2. Computers & electronics
  3. Print & Scan
  4. Printer
  5. X1 FAQ

Printer X1 FAQ Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Printer X1 FAQ Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
X1PrinerFAQManual
Problem1:3DPrinternotprint
ProbableCause
solution
picture
1.gcodefilenotcorrect
3Dprintercanonlyprintgcode
file,thefilenamecannothave
specialsymbols,onlynumbers
orletters
2.formattheTFcard
formattheTFcardtoFAT
3.Ifthenozzleisnotheated
orthetemperatureisnot
measured,thefeedinglight
flashallthetime
checkthecableconnectors,or
replacetheNozzle
4.Thecardslotonthemain
boardisbroken
replacemotherboard
Problem2:withoutfilamentsilkcomeoutfromnozzle
ProbableCause
solution
picture
1.TheEmotorcableisnot
connectedproperly
checkthecableconnector
2.TheEmotordamaged
replacetheExtrudermotor
3.Thewireofthermistorfalls
offorburnsout
checkthecableconnector,or
replacetheNozzle
4.Theheatingringlinefalls
off,ordamaged
checkthecableconnector,or
replacetheNozzle
Problem3:Nozzlespitoutfilamentisnotvertical
ProbableCause
solution
picture
1.nozzlenogood
replacenozzle
2.Ttisnotcleaninsidethe
Teflontube
replaceTeflontube
3.Theplatformisnotleveled
properly.Thenozzleand
platformcollideduring
printing,andthenozzleis
damaged
Preventthenozzlefrom
scrapingtheplatformbefore
print
Problem4:XAxisnotwork,orprintshift
ProbableCause
solution
picture
1.XAxiscableconnect
loose
checkthecableconnector
2.Xmotordead
replacetheYmotor
3.Xlimitswitchwireconnect
loose
openthecontrolboxtocheck
thisitlooseornot
4.Belttooloosemaycause
printshift,Belttootightmay
causehardtomove
Adjustbelttightness
1)，loose4screws,justloose
2),Useatooltopushthex-axis,
andadjustthebelttightness
3),fixthetopfourscrewstightly
again
5.Xaxlesleevetootight
replaceaxlesleeveorAdd
somelubricatingoil.
Problem5:YAxisnotwork,orprintshift
ProbableCause
solution
picture
1.YAxiscableconnect
loose
checkthecableconnector
2.Ymotordead
replacetheYmotor
3.Ylimitswitchwireconnect
loose
openthecontrolboxtocheck
thisitlooseornot
4.Belttooloosemaycause
printshift,Belttootightmay
causehardtomove
Adjustbelttightness
5.Yaxlesleevetootight
replaceaxlesleeveorAdd
somelubricatingoil.
Problem6:ZAxisnotwork
ProbableCause
solution
picture
1.thepowerconnectormay
loose
checktheconnector
2.Zmotordead
replaceZmotor
3.Zlimitswitchwire
connectloose
openthecontrolboxtocheck
thisitlooseornot
4.ZBelttooloose
Adjustbelttightness
1)，loose4screws,justloose
2),Useatooltopushthex-axis,
andadjustthebelttightness
3),fixthetopfourscrewstightly
again
Problem7:Printernotwork,nofunction
ProbableCause
solution
picture
1.checkifthepoweradaptor
isgoodornot
checkifthelightison
2.firmwareproblem
updatefirmware
3.Thebuttonboardis
damaged,noresponsetothe
button
replacethecontrolboard
4.Themainboardisburnt
out
replacethemainboard
CommonFAQfor3DPrinter
1),Whyistheprintingmodelnotadhesivetotheprintingbed.
A1: The nozzle is too far away from the bed, the proper distance between the nozzle and bed is the thickness of a piece of A4 paper .
2),Whythefilamentdonotcomeoutfromthenozzle.
A1: Check the filament extruder gear rotates or not. and check if filament feeder Extruder motor is connected well or not.
A2, Check temperature of sliced gcode. Printing nozzle temperature of PLA material range s from 180-230℃.
A3, Check if the nozzle is blocked. Do feeding ,use your hand help to push the filament gently , if there is no filament come out , then need
clean the nozzle or replace it .
A4, Check if nozzle is too close to platform , if so, the filament can not come out, then need do right leveling again.
3),TheproblemofprintmodelshiftXorYdirection.
A1, The model did not slice properly, need to re-slice or change the model position to generate new Gcode file.
A2,The model file problem, If you print ather models has no problem, Perhaps the original file problem .
4),Whytheprintingeffectislow.
A1, There is a lot of filament piled up on the model surface
A1.1, Nozzle temperature is too high, filament melt too fast and caused overflowing .
A1.2, The filament flow is too large, there is filament flow setting in slice software , change the default value 100% to be 80%.
A1.3, Filament diameter setting problem , it’s in slice software, the default settings are different , there are both 1.75mm and 3mm filament
on the market, for 1.75mm, the diameter should be 1.75 , but for 3mm, the diameter should be 2.85 or 2.95 .
A2 , Poor surface after removing the support for FDM technology, The support density should be as lower as possible, 10% is proper, it’s easy
to remove.
A3, The filament quality is poor
/