output socket
17. RGB (PC)/Component
video (YPbPr/ YCbCr)
signal input socket
18. DVI input socket
19. Audio socket
20. 12VDC output terminal
Used to trigger external
devices such as an electric
screen or light control, etc.
Consult your dealer for how
to connect these devices.
21. USB socket
22. RS232 control port
23. Speaker grill
PUSH
4
3
2
1
5
6
7
8
Front/upper side
11
14 15 16
17 18
19
20 21
22
23
13
4
10
12
Rear/lower side
9
Introduction10
Controls and functions
Projector
1. Focus ring
Adjusts the focus of the projected image.
See "Fine-tuning the image clarity" on page
32 for details.
2. TEMPerature warning light
Lights up red if the projector's temperature
becomes too high. See "Indicators" on page
59 for details.
3. POWER indicator light
Lights up or flashes when the projector is
under operation. See "Indicators" on page
59 for details.
4. Power
Toggles the projector on or off.
See "Starting up the projector" on page 26
and "Shutting down the projector" on page
45 for details.
5. MENU/EXIT
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings. See "Using
the menus" on page 27 for details.
6. Left/
Starts the FAQ function. See "Utilizing FAQ
function" on page 42 for details.
7. BLANK
Used to hide the screen image. See "Hiding
the image" on page 41 for details.
8. LAMP indicator light
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem. See "Indicators" on page 59 for
details.
9. Keystone/Arrow buttons ( / Up, /
Down)
Manually corrects distorted images
resulting from an angled projection. See
"Correcting keystone" on page 33 for
details.
10. AUTO
Automatically determines the best picture
timings for the displayed image. See "Auto-
adjusting the image" on page 32 for details.
11. Right/
Activates panel key lock. See "Panel Key
Lock" on page 50 for details.
When the On-Screen Display (OSD) menu
is activated, the #6, #9, and #11 buttons are
used as directional arrows to select the
desired menu items and to make
adjustments. See "Using the menus" on
page 27 for details.
12. SOURCE
Displays the source selection bar. See
"Switching input signal" on page 31 for
details.
13. Mode/enter
Selects an available picture setup mode. See
"Selecting a picture mode" on page 35 for
details.
Enacts the selected On-Screen Display
(OSD) menu item. See "Using the menus"
on page 27 for details.
1
4
5
6
7
9
10
11
12
3
2
8
8
13
I
I
Introduction 11
Remote control
1. Power
Toggles the projector on or off.
See "Starting up the projector" on page 26
and "Shutting down the projector" on page
45 for details.
2. ASPECT
Selects the display aspect ratio. See
"Selecting the aspect ratio" on page 34 for
details.
3. CAPTURE
Captures the projected picture and save it
as your startup screen. See "Creating your
own startup screen" on page 43 for details.
4. Keystone/Arrow buttons ( / Up, /
Down)
Manually corrects distorted images
resulting from an angled projection. See
"Correcting keystone" on page 33 for
details.
5. MENU/EXIT
Tur ns on the On-Screen D is play (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings. See "Using
the menus" on page 27 for details.
6. Left/
Starts the FAQ function. See "Utilizing
FAQ function" on page 42 for details.
7. BLANK
Used to hide the screen image. See "Hiding
the image" on page 41 for details.
8. ENTER
Enacts the selected On-Screen Display
(OSD) menu item. See "Using the menus"
on page 27 for details.
9. TIMER ON/SHOW
Activates or displays an on-screen timer
based on your own timer setting. See
"Setting the presentation timer" on page 39
for details.
10. BRIGHTNESS
Adjusts brightness. See "Adjusting
Brightness" on page 36 for details.
11. CONTRAST
Adjusts contrast. See "Adjusting Contrast"
on page 36 for details.
12. TIMER SETUP
Enters presentation timer setting directly.
See "Setting the presentation timer" on
page 39 for details.
