2. JELD-WEN
  3. JW177200557

JELD-WEN JW177200557 User manual

  • Hello! I am an AI chatbot trained to assist you with the JELD-WEN JW177200557 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
• Aminimum33/8"widejambdepth(“opening”)mustexistfor
replacementjambliners).
• Iftheexistingwindowsillisnotsquare,levelandplumbinstallation
maybecomplicatedandadditionaltrimworkmaybeneeded.Consider
professionalinstallationassistance.
• Usetheworksheetonpage3torecordmeasurementsforeachwindowto
bereplaced.Useadditionalcopiesasneededformorewindows.
• Recordeachwindow’slocationinthehouseontheworksheetinamanner
thatclearlyidentiesit.
• Ifthereismorethan1/8"deviationwithineachsetofmeasurements,
investigatethecauseandseekprofessionalassistancetocorrectproblems.
• Performallmeasurementsoneachwindowbeforegoingtothenextwindow.
• Individuallymeasureeachexistingwindowtobereplaced.Donotassume
similarlookingwindowsareexactlythesamesize.
• Measureaccurately,tothenearest1/8".
• Measurethewidthbetweenthe
sidejambs(woodsurfacetowood
surface)inthreeplaces:top,middle
andbottom.
• Temporarilyremovejambliners
ifnecessaryandavoidanystops,
weatherstrip,balancecords,
pulleys,etc.
• Recordyourmeasurementson
theworksheet.
• Ifinstallingyourreplacement
windowintoawooddouble-hung
withaslopedsill,verifythatthe
slopeis14°or8°.Recordtheslope
angleontheworksheet.
• Foryourconvenience,wehave
includedatemplateatthebottom
rightcornerofthispagetohelp
youdetermineifyouhavea
standardsillslopeangle.Justfold
orcutthispage(oranothersheet
ofpaper)alongthedashedred
lines.Theangleformedbythe
dashedlinesshouldbethesame
astheangleformedbythesill.
• Slightlyopenbothsashesand
threadthetapemeasurebetween
thesashes.
• Atthetop,measuredirectlyfrom
theheadjamb,avoidinganystops,
weatherstripandliners.
• Atthesill,measuretothetopof
theslopedsillontheexteriorside
ofthelowersash.
• Measuretheheightattheleftside,
middleandrightside.
• Recordyourmeasurementson
theworksheet.
Head
Sill
Wood side
jamb
Wood side
jamb
Interior stop
Parting stop
Exterior stop
Jamb depth
min. 3 3/8"
Measuring
locations
Head
stop
Head
jamb
Upper
sash
Exterior
Edge of
paper
template
Lower
sash
Sloped
sill
Sash
Measure
between
sashes
ThankyouforchoosingaJELD-WENWoodorCladWoodDouble-HungSashReplacementKit.Pleasereadthisdocumentfullybeforebeginning.Consultyour
localbuildingcodeofcialforapplicablecodesandregulations(particularlyregardingminimumegressrequirements).Theinstallationofareplacementwindow
willnoteliminateinstallationormaintenanceproblemswithanexistingwindow.Problemssuchaswooddecayandwaterleaksaroundtheexistingframemust
beinvestigatedandxedpriortoinstallingreplacementsashes.Windows produced to user specied dimensions cannot be returned. Besuretheprovided
measurementsarecorrect.
IMPORTANT INFORMATION MEASURE THE HEIGHT
2
MEASURE THE WIDTH
1
CHECk yOUR SILL ANGLE
3
LAy ALONG TOP OF SILL
LAy ALONG OUTSIDE OF SASH
14°
8°
Sill
Measurement Guide
for Wood/Clad Wood Double-Hung Sash Replacement Kits
(JMI002)
1
• Conrmtheexistingwindow
issquarebymeasuringboth
diagonals.Ifthetwodiagonal
measurementsdifferbymorethan
1/4",anout-of-squareadjustment
inthewidthofthewindowmust
bemade.
• Theadjustmentisdeterminedby
creatingaplumbline(usingalevel)
fromeachcornertothesillorhead.
Usingaplumblinethatfallswithin
thewindowopening,measurethe
outofsquareadjustment.
• Subtractthismeasurementfrom
thesmallestwidthmeasurement.
Recordthisadjustedwidthasthe
smallestwidth.
Adjustment
Measuring
locations
Head
Sill
CONFIRM SQUARENESS OF EXISTING WINDOW
4
ADDITIONAL OPTIONS TO BE CONSIDERED
Bepreparedtodiscussthefollowingaboutyourorderwithyourdealer:
• ExteriorFinish:
• ExteriorCladColor
• NaturalorPrimedExterior
• Sizing
• JambLinerColor
• GrillePatterns
• EnergyEfciencyRequirements
• BuildingCodeRequirements
Measurement Guide
for Wood/Clad Wood Double-Hung Sash Replacement Kits
(JMI002)
2
New Window: Location, Style & Grille Pattern Width Measurements (to nearest 1/8") Height Measurements (to nearest 1/8")
Location: ____________________
_____________________________
Glass options:
Clear
Tint
Texture
Low-E
Neat
Tempered
Top:
_________
Middle:
_________
Bottom:
_________
Left:
_________
Middle:
_________
Right:
_________
Smallestwidthmeasurement:________ Smallestheightmeasurement:________
SillAngleMeasurement:
14
°
sill
8
°
sill
New Window: Location, Style & Grille Pattern Width Measurements (to nearest 1/8") Height Measurements (to nearest 1/8")
Location: ____________________
_____________________________
Glass options:
Clear
Tint
Texture
Low-E
Neat
Tempered
Top:
_________
Middle:
_________
Bottom:
_________
Left:
_________
Middle:
_________
Right:
_________
Smallestwidthmeasurement:________ Smallestheightmeasurement:________
SillAngleMeasurement:
14
°
sill
8
°
sill
Location: ____________________
_____________________________
Glass options:
Clear
Tint
Texture
Low-E
Neat
Tempered
Top:
_________
Middle:
_________
Bottom:
_________
Left:
_________
Middle:
_________
Right:
_________
Smallestwidthmeasurement:________ Smallestheightmeasurement:________
SillAngleMeasurement:
14
°
sill
8
°
sill
Location: ____________________
_____________________________
Glass options:
Clear
Tint
Texture
Low-E
Neat
Tempered
Top:
_________
Middle:
_________
Bottom:
_________
Left:
_________
Middle:
_________
Right:
_________
Smallestwidthmeasurement:________ Smallestheightmeasurement:________
SillAngleMeasurement:
14
°
sill
8
°
sill
JMI002 8/18
Location: ____________________
_____________________________
Glass options:
Clear
Tint
Texture
Low-E
Neat
Tempered
Top:
_________
Middle:
_________
Bottom:
_________
Left:
_________
Middle:
_________
Right:
_________
Smallestwidthmeasurement:________ Smallestheightmeasurement:________
SillAngleMeasurement:
14
°
sill
8
°
sill
Nogrilles
Equallite
pattern
Standard
prairie
Custom
(discuss
patternwith
dealer)
Measurement Guide
for Wood/Clad Wood Double-Hung Sash Replacement Kits
(JMI002)
3
Nogrilles
Equallite
pattern
Standard
prairie
Custom
(discuss
patternwith
dealer)
Nogrilles
Equallite
pattern
Standard
prairie
Custom
(discuss
patternwith
dealer)
Nogrilles
Equallite
pattern
Standard
prairie
Custom
(discuss
patternwith
dealer)
Nogrilles
Equallite
pattern
Standard
prairie
Custom
(discuss
patternwith
dealer)
©2018JELD-WEN,inc.;ThispublicationanditscontentsareownedbyJELD-WEN,inc.andareprotectedundertheU.S.CopyrightActandotherintellectualpropertylaws.Alltrademarks,servicemarks,logos
andthelike(whetherregisteredorunregistered)areownedorcontrolledbyJELD-WEN,inc.orothers.UnauthorizeduseorduplicationofJELD-WENintellectualpropertyisprohibited.
JELD-WENreservestherighttochangeproductspecicationswithoutnotice.Pleasecheckourwebsite,jeld-wen.com,forcurrentinformation.
/