Cisco Network Convergence System 5000 Series Installation guide

Network Convergence System 5000 Series
Cisco
Brand
Cisco
Model
Network Convergence System 5000 Series
Type
Installation guide

This manual is also suitable for

Hardware Installation Guide for Cisco NCS 5000 Series Routers
First Published: 2015-12-23
Last Modified: 2019-01-31
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com
go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any
other company. (1721R)
©2015–2019 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface vii
PREFACE
Changes to This Document vii
Communications, Services, and Additional Information vii
Overview 1
CHAPTER 1
Overview 1
Cisco NCS 5001 1
Cisco NCS 5002 3
Cisco NCS 5011 6
Cisco NCS 5064 9
Safety Guidelines 13
CHAPTER 2
Cisco NCS 5000 Safety Guidelines 13
Prepare to Install Cisco NCS 5000 15
CHAPTER 3
Installation Options with Racks and Cabinets 15
Airflow Direction 15
Chassis Weight 15
Required Equipment 16
Unpack and Inspect the New Router 16
Installing the NCS 5000 Router 19
CHAPTER 4
Installation Guidelines 19
Installing Cisco NCS 5000 20
Installing Cisco NCS 5001 20
Installing Cisco NCS 5002 22
Hardware Installation Guide for Cisco NCS 5000 Series Routers
iii
Installing Cisco NCS 5011 25
Installing Cisco NCS 5064 on a 2-post Rack 27
Installing Cisco NCS 5064 in a 4-post Rack 28
Grounding Cisco NCS 5000 31
Starting Cisco NCS 5000 33
Replacing NCS 5000 Router Components 35
CHAPTER 5
Replacing a Fan Module 35
Replacing a 1 (RU) Fan Module 36
Replacing a 2 (RU) Fan Module 37
(Only for NCS 5064) Replacing a 2 (RU) Fan Module 38
Replacing an AC Power Supply 39
Replacing a DC Power Supply 41
Replacing the Air Filter for Port Side Intake 42
Replacing Air Filter for Port Side Exhaust 43
(Only for NCS 5064) Replacing the Air Filter for Port Side Intake 45
(Only for NCS 5064) Replacing Air Filter for Port Side Exhaust 46
Accessory Kits 49
APPENDIX A
Accessory Kit Contents 49
Cisco NCS 5001 Router Accessory Kit 49
Cisco NCS 5002 Router Accessory Kit 49
Cisco NCS 5011 Router Accessory Kit 50
Cisco NCS 5064 Router Accessory Kit 50
Cabinet and Rack Installation 53
APPENDIX B
Cabinet and Rack Requirements 53
General Requirements for Cabins and Racks 53
Requirements Specific to Perforated Cabinets 54
Cable Management Guidelines 54
Technical Specifications 55
APPENDIX C
Router Specifications 55
Environment Specification 56
Hardware Installation Guide for Cisco NCS 5000 Series Routers
iv
Contents
Power Specifications 57
Specifications for the Cisco NCS 5001 Power Supply 57
Specifications for the Cisco NCS 5002 Power Supply 58
Specifications for the Cisco NCS 5011 Power Supply 59
Specifications for the Cisco NCS 5064 Power Supply 60
Cable and Port Specification 63
APPENDIX D
Console Port 63
Supported Power Cords and Plugs 63
Jumper Power Cord 67
LEDs 69
APPENDIX E
Chassis and Module LEDs for the Cisco NCS 5000 Series Routers 69
Chassis and Module LED Descriptions 69
Conditions Indicated by the Power Supply LEDs 70
Troubleshooting Hardware Components 71
APPENDIX F
Overview 71
Router Hardware Best Practices 71
Installation Best Practices 71
Initialization Best Practice 72
Router Operation Best Practices 72
Power Supply Conditions 72
Hardware Installation Guide for Cisco NCS 5000 Series Routers
v
Contents
Hardware Installation Guide for Cisco NCS 5000 Series Routers
vi
Contents
Preface
•Changes to This Document, on page vii
•Communications, Services, and Additional Information, on page vii
Changes to This Document
This table lists the technical changes made to this document since it was first released.
Table 1: Changes to This Document
SummaryDate
Initial release of this document for the 6.0 release.December 2015
Added information about NCS 5011.April 2016
Republished with documentation updates for Release
6.1.2 features.
