AMQ ACTIV DT Riser Installation guide

Brand
AMQ
Model
ACTIV DT Riser
Type
Installation guide
ACTIV DT Riser installation guide
ACTIV DT RISER INSTALLATION GUIDE | 2
amqsolutions.com
M6X14
x4
Monitor Holder
M6X12
x4
Base
Dual Monitor Mount
Keyboard Tray Assembly
M6X12
x4
Keyboard Bracket
Monitor Holder
M6X10 Hand Screw
x4
Power Cord
Primary Worksurface & Handset
Support Plate
M6X25
x4
M4X10
x1
M6X8
x4
Dual MonitorKeyboard Tray
Column/Control Box
COMPONENTS
OPTIONAL
ACTIV DT RISER INSTALLATION GUIDE | 3
amqsolutions.com
M6X14
M6X8
Step 1
Use M6X14 screws (x4) to assemble base to
column. Wire the column to the control box.
Step 3
Slide the primary worksurface over
the column and set column to lowest
position.
Step 2
Use M6X8 screws (x4) to assemble the support plate
to pre-drilled holes at the bottom of column.
M6X25
Step 4
Wire the handset to the control box and plug in the power
cord.
Raise the column at least 8 inches. Use M6X25 screws (x4)
to mount te primary worksurface to support plate.
M6X12
M4X10
Step 5
Use M6X12 screws (x4) to attach monitor
holder to top of column. Remove the M4X10
screw under the monitor holder to release
the VESA plate. Attach the VESA plate to the
monitor and resecure to monitor holder with
the M4X10 screw.
INSTALLATION
ACTIV DT RISER INSTALLATION GUIDE | 4
amqsolutions.com
Step 1
Using the M6X12 screws (x4), attach the keyboard bracket to primary worksurface
via the predrilled holes on the bottom of primary worksurface.
Step 2
Insert Keyboard Tray Assembly into the Keyboard Bracket until the pin releases
and keyboard tray is firmly secured.
Installation of your DT Riser is complete.
M6X12
KEYBOARD TRAY
ACTIV DT RISER INSTALLATION GUIDE | 5
amqsolutions.com
M6X12
M6X10
hand screw
Step 1
Use M6X12 screws (x4) to attach the dual
monitor mount to top of the column.
Step 2
Prior to installing the monitors to the unit, use
the monitor mount screws from your monitor
to attach the VESA plates to each respective
monitor.
Note: Single monitor holder is re-used for the
dual monitor mount assembly.
Step 3
Use the M6X10 hand screws (x4) to fasten
monitor holder to dual monitor mount through
the horizontal cut-outs in the mount.
DUAL MONITOR MOUNT
ACTIV DT RISER INSTALLATION GUIDE | 6
amqsolutions.com
ADJUSTING VESA MOUNT TENSION
Step 1
Remove the M4X10 screw to
release the VESA mount.
Step 2
Take off rubber cover on the VESA
mount to expose the M8 screw.
Step 3
Use a 13mm wrench to adjust the M8 screw
on the VESA mount for appropriate tension
— clockwise to increase tension (for larger
monitors) and counterclockwise to decrease
tension (smaller monitors).
M4X10
ACTIV DT RISER INSTALLATION GUIDE | 7
amqsolutions.com
BOTTOM WIRING
Please contact [email protected] if you are
missing any parts, have difficulty with assembly,
or have any product related questions.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

AMQ ACTIV DT Riser Installation guide

Brand
AMQ
Model
ACTIV DT Riser
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents