OPERAT
OR’S MANUAL
650532–X
RELEASED:
3–6–95
(REV
. A) IPP
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
PUMP
SYSTEM
650532–1
%! ' '% (( "'" % "!%& &$ ! %&
21.7:1
RA
TIO
3” AIR MOTOR
2 1/4” STROKE
650533–X
650533–1
READ THIS MANUAL CAREFULL
Y BEFORE INST
ALLING,
OPERA
TING OR SER
VICING THIS EQUIPMENT
.
CARBON STEEL
ST
AINLESS STEEL
1995
THE ARO CORPORA
TION
PRINTED IN U.S.A.
(419) 636–4242
F
AX (419) 636–21
15
THE ARO CORPORA
TION
ONE ARO CENTER
BR
Y
AN, OHIO 43506–0151
.-31.+ !-%+
%% !'%
!3%1)!+
43+%3
4,/ )1
!-)&.+$
.13!")+)38 )3
/3).-!+
'$
SERVICE KITS
• 2% .-+8 '%-4)-% 1%/+!#%,%-3 /!132 3. !2241% #.,/!3)"+%
/1%2241% 1!3)-' !-$ +.-'%23 2%15)#% +)&%
• &.1 1%/!)1 .& )1 .3.1 %#3).-
• &.1 1%/!)1 .& .6%1 4,/
GENERAL
DESCRIPTION
WARNING ! !& ( (' !"$&
"$%%'$ ! "% $ & "%
$ $ & "$%%'$
WARNING $$ &! $ !$&! %&
!$ &! %&) "$'&! % "!$;
& & !$&!
8 $%+)5%1)-' ! 2,..3( #.-3)-4.42 "%!$ .& 3(% /1./%1 2)9% !-
2823%, (%+/2 3(% ./%1!3.1 ,!)-3!)- ".3( ()2 /1.$4#3).- 1!3% !-$ /1.:
$4#% 04!+)38 23!-$!1$2 !)-3!)-%$ 04!+)38 23!-$!1$2 !2241%2 3(!3 3(%
,!3%1)!+ "%-%&)32 !1% 1%!+)9%$ . &413(%1 ,!7),)9% ./%1!3.1 /1.$4#3).-
3),% 3(% 823%, (!2 ! "4)+3)- +)&31!, &%!341% &.1 04)#* !-$ %!28
$14, #(!-'%.5%1
823%,2 !1% 3.3!++8 %-#+.2%$ 2%!+)-' 3(% ,!3%1)!+ )- 3(% 2823%,
&1., !)1 !-$ ,.)2341% /1%5%-3)-' /1%,!341% #41%.43 .& 3(% ,!3%1)!+
()2 !++.62 &.1 %)3(%1 #.-3)-4.42 .1 )-3%1,)33%-3 42% .& 3(% 2823%, !-$
1%$4#%2 3(% -%%$ &.1 $!)+8 2823%, #+%!-4/
4)+3)- +)&3 #!/!")+)38 !++.62 &.1 04)#* $14, #(!-'%.5%1 !-$ %!28 +)&3)-'
.& /4,/ !22%,"+8 &1., #.-3!)-%1
(% 1!3). )2 !- %7/1%22).- .& 3(% 1%+!3).-2()/ "%36%%- 3(% %&&%#:
3)5% !)1 ,.3.1 !1%! !-$ 3(% %&&%#3)5% +.6%1 /4,/ !1%! (%-
"!1 .& !)1 /1%2241% )2 24//+)%$ 3. 3(% !)1 ,.3.1 3(% +.6%1 /4,/ !1%!
6)++ $%5%+./ ! ,!7),4, .& "!1 .& &+4)$ /1%2241% !3
-. &+.6 !2 3(% &+4)$ #.-31.+ )2 ./%-%$ 3(% &+.6 1!3% 6)++ )-#1%!2% !2 3(%
!)1 ,.3.1 #8#+% 1!3% )-#1%!2%2 3. *%%/ 4/ 6)3( 3(% $%,!-$
MAJOR COMPONENTS LIST
7-1 -6,5/47/32 #7: "*57 3 7-1 -6,5/47/32 #7: "*57 3
%/2.0- "367 $*1 *6/, "814 66-1+0: "
30039-5 "0*7- *6/, "814 66-1+0: "
30039-5 "0*7- !"&! #'" &
"357*+/0/7: /7
INSTALLATION
The 65053X-X Chop-Check Dispensing System comes completely
assembled. Remove unit from crate and place on a level surface.
Install material hose and dispensing device as required.
When the following instructions are observed, heavy paste materials
can be pumped directly from their original 5 gallon drum without air inĆ
clusion, or excessive waste. The follower plate creates an air tight seal
as well as clean-wiping action in its progressive downward movement
into the drum.
OPERATING INSTRUCTIONS
" !" #"! " !"# #
WARNING !" %0-6 :)1;16/ 7: 47?-:16/ <0-
41.< Read the warning on page 2 of 651615 Single Post Lift/Ram
Operator's Manual.
"
!!#
#"
% "
!#' $$
"
$
" !
#
#
" #"
"
"
!!#
#
" ! " " !" "
1. Take note of the pump/drum clearance above. Be certain the lift is
clear of any objects above. Also refer to OPERATING AND SAFEĆ
TY PRECAUTIONS found on page 2 of 651615 Single Post Lift/
Ram Operator's Manual.
2. Connect the air supply (160 PSI MAX) to the air inlet. Adjust (Turn Lift/
Ram Pressure Regulator Knob Clockwise) air pressure on lift/ram presĆ
sure regulator to 20 P.S.I. (1.2 Bar)
3. Shift the control valve lever to the ``UP'' position.
4. Raise the lift high enough to clear the height of the drum. Stop the
lift upward travel by moving the control valve lever to the (center)
``NEUTRAL'' position.
"
1. Once lift assembly and pump are in the ``UP" position, place and
center an opened 5 gallon drum of material on the lift/ram base.
Use the stops on the base to center 5 gallon drum. Tighten thumb
screw to secure drum.
2. Lubricate lower follower wiper plate seal with any type grease. (siliĆ
cone, vaseline, gear, etc.) This ensures a smooth fit into the pail as
well as prevents curing type compounds from bonding to seal.
3. Check vent plug on follower plate to be sure it easily threads in and
out. It is recommended to lubricate the threads of the plug to help
prevent possible set up of compound at this point. !-- &&
8-:)<7:; )6=)4
" % "
WARNING
( 7447?-: +)6 ,-;+-6, 9=1+34@
+)=;16/ 162=:@ --8 0)6,; +4-): ?0-6 )41/616/ ?1<0 +76<)16A
-: Read the warning on page 2 of 651615 Single Post Lift/Ram
Operator's Manual..
" - +-:<)16 <0- 7447?-: 4)<- >-6< 84=/ 0); *--6 :-57>-,
so that the air trapped between the follower and the material is allowed
to escape from this vent. Captured air between the follower plate and
drum will escape.
" The lift may hesitate momentarily before starting downward,
the air pressure inside the post air chamber must decrease before it
will begin to descend.
1. Shift the control valve lever to the ``DOWN'' position and proceed
to lower the pump.
2. Replace the vent plug once the material begins to ooze from the
vent opening.
3. The unit is now ready for operation. Adjust (Turn pump regulator
Clockwise) air pressure on pump Filter/Regulator until pump beĆ
gins to cycle.
4. Trigger gun to prime pump with material.
" ! " "
1. Adjust the Follower Plate Air Valve pressure up to approximately 8
psig. DO NO OVERPRESSURIZE THE DRUM to avoid damage.
NOTE: Air from this valve will only pass when the Control Lever is
in the ``UP'' position.
2. Shift the control valve lever to the ``UP'' position.
3. Raise the lift high enough to clear the height of the drum. Stop the
lift upward travel by moving the control valve lever to the (center)
``NEUTRAL'' position.
" #
" The Control Lever should be in the ``NEUTRAL'' position.
1. Unsrew thumb screw and remove old 5 gallon drum.
2. Place and center. a new drum into position. Remove cover. TightĆ
en thumb screw.
"
%% ! !
.4 1/+6
470 623
.4 25+
#+16 /7,
!-70( )4+8
"
%%%%
64++6 /(28
&
& *'36+4
! % !
!
'6+4.'/ 76/+6
)4+85 &
$'5-+45 &
$ !
"& ##
/
