888-45-204-W-00rev. D • 01/14
1 of 5
2
1
13 mm17 mm
StyleView Sit Stand Combo Arm Extender
AB CD
1
2
3
180˚*
360˚
360˚
4x
3 mm
6 mm
1x
1x
1x
1x 1x
1x
1x
1x
1x
1x
1x
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ENGLISH
For the latest User Installation Guide please visit: www.ergotron.com
User's Guide
*Product shipped with rotation stop in place to prevent the Extender from hitting the wall.
888-45-204-W-00rev. D • 01/14
2 of 5
1
5.63”
(143 mm)
6.93”
(176 mm)
1.38”
(35 mm) Ø 0.43”
(11 mm)
2.64”
(67 mm)
Back View
5’3”-5’9”
(160-175cm)
21”
(533 mm)
27.25”
(692mm)
< 26.25”
(667mm)
5’3”-5’9”
(160-175cm)
21”
(533 mm)
31.5”
(800mm)
< 30.5”
(775mm)
Combo Arm With Worksurface
Combo Arm Without Worksurface
Combo Arm Extender
6”
(152 mm)
29.2”
(741mm)
13.7”
(347mm)
8.3”
(211mm) 4.1”
(105mm)
33.7”
(856mm)
24.5”
(621mm)
24.5”
(621mm)
33.7”
(856mm)
25.8”
(656mm)
33.6”
(854mm)
0.28”
(7mm)
29”
(734mm)
10” (252mm)
4.4”
(122mm)
7.7”
(196mm)
30”
(759mm)
20.6”
(524mm)
20.6”
(524mm)
30”
(759mm)
26”
(622mm)
33.4”
(848mm)
0.08”
(2mm)
ENGLISH
NOTE: Fasteners may unwind due to vibration caused by movement of mounting solution over time. Inspect mounting
solution for loose fasteners on a routine basis. If desired, apply a light duty thread locking adhesive to fasteners before
installation to prevent back-out.
Mounting Height for Ergonomic Workstation
This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5’3”-5’9” (160-175cm).
If user heights are di erent than this, you should change mounting height to accommodate user heights. (Change mounting height
one inch for every one inch di erence in user heights).
Mounting height assumes there is a 6” (152 mm) distance between the center
of your monitor mounting holes and the top of the screen. If your distance is
smaller, you should increase mounting height accordingly, if your distance is
larger, you should decrease your mounting height accordingly.
Determine mounting location:
Determine mounting location:
Top view showing range of motion when pulled out
from the wall.
Front view with arm pushed back against the wall.
Front view with arm pushed back against the wall.
888-45-204-W-00rev. D • 01/14
3 of 5
2
3
4
1x
1x
3 mm
17 mm
1/4"
(6.4mm)
ENGLISH
IMPORTANT! Torque bolts in the sequence shown above to a minimum of 50 lb-ft (6.91 kgf-m).
888-45-204-W-00rev. D • 01/14
4 of 5
5
6
13 mm
4x
ENGLISH
888-45-204-W-00rev. D • 01/14
5 of 5
ENGLISH
For local customer care phone numbers visit: http://contact.ergotron.com
Learn more about ergonomic computer use at:
www.computingcomfort.org
Set Your Workstation to Work For YOU!
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists at.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain at.
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ergotron 45-260-026 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Asoka PlugLink AV 9660 User manual
-
ASOKA USA T37PL9661-I2 User manual
-
Pride Mobility Pride Power Lift Recliner Owner's manual
-
Life Fitness V2 User manual
-
Pride Mobility Power Lift Recliner Owner's manual
-
HoMedics IB-SC475 User manual
-
-
FitDesk 3131 User guide
-
-