November 2016
Republished with documentation updates for Release
6.2.1 features.
February 2017
Added information about NCS 5064.January 2019
Communications, Services, and Additional Information
• To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager.
• To get the business impact you’re looking for with the technologies that matter, visit Cisco Services.
• To submit a service request, visit Cisco Support.
• To discover and browse secure, validated enterprise-class apps, products, solutions and services, visit
Cisco Marketplace.
• To obtain general networking, training, and certification titles, visit Cisco Press.
• To find warranty information for a specific product or product family, access Cisco Warranty Finder.
Hardware Installation Guide for Cisco NCS 5000 Series Routers
vii
Cisco Bug Search Tool
Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking system
that maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST provides
you with detailed defect information about your products and software.
Hardware Installation Guide for Cisco NCS 5000 Series Routers
viii
Preface
Preface
CHAPTER 1
Overview
This chapter provides an overview of the Cisco 5000 Series routers.
The Network Convergence System 5000 Series offers a high-density, small-form-factor MPLS aggregation
router for metro aggregation. It is designed to economically scale large enterprise, over-the-top (OTT), and
service provider Data Center networking architectures.
•Overview, on page 1
•Cisco NCS 5001, on page 1
•Cisco NCS 5002, on page 3
•Cisco NCS 5011, on page 6
•Cisco NCS 5064, on page 9
Overview
This chapter provides an overview of the Cisco 5000 Series routers.
The Network Convergence System 5000 Series offers a high-density, small-form-factor MPLS aggregation
router for metro aggregation. It is designed to economically scale large enterprise, over-the-top (OTT), and
service provider Data Center networking architectures.
Cisco NCS 5001
Cisco NCS 5001 Overview
The Cisco NCS 5001 router is an extension to Cisco's routing platform portfolio enabling Service Providers
and MPLS enabled data center architectures to offer elastic networks with improved business agility and
simplified operations to deliver high-bandwidth mobile, video, and cloud services.
It can also operate as an extension shelf of Cisco ASR 9000 Series Aggregation Services Routers using
Network Virtualization (nV) technology, consolidating multiple layers in the network and dramatically reducing
operational costs.
The Cisco NCS 5001 router is a small form factor dense GE/10GE aggregation systems. Powered by industry
leading routing operation system, IOS-XR, the system also offers rich functions such as third party application
hosting, machine-to-machine interface, telemetry and flexible package delivery.
Hardware Installation Guide for Cisco NCS 5000 Series Routers
1
Figure 1: Cisco NCS 5001 Router - Back (Fan Side) View
Figure 2: Cisco NCS 5001 Router - Front (Port Side) View
Ports
Cisco NCS 5001 router consists of the following ports:
• 40 x One GE/10GE SFP+ ports
• 16 x Regular 10G SFP+ Ports
• 24 x DWDM and ZR Capable 10G SFP+ Ports (Purple in color)
• 4 x 100G QSFP28 ports (Light Green in color)
Features
The Cisco NCS 5001 router has the following features:
• Two 1+1 redundant, hot-swappable power supplies, which provide port side intake or exhaust for cooling
• Two 1+1 redundant, hot-swappable fan modules, which provide port side intake or exhaust for cooling
• A management and console interface are on the port (front) side of the router whereas the USB interface
on the fan (back) side of the router.
Power Supply
The Cisco NCS 5001 chassis has slots for two 1+1 redundant power supplies. Power supply options need to
be configured with the base chassis. A minimum of one power supply is required for normal operation. The
following table lists the power supplies that are configurable with the Cisco NCS 5001 router.
Hardware Installation Guide for Cisco NCS 5000 Series Routers
2
Overview
Cisco NCS 5001
Table 2: Power Supplies for the Cisco NCS 5001 router
Power SupplyPart Number
Cisco NCS 5000 Power DC 930W Front to Back AirflowNC5K-PDC-930W-FR
Cisco NCS 5000 Power DC 930W Front to Back Airflow, spareNC5K-PDC-930W-FR=
Cisco NCS 5000 Power DC 930W Back to Front AirflowNC5K-PDC-930W-BK
Cisco NCS 5000 Power DC 930W Back to Front Airflow, spareNC5K-PDC-930W-BK=
Cisco NCS 5000 Series Router Power AC 650W Front to Back AirflowNC5K-PAC-650W-FR
Cisco NCS 5000 Series Router Power AC 650W Front to Back
Airflow, spare
NC5K-PAC-650W-FR=
Cisco NCS 5000 Series Router Power AC 650W Back to Front AirflowNC5K-PAC-650W-BK
Cisco NCS 5000 Series Router Power AC 650W Back to Front
Airflow, spare
NC5K-PAC-650W-BK=
Fan Modules
The Cisco NCS 5001 chassis has slots for two 1+1 redundant fan modules. The fan modules are hot-swappable.
Fan modules operate in an 1+1 redundancy mode. Fan options need to be configured with the base chassis.
The Cisco NCS 5001 system supports both forward and reverse airflow. The system can work with a single
fan failure. More than one fan failure leads to system shutdown. The following table lists the fan modules
that are configurable with the Cisco NCS 5001 router.
Table 3: Fan Modules for the Cisco NCS 5001 router
Fan ModulePart Number
Cisco NCS 5001 Router Fan Front to Back AirflowNCS-5001-FN-FR
Cisco NCS 5001 Router Fan Front to Back Airflow, spareNCS-5001-FN-FR=
Cisco NCS 5001 Router Fan Back to Front AirflowNCS-5001-FN-BK
Cisco NCS 5001 Router Fan Back to Front Airflow, spareNCS-5001-FN-BK =
Cisco NCS 5002
Cisco NCS 5002
The Cisco NCS 5002 router is also an extension to Cisco's routing platform portfolio enabling Service Providers
and MPLS enabled data center architectures to offer elastic networks with improved business agility and
simplified operations to deliver high-bandwidth mobile, video, and cloud services.
It can also operate as an extension shelf of Cisco ASR 9000 Series Aggregation Services Routers using
Network Virtualization (nV) technology, consolidating multiple layers in the network and dramatically reducing
operational costs.
Hardware Installation Guide for Cisco NCS 5000 Series Routers
3
Overview
Cisco NCS 5002
The Cisco NCS 5002 router is a small form factor dense GE/10GE aggregation systems in 2RU form factor.
Powered by industry leading routing operation system, IOS-XR, the system also offers rich functions such as
third party application hosting, machine-to-machine interface, telemetry and flexible package delivery.
Figure 3: Cisco NCS 5002 - Back (Fan Side) View
Figure 4: Cisco NCS 5002 - Front (Port Side) View
Ports
Cisco NCS 5002 router consists of the following ports:
• 80 x One GE/10GE SFP+ ports
• 40 x Regular 10G SFP+ Ports, on baseboard
• 40 x DWDM and ZR Capable 10G SFP+ Ports, on mezzanine (Cisco Metallic Grey in color)
• 4 x 100G QSFP28 ports (Light Green in color)
Features
The Cisco NCS 5002 router has the following features:
• Two 1+1 redundant, hot-swappable power supplies, which provide port side intake or exhaust for cooling
• Two 1+1 redundant, hot-swappable fan modules, which provide port side intake or exhaust for cooling
• A management, console, and the USB interface on the port (front) side of the router
Hardware Installation Guide for Cisco NCS 5000 Series Routers
4
Overview
Cisco NCS 5002
Power Supply
The Cisco NCS 5002 chassis has slots for two 1+1 redundant power supplies. Power supply options need to
be configured with the base chassis. A minimum of one power supply is required for normal operation. The
following table lists the power supplies that are configurable with the Cisco NCS 5002 router.
Table 4: Power Supplies for the Cisco NCS 5002 router
Power SupplyPart Number
Cisco NCS 5000 Power DC 930W Front to Back AirflowNC5K-PDC-930W-FR
Cisco NCS 5000 Power DC 930W Front to Back Airflow, spareNC5K-PDC-930W-FR=
Cisco NCS 5000 Power DC 930W Back to Front AirflowNC5K-PDC-930W-BK
Cisco NCS 5000 Power DC 930W Back to Front Airflow, spareNC5K-PDC-930W-BK=
Cisco NCS 5000 Series Router Power AC 650W Front to Back
Airflow
NC5K-PAC-650W-FR
Cisco NCS 5000 Series Router Power AC 650W Front to Back
Airflow, spare
NC5K-PAC-650W-FR=
Cisco NCS 5000 Series Router Power AC 650W Back to Front
Airflow
NC5K-PAC-650W-BK
Cisco NCS 5000 Series Router Power AC 650W Back to Front
Airflow, spare
NC5K-PAC-650W-BK=
Fan Modules
The Cisco NCS 5002 chassis has slots for two 1+1 redundant fan modules. The fan modules are hot-swappable.
Fan modules operate in an 1+1 redundancy mode. Fan options need to be configured with the base chassis.
The Cisco NCS 5002 system supports both forward and reverse airflow. The system can work with a single
fan failure. More than one fan failure leads to system shutdown. The following table lists the fan modules
that are configurable with the Cisco NCS 5002 router.
Table 5: Fan Modules for the Cisco NCS 5002 router
Fan ModulePart Number
Cisco NCS 5002 Router Fan Front
to Back Airflow
NCS-5002-FN-FR
Cisco NCS 5002 Router Fan Front
to Back Airflow, spare
NCS-5002-FN-FR=
Cisco NCS 5002 Router Fan Back
to Front Airflow
NCS-5002-FN-BK
Cisco NCS 5002 Router Fan Back
to Front Airflow, spare
NCS-5002-FN-BK=
Hardware Installation Guide for Cisco NCS 5000 Series Routers
5
Overview
Cisco NCS 5002
Cisco NCS 5011
Cisco NCS 5011
The Cisco NCS 5011 router is also an extension to Cisco's routing platform portfolio enabling Service Providers
and MPLS enabled data center architectures to offer elastic networks with improved business agility and
simplified operations to deliver high-bandwidth mobile, video, and cloud services.
The Cisco NCS 5011 router consists of 32 QSFP+/QSFP28 ports. The NCS 5011 system supports 10GE,
25GE, 40GE, 50GE, and 100GE.
The Cisco NCS 5011 system extends 4x10G, 4x25G, and 2x50G breakout support for Copper Optics.
Configure Breakout
Log into the router in the config mode, and type the following command (in this example, the breakout optics
is inserted in port 0):
RP/0/RP0/CPU0:router(config)# controller optics 0/0/0/0 breakout 4x10
RP/0/RP0/CPU0:router(config)# controller optics 0/0/0/0 breakout 4x25
RP/0/RP0/CPU0:router(config)# controller optics 0/0/0/0 breakout 2x50
• The broken out interfaces are named as follows:
• tenGigE 0/0/0/0/0, tenGigE 0/0/0/0/1, tenGigE 0/0/0/0/2, and tenGigE 0/0/0/0/3
•twentyFiveGigE 0/0/0/0/0, twentyFiveGigE 0/0/0/0/1, twentyFiveGigE 0/0/0/0/2, and twentyFiveGigE
0/0/0/0/3
• FiftyGigE 0/0/0/0/0, FiftyGigE 0/0/0/0/1
• The above commands fail if the optics inserted do not support breakout. Only copper optics are currently
supported.
• The commands succeed if there are no optics inserted, and the breakout is executed whenever optics are
inserted at a later stage.
Note
Hardware Installation Guide for Cisco NCS 5000 Series Routers
6
Overview
Cisco NCS 5011
Figure 5: Cisco NCS 5011 - Back (Fan Side) View
Figure 6: Cisco NCS 5011 - Front (Port Side) View
Ports
Cisco NCS 5011 router consists of the following ports:
• 2 x 10GE SFP + ports
• 32 x 100G QSFP28-100 ports
Features
The Cisco NCS 5011 router has the following features:
• Two 1+1 redundant, hot-swappable power supplies, which provide port side intake or exhaust for cooling
• Four 3+1 redundant, hot-swappable fan modules, which provide port side intake or exhaust for cooling
• A management, console, and the USB interface on fan side of the router
Hardware Installation Guide for Cisco NCS 5000 Series Routers
7
Overview
Cisco NCS 5011
Power Supply
The Cisco NCS 5011 chassis has slots for two 1+1 redundant power supplies. Power supply options need to
be configured with the base chassis. A minimum of one power supply is required for normal operation. The
following table lists the power supplies that are configurable with the Cisco NCS 5011 router.