2
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
4
20
21
22
I
I
Introduction12
13. Indicator light
Flashes or lights red when any key on the
remote control is pressed.
14. MODE
Depending upon which input signal is
selected, selects an available picture mode.
See "Selecting a picture mode" on page 35
for details.
15. FREEZE
Freezes the projected image. See "Freezing
the image" on page 41 for details.
16. MUTE
Toggles projector audio between on and
off.
17. AUTO
Automatically determines the best picture
timings for the displayed image. See "Auto-
adjusting the image" on page 32 for details.
18. Right/
Locks the buttons on the projector. See
"Locking control keys" on page 42 for
details.
When the On-Screen Display (OSD) menu
is activated, the #4, #6 and #18 buttons are
used as directional arrows to select the
desired menu items and to make
adjustments. See "Using the menus" on
page 27 for details.
19. SOURCE
Displays the source selection bar. See
"Switching input signal" on page 31 for
details.
20. LASER
Emits visible laser pointer light for
presentation purposes. See "Operating the
LASER pointer" on the right for details.
21. PAGE
/
Operate your display software program (on
a connected PC) which responds to page
up/down commands (like Microsoft
PowerPoint). See "Remote paging
operations" on page 40 for details.
22. D. ZOOM (+, -)
Magnifies or reduces the projected image
size. See "Magnifying and searching for
details on the projected picture" on page 33
for details.
Operating the LASER pointer
The LASER Pointer is a
presentation aid for
professionals. It emits red
colored light when you press it
and the indicator lights up red.
The laser beam is visible. It is
necessary to press and hold
LASER for continuous output.
Do not look into the laser light window or
shine the laser light beam on yourself or
others. See the warning messages on the
back of the remote control and the enclosed
''User Information'' prior to using it.
The laser pointer is not a toy. Parents should be
mindful of the dangers of laser energy and keep
this remote control out of the reach of children.
Introduction 13
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the back of the projector.
The remote control must be held at an angle within 30 degrees perpendicular to the
projector's IR remote control sensors to function correctly. The distance between the remote
control and the sensors should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensors on the
projector that might obstruct the infra-red beam.
Replacing the remote control batteries
1. To open the battery cover, turn the remote control over to view its back, push on the
finger grip on the cover and slide it up in the direction of the arrow as illustrated. The
cover will slide off.
2. Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
3. Refit the cover by aligning it with the base and sliding it back down into position. Stop
when it clicks into place.
Avoid leaving the remote control and batteries in an excessive heat or humid environment like
the kitchen, bathroom, sauna, sunroom or in a closed car.
Replace only with the same or equivalent type recommended by the battery manufacturer.
Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
Never throw the batteries into a fire. There may be danger of an explosion.
If the batteries are dead or if you will not be using the remote control for an extended period of
time, remove the batteries to avoid damage to the remote control from possible battery
leakage.
PUSH
Operating the projector from the
front
A
p
p
r
o
x
.
1
5
°
A
p
p
r
o
x
.
1
5
°
Operating the projector from the
rear
Positioning your projector14
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation locations:
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
1. Front Table
Select this location with the projector placed near the
floor in front of the screen. This is the most common
way to position the projector for quick setup and
portability.
2. Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the screen.
Purchase the BenQ Projector Ceiling Mounting Kit
from your dealer to mount your projector on the
ceiling.
Set Front Ceiling in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector
on.
3. Rear Table
Select this location with the projector placed near the
floor behind the screen.
Note that a special rear projection screen is required.
Set Rear Table in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector
on.
4. Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
BenQ Projector Ceiling Mounting Kit are required for
this installation location.
Set Rear Ceiling in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector on.
Positioning your projector 15
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting, and the video format
each factors in the projected image size.
4:3 is the native aspect ratio of this projector. To be able to project a complete 16:9
(widescreen) aspect ratio image, the projector can resize and scale a widescreen image to the
projector's native aspect width. This will result in a proportionally smaller height equivalent
to 75% of the projector's native aspect height.
Thus, a 16:9 aspect image will not utilize 25% of the height of a 4:3 aspect image displayed
by this projector. This will be seen as darkened (unlit) bars along the top and bottom
(vertical 12.5% height respectively) of the 4:3 projection display area whenever displaying a
scaled 16:9 aspect image in the vertical center of the 4:3 projection display area.
When determining the position of your projector, you should consider its intended use and
input signal aspect ratios. All inputs (other than composite Video being fed a 16:9 aspect
signal) will display in a 4:3 aspect ratio (and will require an additional 33% display height
than that of the scaled 16:9 aspect image projection area).
IMPORTANT: Do not select a permanent projector position based upon a 16:9 projection if you
will ever need to select an input (other than composite Video being fed a 16:9 aspect signal).
The projector should always be placed horizontally level (like flat on a table), and positioned
directly perpendicular (90° right-angle square) to the horizontal center of the screen. This
prevents image distortion caused by angled projections (or projecting onto angled surfaces).
The modern digital projector does not project directly forward (like older style reel-to-reel
film projectors did). Instead, digital projectors are designed to project at a slightly upward
angle above the horizontal plane of the projector. This is so that they can be readily placed
on a table and will project forward and upwards onto a screen positioned so that the bottom
edge of the screen is above the level of the table (and everyone in the room can see the
screen).
If the projector is mounted on a ceiling, it must be mounted upside-down so that it projects
at a slightly downward angle.
You can see from the diagram on page 17, that this type of projection causes the bottom edge
of the projected image to be vertically offset from the horizontal plane of the projector.
When ceiling mounted, this refers to the top edge of the projected image.
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for
both the projected image size and the vertical offset dimension, which are directly
proportional to the projection distance.
BenQ has provided a table of 4:3-aspect-ratio screen sizes to assist you in determining the
ideal location for your projector. There are two dimensions to consider, the perpendicular
horizontal distance from the center of the screen (projection distance), and the vertical
offset height of the projector from the horizontal edge of the screen (offset).
4:3 aspect image in a 4:3 aspect display area
16:9 aspect image scaled to a 4:3 aspect
display area
Positioning your projector16
How to determine the position of the projector for a given
screen size
1. Select your screen size.
2. Refer to the table and find the closest match to your screen size in the left columns
labelled "4:3 screen diagonal". Using this value, look across this row to the right to find
the corresponding average distance from screen value in the column labelled
"Recommended projection distance from screen in mm". This is the projection
distance.
3. On that same row, look across to the right column and make note of the Vertical offset
value. This will determine the final vertical offset placement of the projector in
relation to the edge of the screen.
4. The recommended position for the projector is aligned perpendicular to the
horizontal center of the screen, at the distance from the screen determined in step 2
above, and offset by the value determined in step 3 above.
For example, if you are using a 120 inch screen, the recommended projection distance is
1622 mm and with a vertical offset of 183 mm.
If you place the projector in a different position (to that recommended), you will have to tilt
it down or up to center the image on the screen. In these situations, some image distortion
will occur. Use the Keystone function to correct the distortion. See "Correcting keystone" on
page 33 for details.
How to determine the recommended screen size for a
given distance
This method can be used for situations where you have purchased this projector and would
like to know what screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room.
1. Measure the distance between the projector and where you want to position the
screen. This is the projection distance.
2. Refer to the table and find the closest match to your measurement in the average
distance from screen column labelled "Recommended projection distance from screen
in mm".
3. Using this value, look across that row to the left to find the corresponding screen
diagonal listed in that row. That is the projected image size of the projector at that
projection distance.
4. On that same row, look across to the right column and make note of the Vertical offset
value. This will determine the final placement of the screen in relation to the
horizontal plane of the projector.
For example, if your measured projection distance was 2 m (2000 mm), the closest match in
the "Recommended projection distance from screen in mm" column is 1946 mm. Looking
across this row shows that a 12' (144") screen is required. If you can only obtain metric sized
screens, the screen size is 3658 mm diagonally.
Positioning your projector 17
There is 3% tolerance among these numbers due to optical component variations. BenQ
recommends that if you intend to permanently install the projector, you should physically test
the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
4:3 screen diagonal Recommended projection distance
from screen in mm
Vertical offset in mm
Feet Inches mm
5 60 1524 811 91
6 72 1829 973 110
2000 1064 120
7 84 2134 1135 128
8 96 2438 1297 146
2500 1330 150
9 108 2743 1459 165
3000 1596 180
10 120 3048 1622 183
3500 1862 210
12 144 3658 1946 219
4000 2128 240
15 180 4572 2432 274
5000 2660 300
18 216 5486 2919 329
6000 3192 360
25 300 7620 4054 457
4:3 Screen Diagonal
Projection distance
Center of lens
Screen
Offset
Connection18
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 8). They are commercially available from electronics stores.
Connecting a computer or monitor
Connecting a computer
The projector provides a VGA and DVI input sockets that allow you to connect it to both
IB compatibles and Macintosh® computers. A Mac adapter (an optional accessory) is
needed if you are connecting legacy version Macintosh computers.
Additionally, you can also connect the projector to a computer via the USB cable so you can
perform paging operations of the application on the PC or notebook.
To connect the projector to a notebook or desktop computer (either through a
VGA cable or VGA to DVI-A cable):
With a VGA cable: With a VGA to DVI-A cable:
1. Take the supplied VGA cable and
connect one end to the D-Sub
output socket of the computer.
2. Connect the other end of the VGA
cable to the D-SUB/COMP. IN
signal input socket on the projector.
1. Take a VGA to DVI-A cable and
connect the VGA end to the D-Sub
output socket of the computer.
2. Connect the DVI end of the VGA to
DVI-A cable to the DVI signal input
socket on the projector.
3. If you wish to use the remote paging function, take a USB cable and connect the
larger end to the USB port of the computer, and the smaller end to the USB socket
on the projector. See "Remote paging operations" on page 40 for details.
4. If you wish to make use of the projector (mixed mono) speaker in your
presentations, take a suitable audio cable and connect one end of the cable to the
audio output socket of the computer, and the other end to the AUDIO socket of
the projector.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus. See "Audio Settings" on page 51 for details.
Connection 19
The final connection path should be like that shown in the following diagram:
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
notebook or
desktop computer
or
iii
iii
i. VGA cable
ii. VGA to DVI-A cable
iii.Audio cable
iv.USB cable
iv
Connection20
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the D-SUB OUT signal output socket on the projector to an external monitor
with a VGA or VGA to DVI-A cable by following the instructions below.
To connect the projector to a monitor (either through a VGA cable or VGA to
DVI-A cable):
The final connection path should be like that shown in the following diagram:
With a VGA cable: With a VGA to DVI-A cable:
Note: Your monitor must be equipped with
a DVI input socket.
1. Connect the projector to a computer as described in "Connecting a computer" on
page 18.
The D-SUB output only works when an appropriate D-SUB input is made to the
projector. Be sure the projector is connecting with the computer using the D-SUB/
COMP. IN socket, not the DVI socket.
2. Take a suitable VGA cable (only one
supplied) and connect one end of
the cable to the D-Sub input socket
of the video monitor.
3. Connect the other end of the cable
to the D-SUB OUT socket on the
projector.
2. Take a VGA to DVI-A cable and
connect the DVI end of the cable to
the DVI input socket of the video
monitor.
3. Connect the VGA end of the cable to
the D-SUB OUT socket on the
projector.
notebook or desktop
computer
(VGA)
(DVI)
iii
iii
i. VGA to DVI-A cable
ii. VGA cable
iii.VGA cable
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

BenQ mp 771 User manual

Category
Data projectors
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI