Triax 157011 Operating instructions

Brand: Triax

Model: 157011

Type: Operating instructions

Triax 157011 is a powerful LAN Network Tester that can help you quickly and easily prevent and solve network cable installation problems. It can check telephony and data cable installations and carry out a number of tests such as cable connection sequence, length, user jumper, cable connection continuity and can detect open circuits, short circuits, jumper or cross-talk interference. With Triax 157011 you can locate the wiring or connection error, it measures the cable length and estimates the distance to the open circuit or short circuit fault. Triax 157011 is simple and easy to use.

LAN Network Tester

Part No. 157011

Operating Manual

TRIAX - your ultimate connection

The LAN Network Tester operates o 6V DC only.

Only use the internal, battery powered, 6V power supply to power the LAN Network

Tester. Never connect or use any other power supply to power up the LAN Network

Tester otherwise damage to the tester may result or test results could be aected.

Ensure that the batteries are correctly inserted.

Refer to the polarity symbols within the battery compartment.

To ensure ecient use and increase battery life, the LAN Network Tester will

automatically switch o following 30 minutes of inactivity.

Disposal: For proper treatment, recovery and recycling, please take this product,

(including any used batteries), to designated collection points.

Safety and Disposal

Contents

Product Overview 3

Features 3

Interface and Key Description 4

Operation Procedures 5

Wiring Diagrams and Test Functions 6

Pair and Length Measurement 9

Coaxial Cable and Telephone Line

Measurement Function 11

Calibration and Setup Function 12

Dynamic Calibration 12

Technical Specication 14

The LAN Network Cable Tester is a powerful tool which can:

• Help prevent and solve network cable installation problems.

• Check telephony and data cable installations.

• Carry out a number of tests such as cable connection sequence, length, user

jumper, cable connection continuity and can detect open circuits, short circuits,

jumper or cross-talk interference.

• Reduce cable installation cost and save cable installation time.

Product Overview

• Only requires one person to complete cable continuity checks.

• Checks for wiring errors in CAT 5e / 6 cable, coaxial cable and telephone lines.

• Errors such as open circuit, short circuit, jumper wire, reverse connection or

cross-talk interference can be detected.

• Locates the wiring or connection error.

• Measures the cable length and estimates the distance to the open circuit or short

circuit fault.

• Dynamically calibrates cable length and carries out cable length measurement to

an accuracy of 97%.

• Simple and easy to use. The large LCD screen clearly displays the test results.

• Portable unit with long battery life.

• Automatically switches o if left unused for 30 minutes.

• Measures length and pair with or without far-end recogniser.

• Locates cables. There can be up to 8 far-end passive test jacks (ID No: ID 1-ID8).

• Self-checking function and automatic compensation for any change in battery

capacity or ambient temperature.

Features

Power Supply

The tester uses 4 x 1.5V size ‘AA’ alkaline batteries with power consumption 16mA

(Included). The batteries should be removed if the tester is not used for a long

time to prevent the battery pack from leaking which will result in corrosion. (Note

disposal advice on page 1).

LAN Network Cable Tester Front Panel and Ports:

Interface and Key Description

LOOPBACK Port

MAIN Port

LCD Display Screen

Power Switch

Function Key

Conrmation/Return Key

Function Key

Start and Display

Carries out a self-check, (The dotted line displays the progress of the self-check

from left to right).

Wait 5 seconds or push any key to display the main menu

Main Menu Display

There are 4 functions to select from the main menu:

Wire Map – This wiring diagram measurement is to check end to end continuity of

cables, (M, L and R), and locate errors.

Pair and Length – Pair and length measurement to verify cable length, pen circuit

distance, pairing and cross-talk interference.

Coax/Tel – Coaxial cable and telephone line measurement to check continuity and

indicate open circuit and short circuit faults.

SETUP – Calibrate and set up the Network Cable Tester.

Within the main menu display, press the p or q keys to move the cursor “->” up or

down to the required item and press the ‘PAIR&L’ key on the front panel to enter the

related test function.

Operation Procedures

Wiring Diagram (WIREMAP) test function:

When the wiring diagram, (WIREMAP), test function is selected, the tester will carry

out a wiring diagram (WIREMAP) test and displays the following information while

the check is being carried out:

Test 1: Short Circuit (SHORT)

If there is a short circuit on the cable or terminal, it will be shown on the display.

For example, if the test found 12 short circuits the display would appear as shown

below:

Press the p or q key to restart the test or press the ‘PAIR&L’ key to return to the

main menu.

Always correct a short circuit fault rst and then start further test measurements.

Test 2: Far-end matcher (ID) is not found or the cable is not inserted in local

port (L):

The LAN Network Cable Tester will automatically detect the far-end matcher (ID) or

local port (L) cable. See the image below if the far-end of the cable being checked is

not inserted into the far-end matcher (ID) or if the cable is not inserted into the local

port (L) in a local test:

Press the p or q key to restart the test or press the ‘PAIR&L’ key to return to the

main menu.

Test 3: Normal wiring diagram (WIREMAP) display:

The LAN Network Cable Tester will automatically detect the far-end matcher (ID) or

local port (L) cable and it will display the wiring diagram (WIREMAP). If it nds the

far-end matcher (ID) or the local port (L) on the far-end of the cable being checked,

the display will show the following:

The ‘R:’ line shows the RJ45 jack pin number of the far-end port and ‘ID1’ is the

far-end matcher number.

The ‘|:’ line shows the connecting wire between far-end port and master port.

The ‘M:’ line shows the RJ45 jack pin number of master port.

Press the p or q key to restart the test or press the ‘PAIR&L’ key to return to the

main menu.

Test 4: Wiring diagram, (WIREMAP), display when there is an open circuit at

the far-end of the cable:

On the ‘R:’ line, pins ‘3’ and ‘6’ display ‘x’, indicating an open circuit towards the

far-end plug on pins ‘3’ and ‘6’. The open circuit should be located within 10% of

the cable length measured from the far-end plug.

Note:

If you use the far-end matcher (ID) to measure the wiring diagram (WIREMAP), because the

test is made via the paired cable cores, the open circuit at the far-end always displays in pairs,

as shown above. This is the case whether there is one open circuit or all are open circuits in

the far-end pins ‘3’ and ‘6’. For identication, move the tester to the far-end and repeat the

measurement.

Test 5: Wiring diagram, (WIREMAP), display when there is an open circuit at

the near-end of the cable:

The display will show a wiring diagram, (WIREMAP), as shown below if there is an

open circuit at the near-end plug.

On the ‘M:’ line, pin ‘3’ displays ‘x’, indicating an open circuit towards the near-end

plug on pin ‘3’. The open circuit should be located within 10% of the cable length

measured from the near-end plug.

Test 6: Wiring diagram, (WIREMAP), display when there is an open circuit in the

middle of the cable:

The display will show a wiring diagram, (WIREMAP), as shown below if there is an

open circuit in the middle of the cable:

On the ‘I’ line, pin ‘3’ displays ‘x’, indicating an open circuit in the middle of the

cable on pin ‘3’. The open circuit should be located within 10% - 90% of the cable

length measured from the near-end plug.

For further help in locating open circuits, the pair and length function (PAIR &

LENGTH) of the tester can be used as follows:

Pair and Length measurement (PAIR & LENGTH) function:

Whether or not there is a far-end recogniser, (ID), at the far-end of the cable, the

LAN Network Cable Tester is capable of carrying out a ‘Pair and Length’ (PAIR

& LENGTH) measurement. Therefore, the far-end recogniser, (ID), can remain

connected during a wiring diagram, (WIREMAP), and pair and length (PAIR &

LENGTH) measurement. This avoids it being repeatedly inserted and removed.

When the pair and length (PAIR & LENGTH) measurement function is selected, the

LAN Network Cable Tester display will display an image typical to that shown below

as the measurement is being made:

Note: Due to different technical parameters in various branded cables, the user should carry

out the LAN Network Cable Tester Dynamic Calibration function before making a length

measurement. (See page 12)

Test 1: Short circuit (SHORT)

The LAN Network Cable Tester will display an image typical to that shown below if

there are any short circuits on the cable or terminal, (12 short circuits are shown in

the example below).

(The tester cannot show the exact location of the short circuit). Press the p or q

key to restart the test or press the ‘PAIR&L’ key to return to the main menu.

Always correct a short circuit error rst and then start further test measurements.

Test 2: Normal pair and length (PAIR & LENGTH) display

The LAN Network Cable Tester, in ‘Pair and Length’ mode, will display information

typical to that shown below when the cable is under normal conditions.

It shows the ‘Pair’ line number followed by the cable length.

Press the p or q key to restart the test or press the ‘PAIR&L’ key to return to main

menu.

Test 3: Abnormal pair and length (PAIR & LENGTH) display

If Paired and Unpaired lines are detected in the pair and length (PAIR & LENGTH)

measurement, the LAN Network Cable Tester will display the paired lines rst. See

the example display below:

In the example above, the last line, (78q), indicates there is no pair found in lines

7 and 8. It will display the length of the unpaired line numbers, (as shown below), if

you press the q key.

Press the ‘PAIR&L’ key to return to the main menu.

It will display an ‘x’ to indicate an open circuit if the length is less than 90% of the

other line pair length. In the example shown, the open circuit is located at around

89.7m from the tester. The open circuit line number could be rechecked using the

WIREMAP function.

Press the p key to return to the previous display or press the q key to show further

unpaired line number lengths. Press ‘PAIR&L’ to return to the main menu.

Coaxial cable and telephone line measurement function

After entering into the coaxial cable and telephone line, (Coax/Tel), measurement

function, the LAN Network Cable Tester will show a display typical to that shown

below:

It will display ‘OPEN’ if there are any open circuits or if the coaxial cable or

telephone line is not connected.

It will display ‘SHORT’ if there are any short circuits.

Press the p or q key to repeat the measurement or press the ‘PAIR&L’ key to

return to the main menu.

The far-end recogniser will sound a beep prompt if the cable connection is in a

normal condition.

Note:

For coaxial cable measurements, two BNC adaptor accessories are required. One is used to

connect the ‘M’ port RJ45 and the cable under test and the other adaptor is used to connect the

far-end matcher port ‘R’ and the cable under test.

For telephone line measurement, two RJ11 adaptors accessories are required. One is used to

connect ‘M’ port RJ45 and the cable under test and the other adaptor is used to connect the

far-end matcher port ‘R’ and the cable under test.

Calibration and setup, (SETUP), function:

When the Calibration and Setup function is selected, the LAN Network Cable Tester

will show a display typical to that shown below:

Press the p or q keys to move the cursor ‘->’ indicator up and down to the

required item and then press ‘PAIR&L’ to select the required setup function.

UNIT - This is used to set up the length unit. The options are metre (m) and feet (ft).

CALIBRATION -Selects the Calibration function (See Calibration section below).

QUIT - Return to the main menu.

Dynamic Calibration, (CALIBRATION), function:

Note: A shortcut to entering the ‘Dynamic Calibration’ function is to press and hold

the ‘PAIR&L’ key while switching on the LAN Network Cable Tester.

For an accurate measurement of cable length, the calibration operation should be

carried out as follows.

When Dynamic Calibration is selected, the tester shall display the following:

Press the p key to select ‘Yes’ and continue with the calibration.

Press the q key to select ‘No’ and exit the calibration function.

Insert a cable of given length into the ‘M’ port, there is no need to insert the far-end

recogniser.

Press the p key to select ‘Yes’ and start the measurement. The measured length is

displayed as below:

Hold the p and q keys (-/+) to display the length adjustment to achieve the actual

cable length and then press the ‘PAIR&L’ key to save the calibration factor and exit

the calibration function.

If the cable length being measured is too short (<5m), the following will be displayed

to prompt the user to use a longer cable for calibration. The user is also prompted

as to whether they want to continue calibrating or not.

Press the q key to select ‘No’ and exit the calibration function. Press the p key to

select ‘Yes’ and repeat the measurement.

If there is a fault on the cable being measured, a display typical to that below will be

shown to inform the user and to conrm whether or not to continue the calibration:

Press the q key to select ‘No’ and exit the calibration function. Press the p key to

select ‘Yes’ and repeat the measurement.

Note:

If the tester is restarted after it shuts off, the tester will recover the standard calibration factor of

Class UTP5 cable as setup during manufacture.

Technical Specication

Overall Dimension

180 x 80 x 40mm.

Power Supply

4 x 1.5V Size AA batteries with power consumption

16mA. (Included)

Display

Special 4 x 16 character big screen LCD

lattice (valid visual eld 61.6 x 25.2mm).

Type of test Cable

STP/UTP twin twisted cable. Coaxial cable, telephone

line.

Working Ambient Temp.

-10⁰ C to + 60⁰ C.

Tester Port

Test RJ45 master port (M), test LOOPBACK RJ45 port

(L), far-end Recogniser RJ45 port (R). The BNC and

RJ11 adaptor accessories can be used to measure and

check the continuity of coaxial cable and telephone

lines.

Twin Twisted Cable Length

Scope: 1 - 350m, (3 - 1,200ft)

Calibration Accuracy

3% (+/- 0.5m or +/- 1.5ft) (calibrating cable >5m)

Shipment Accuracy

5% (+/- 0.5m or +/- 1.5ft) (AMP, AT&T Class 5 cable)

Display

Meters or feet.

Length Calibration

The user can set the calibration factor with a given

length of cable. The length of the calibrating cable

should be more than 5m.

Wire Sequence and Locating

Cable Error

Check errors such as open circuit, short circuit, reverse

connection, cross-over or cross-talk interference.

Locating Cable

8 far-end passive test jacks (ID 1 ≥ ID 8)

Automatic Time-Delay Shut Off Time

30 minutes

Issue 2

*Triax reserves the right to change the specications without prior notication

Triax 157011 Operating instructions

Triax 157011 Operating instructions

Triax 157011 Operating instructions

Related papers

Other documents