Table 6: Power Supplies for the Cisco NCS 5011 router
Power SupplyPart Number
Cisco NCS 5000 Power DC 930W Front to Back AirflowNC5K-PDC-930W-FR
Cisco NCS 5000 Power DC 930W Front to Back Airflow, spareNC5K-PDC-930W-FR=
Cisco NCS 5000 Power DC 930W Back to Front AirflowNC5K-PDC-930W-BK
Cisco NCS 5000 Power DC 930W Back to Front Airflow, spareNC5K-PDC-930W-BK=
Cisco NCS 5000 Series Router Power AC 650W Front to Back
Airflow
NC5K-PAC-650W-FR
Cisco NCS 5000 Series Router Power AC 650W Front to Back
Airflow, spare
NC5K-PAC-650W-FR=
Cisco NCS 5000 Series Router Power AC 650W Back to Front
Airflow
NC5K-PAC-650W-BK
Cisco NCS 5000 Series Router Power AC 650W Back to Front
Airflow, spare
NC5K-PAC-650W-BK=
Fan Modules
The Cisco NCS 5011 chassis has slots for four 3+1 redundant fan modules. The fan modules are hot-swappable.
Fan options need to be configured with the base chassis. The Cisco NCS 5011 system supports both forward
and reverse airflow. The system can work with a single fan failure. More than one fan failure leads to system
shutdown. The following table lists the fan modules that are configurable with the Cisco NCS 5011 router.
Table 7: Fan Modules for the Cisco NCS 5011 router
Fan ModulePart Number
Cisco NCS 5011 Router Fan Front
to Back Airflow
NCS-5011-FN-FR
Cisco NCS 5011 Router Fan Front
to Back Airflow, spare
NCS-5011-FN-FR=
Cisco NCS 5011 Router Fan Back
to Front Airflow
NCS-5011-FN-BK
Cisco NCS 5011 Router Fan Back
to Front Airflow, spare
NCS-5011-FN-BK=
Hardware Installation Guide for Cisco NCS 5000 Series Routers
8
Overview
Cisco NCS 5011
Cisco NCS 5064
The Cisco NCS 5064 router, which is also an extension to Cisco's routing platform portfolio enabling Service
Providers and MPLS enabled data center architectures to offer elastic networks with improved business agility
and simplified operations to deliver high-bandwidth mobile, video, and cloud services.
The Cisco NCS 5064 router is a small form factor dense 100GE aggregation systems in 2RU form factor.
Powered by industry leading routing operation system, IOS-XR, the system also offers rich functions such as
third party application hosting, machine-to-machine interface, telemetry and flexible package delivery.
Figure 7: Cisco NCS 5064 - Back (Fan Side) View
Figure 8: Cisco NCS 5604 - Front (Port Side) View
Hardware Installation Guide for Cisco NCS 5000 Series Routers
9
Overview
Cisco NCS 5064
Ports
Figure 9: Cisco NCS 5604 Port Label
• 64 QSFP28 ports with the capability of operating at 100G and 40G rates.
• Ports 0-15 also support dynamic breakout with these combinations: 4x10G, 4x25G, and 2x50G.
• Ports 48-63 may also support MACsec in a future release.
• 2 x 10GE SFP+ ports (although physically present, these are not supported by IOS-XR).
Configure Breakout
Log into the router in the config mode, and type the following command (in this example, the breakout optics
is inserted in port 0):
RP/0/RP0/CPU0:router(config)# controller optics 0/0/0/0 breakout 4x10
RP/0/RP0/CPU0:router(config)# controller optics 0/0/0/0 breakout 4x25
RP/0/RP0/CPU0:router(config)# controller optics 0/0/0/0 breakout 2x50
• The broken out QSFP interface will be named as following, depending on the break out mode:
• 4x10G: TenGigE 0/0/0/0/0, TenGigE 0/0/0/0/1, TenGigE 0/0/0/0/2, and TenGigE 0/0/0/0/3
• 4x25G: TwentyFiveGigE 0/0/0/0/0, TwentyFiveGigE 0/0/0/0/1, TwentyFiveGigE 0/0/0/0/2, and
TwentyFiveGigE 0/0/0/0/3
• 2x50G: FiftyGigE 0/0/0/0/0, FiftyGigE 0/0/0/0/1
• The above commands fail if the optics inserted do not support breakout.
• The commands succeed if there are no optics inserted, and the breakout is executed whenever optics are
inserted at a later stage.
• For 4x10 breakout, copper and non-copper optics are also supported.
For 4x10 breakout, the supported optics type are : 40G SR4, 40G LR, 40G AOC, 40G PSM, 40G AC
(active copper), and 40G CR4 (passive copper).
Note
Features
The Cisco NCS 5064 router has the following features:
Hardware Installation Guide for Cisco NCS 5000 Series Routers
10
Overview
Cisco NCS 5064
• Two hot-swappable power supply (PSUs) that support 1+1 redundancy under most conditions. Only
when the 930W DC supplies (NC5K-PDC-930W-FR and NC5K-PDC-930W-BK) are used, both the
PSUs must be inserted and operational in a non-redundant 2+0 mode.
• Different power supply units (PSUs) are available for different air flow configurations.
• Three hot-swappable fan modules that provide port side intake or port side exhaust cooling in 2+1
redundancy mode.
• A management, console, and the USB interface on fan side of the router.
Power Supply
The Cisco NCS 5064 chassis has slots for two 1+1 redundant power supplies. Power supply options need to
be configured with the base chassis. A minimum of one power supply is required for normal operation.
When 930W DC power supply (NC5K-PDC-930W-BK or NC5K-PDC-930W-FR) is used, redundancy is not
supported.
Caution
The following table lists the power supplies that are configurable with the Cisco NCS 5064 router.
Table 8: Power Supplies for the Cisco NCS 5064 router and Redundancy Support Matrix
2+0
Non-Redundant
Mode
1+1
Redundant
Mode
1+0
Non-Redundant
Mode
ColorPower SupplyPart Number
YesNoNoRedCisco NCS
5000 Power DC
930W Front to
Back Airflow
NC5K-PDC-930W-FR
YesNoNoBlueCisco NCS
5000 Power DC
930W Back to
Front Airflow
NC5K-PDC-930W-BK
NoYesYesRedCisco NCS
5000 Power AC
1200W Front to
Back Airflow
NC5K-PAC-1200W-FR
NoYesYesBlueCisco NCS
5000 Series
Router Power
AC 1200W
NC55-1200W-ACFW
NoYesYesWhiteCisco NCS
5000 Power
HVAC/DC
1200W
Bi-direcitonal
Airflow
NC5K-PUV-1200W
Hardware Installation Guide for Cisco NCS 5000 Series Routers
11
Overview
Cisco NCS 5064
Fan Modules
The Cisco NCS 5064 chassis has slots for three 2+1 redundant fan modules. The fan modules are hot-swappable.
Fan options need to be configured with the base chassis. The Cisco NCS 5064 system supports both forward
and reverse airflow. The system can work with a single fan failure. More than one fan failure leads to system
shutdown. The following table lists the fan modules that are configurable with the Cisco NCS 5064 router.
To replace the fan module, see the (Only for NCS 5064) Replacing a 2 (RU) Fan Module, on page 38 procedure.
Table 9: Fan Modules for the Cisco NCS 5064 router
ColorFan ModulePart Number
RedCisco NCS 5064 Router Fan Front to Back AirflowNCS-5064-FN-FR
BlueCisco NCS 5064 Router Fan Back to Front AirflowNCS-5064-FN-BK
System Air flow
Power supplies and fan modules must maintain the same air flow direction. The airflow direction can be
identified based on the PID description and the handle color of both power supplies and fan modules.
Note, however, that the NC5K-PUV-1200W power supply can operate in both (front to back and back to
front) air flow directions. When this power supply is used, the Cisco IOS-XR software automatically configures
the PSU fan direction, based on the system fan modules that are inserted in the chassis. Do not mix power
supplies and fan modules with different air flow directions. Such mixing leads to a system shutdown.
Do not mix power supplies and fan modules with different air flow directions. This will lead to a system
shutdown.
Filters are not mandatory. At any given time, the system may have either a port side intake filter or a port side
exhaust filter, and not both.
Note
Hardware Installation Guide for Cisco NCS 5000 Series Routers
12
Overview
Cisco NCS 5064
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82

Cisco Network Convergence System 5000 Series Installation guide

Network Convergence System 5000 Series
Cisco
Brand
Cisco
Model
Network Convergence System 5000 Series
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents