• Aminimum33/8"widejambdepth(“opening”)mustexistfor

replacementjambliners).

• Iftheexistingwindowsillisnotsquare,levelandplumbinstallation

maybecomplicatedandadditionaltrimworkmaybeneeded.Consider

professionalinstallationassistance.

• Usetheworksheetonpage3torecordmeasurementsforeachwindowto

bereplaced.Useadditionalcopiesasneededformorewindows.

• Recordeachwindow’slocationinthehouseontheworksheetinamanner

thatclearlyidentiesit.

• Measurethewidthbetweenthe

sidejambs(woodsurfacetowood

surface)inthreeplaces:top,middle

andbottom.

• Temporarilyremovejambliners

ifnecessaryandavoidanystops,

weatherstrip,balancecords,

pulleys,etc.

• Recordyourmeasurementson

theworksheet.

includedatemplateatthebottom

rightcornerofthispagetohelp

youdetermineifyouhavea

standardsillslopeangle.Justfold

orcutthispage(oranothersheet

ofpaper)alongthedashedred

lines.Theangleformedbythe

dashedlinesshouldbethesame

astheangleformedbythesill.

• Slightlyopenbothsashesand

threadthetapemeasurebetween

thesashes.

• Atthetop,measuredirectlyfrom

theheadjamb,avoidinganystops,

• Atthesill,measuretothetopof

theworksheet.

Head

Sill

Wood side

jamb

Wood side

jamb

Head

jamb

Upper

sash

Exterior

Edge of

paper

template

Lower

sash

ThankyouforchoosingaJELD-WENWoodorCladWoodDouble-HungSashReplacementKit.Pleasereadthisdocumentfullybeforebeginning.Consultyour

localbuildingcodeofcialforapplicablecodesandregulations(particularlyregardingminimumegressrequirements).Theinstallationofareplacementwindow

willnoteliminateinstallationormaintenanceproblemswithanexistingwindow.Problemssuchaswooddecayandwaterleaksaroundtheexistingframemust

beinvestigatedandxedpriortoinstallingreplacementsashes.Windows produced to user specied dimensions cannot be returned. Besuretheprovided

measurementsarecorrect.

IMPORTANT INFORMATION MEASURE THE HEIGHT

2

MEASURE THE WIDTH

1

CHECk yOUR SILL ANGLE

1

• Conrmtheexistingwindow

issquarebymeasuringboth

diagonals.Ifthetwodiagonal

measurementsdifferbymorethan

1/4",anout-of-squareadjustment

inthewidthofthewindowmust

outofsquareadjustment.

• Subtractthismeasurementfrom

thesmallestwidthmeasurement.

Recordthisadjustedwidthasthe

smallestwidth.

Sill

• NaturalorPrimedExterior

• Sizing

• EnergyEfciencyRequirements

• BuildingCodeRequirements

2

New Window: Location, Style & Grille Pattern Width Measurements (to nearest 1/8") Height Measurements (to nearest 1/8")

Location: ____________________

_____________________________

Glass options:

 Clear

 Tint

 Texture

 Low-E

Top:

Middle:

Bottom:

Left:

Location: ____________________

_____________________________

Glass options:

 Clear

 Tint

Top:

Middle:

Bottom:

Left:

3

pattern

 Standard

prairie

 Custom

(discuss

patternwith

dealer)

©2018JELD-WEN,inc.;ThispublicationanditscontentsareownedbyJELD-WEN,inc.andareprotectedundertheU.S.CopyrightActandotherintellectualpropertylaws.Alltrademarks,servicemarks,logos

andthelike(whetherregisteredorunregistered)areownedorcontrolledbyJELD-WEN,inc.orothers.UnauthorizeduseorduplicationofJELD-WENintellectualpropertyisprohibited.

JELD-WENreservestherighttochangeproductspecicationswithoutnotice.Pleasecheckourwebsite,jeld-wen.com,forcurrentinformation.