2. APC
  3. PBS-KW
PBS-KW

APC PBS-KW User manual

  • Hello! I've reviewed the user manual for the APC push button switches, including models PBS-KW and PBD-KW. This document outlines the specifications, setup, and pairing procedures for these devices. I'm ready to answer any questions you have about the push buttons, from their range and power requirements to their pairing procedure.
  • What is the operating range of the wireless push button?
    What is the IP rating of the push button?
    What kind of battery does the push button use?
Swing Gate Position 1
Sliding Gate Position 1
Swing Gate Position 2
Sliding Gate Position 2
Control Board
Wireless Push Button Pairing Procedure
- Over 50m Operating Range
- Robust ABS Plastic Design
- Powered by 23A 12V Battery
- Configurable Function
- ON/OFF Lockout Key Switch
- IP Rating 64
- 0 mA Standby / 16m A Working Consumption
Open/Close
ON
OFF
PBS-KW
Open/Close
Open/Close
Full
Gate
Pedestrian
Gate
ON
OFF
PBD-KW
APC
Automation Systems
APC
Automation Systems
PBS-KW
(Single Push Button Switch)
PBD-KW
(Double Push Button Switch)
B
A
Open/Close
Open/Close
ON
OFF
PBD-KW
Automation Systems
APC
Button Terminal
“A” Function Jumper
Button Terminal
“B” Function Jumper
1 2 3 4
1 2 3 4
ON DIP
ON DIP
+-A
A
B
B
Button Terminal “A”
Button Terminal “B”
Use the relevant instruction set located on one of the
following pages to pair your wireless push button.
STEP 1 Setting your push button feature
STEP 2 Control Board Identification STEP 3 Pairing Procedure
Specifications
Note: ONLY one feature per DIP Switch can be enabled
Example: If the remote number 2 button operates the gate partially set the number 2 DIP
switch to the on position for the same feature.
Simply turn the respective DIP switch to the ON position that relates to the button on your
remote control.
Using the DIP switch associated with the button in use (see linked diagrams on the left). You
can adjust your DIP switch to enable it to toggle a specific feature.
B
Open/Close
ON
OFF
PBS-KW
Automation Systems
APC
DIP 1
REMOTE BUTTON 1
DIP 4 REMOTE BUTTON 3
DIP 2
REMOTE BUTTON 2
DIP 3 REMOTE BUTTON 4
1 2 3 4
ON DIP
- Press and hold the REMOTE button on the control board until the LED indicator is on solid then release the REMOTE button.
WARNING: This will delete all wireless equipment from the system.
- Press the small REMOTE button once on the circuit board and the LED Indicator will start to flash.
- Press any of the buttons on the wireless push button for ONE second (ensuring the key is in the ON position)
Press this REMOTE
button once and the
LED indicator will start to
flash.
1
LED
Indicator
Remote
Learning
Button
Pairing
Deleting
REMOTE
CH 1 CH 2 CH 3 CH 4
REMOTE
1 2 3 4
ON DIP
Part No APC-PE2000
Learn CH1/CH2
Learn CH3/CH4
CH 3 CH 4
CH 1 Double Gate Opening
CH 2 Single Gate Opening
CH 3 Party Mode
(Cancel Auto Close for one cycle)
CH 4 Pedestrian Gate Unlock
(Lock 2)
1. Press the LEARN CH button once for the channel group you wish
to pair the remote too. (CH1/2 OR CH3/4).
2. Cycle to the desired channel by pressing the LEARN CH button.
(The control panel indicates which channel you are on by flashing the channel’s LED)
3. Press any of the buttons on the wireless push button for ONE second (ensuring the key is in the ON position)
Repeat the above process for any additional remote’s or wireless buttons that require programming.
1. PRESS AND HOLD the LEARN CH button for the channel group you wish to delete until the channel groups LED’s begin
flashing simultaneously.
2. Release the LEARN CH button and wait for the LED’s to stop flashing.
3. If the LED’s Simultaneously flashed 3 times then stopped you have successfully deleted the remote’s and/or buttons from
this channel group..
WARNING: This will delete all wireless equipment from the system.
Pairing
Pairing
Deleting
Deleting
2
Press the wireless push button for one second
2. Press SET button to clear the memory
1. Press SELECT button two/three time until cycled to the Learn Remote D-Gate (Double gates) or Learn Remote S-Gate (Single gates) LED
WARNING: This will delete all wireless equipment from the system.
Learn
Remote
D-Gate
Learn
Remote
S-Gate
Inhibitor
ON/
OFF
Learn
Time
Double
Learn
Time
Single
Auto
Close
Time
Motor 2
Delay
Auto /
Step By
Step
Learn Remote
Double Gate
Learn Remote
Single Gate
2. Press any of the buttons on the wireless push button for ONE second (ensuring the key
is in the ON position)
1. Press SELECT button two/three times until cycled to the Learn Remote D-Gate (Double gates) or
Learn Remote S-Gate (Single gates) LED.
APC-CBSW12 /APC-CBSW24
APC-CB12-4CH /APC-CB24-4CH
APC-CBSW240AC
Swing Gate Systems
- Turn off system power
- HOLD the button on the receiver whilst powering the system ON
- The LED’s will blink FOUR times to indicate the process is complete, now the button can be released.
WARNING: This will delete all wireless equipment from the system.
- Press the button on the receiver once and the LED Indicator will start to flash.
- Press any of the buttons on the wireless push button for ONE second (ensuring the key is in the ON position)
Press the receiver
button once and the
LED indicator will start to
flash.
1
LED
Indicator
Remote
Learning
Button
Pairing
Deleting
2
Press the push button one time
APC-LOGICO 24
Swing Gate Systems
- Press and hold the REMOTE button until the LED indicator is on solid then release the REMOTE button.
WARNING: This will delete all wireless equipment from the system.
- Press the small REMOTE button once on the circuit board and the LED Indicator will start to flash.
- Press any of the buttons on the wireless push button for ONE second (ensuring the key is in the ON position)
LED
Indicator
Remote
Learning
Button
REMOTE
CH 1 CH 2 CH 3
1 2 3
ON
Receiver
Pairing
Pairing
Pairing
Deleting
Deleting
Deleting
Clearing the memory (Formatting)
- Press and hold the STUDY button for 5 seconds and a small BEEP will be heard. Release the STUDY button and all
wireless equipment will be deleted.
WARNING: This will delete all wireless equipment from the system.
- Press the small STUDY button for ONE SECOND then release.
- Press any of the buttons on the wireless push button for ONE second (ensuring the key is in the ON position).
Clearing the memory (Formatting)
- Press and hold the Auto Learn button for 7 seconds and the Green Auto Learn LED will start flashing, release
the black button after 3 flashes and all wireless equipment will be cleared.
WARNING: This will delete all wireless equipment from the system.
- Press the small AUTO LEARN button once and the AUTO LEARN Green LED will turn on.
- Press any of the buttons on the wireless push button for ONE second (ensuring the key is in the ON position)
LED
Indicator
Remote
Learning
Button
Remote
Learning
Button
Auto
Learn
Power
Stop
Auto
Close
1 2 3 4
ON DIP
APC-CBSG12 / APC-CBSG24
APC-CBSG240AC V2
APC-CBSG240AC
CB-SGH/ CB-SGX
Learn Code
LED2LED1
LED2 Full Gate Opening
LED1 Pedestrian Function/Party Mode (refer to
installation manual)
1. Press the LEARN CODE button once/twice to cycle to the function you wish to pair the remote
button too.
2. Press any of the buttons on the wireless push button for ONE second (ensuring the key is in the ON position)
Repeat the above process for any additional remote’s or wireless buttons that require programming.
1. PRESS AND HOLD the LEARN CODE button until BOTH LED’s begin to flash simultaneously then release.
WARNING: This will delete all wireless equipment from the system.
Pairing
Deleting
Press this REMOTE
button once and the
LED indicator will start to
flash.
12
Press the wireless push button for one second
Press this STUDY
button once and the
LED indicator will start to
flash.
12
Press the wireless push button for one second
Press this AUTO LEARN
button once and the
LED indicator will start to
flash.
12
Press the wireless push button for one second
Sliding Gate Systems
- Turn off system power
- HOLD the button on the receiver whilst powering the system ON
- The LED’s will blink FOUR times to indicate the process is complete, now the button can be released.
WARNING: This will delete all wireless equipment from the system.
- Press the button on the receiver once and the LED Indicator will start to flash.
- Press any of the buttons on the wireless push button for ONE second (ensuring the key is in the ON position)
Press the receiver
button once and the
LED indicator will start to
flash.
1
LED
Indicator
Remote
Learning
Button
Pairing
Deleting
2
Press the push button one time
APC-P450 / APC-P500/APC-P1000
Sliding Gate Systems
/