2. Danfoss
  3. Compact Mixing Shunt, FHM-C

Danfoss Compact Mixing Shunt, FHM-C Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Danfoss Compact Mixing Shunt, FHM-C Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Compact Mixing Shunt, FHM-Cx
Instruction
1
© 10/2010 VI.UL.Q3.85 Danfoss Heating Solutions
FHM-FLFH-TC
FH-ST
FH-MS
GB Technical Data
Test pressure 16 bar
Max. working pressure 10 bar
Max. differential pressure 0.6 bar
Max. flow temperature 90° C
Note! Maximum operating pressure and temperature given by
the tube manufacturer must not be exceeded.
DK/N Tekniske data
Test tryk / test trykk 16 bar
Max. arbejdstryk / arbeidstrykk 10 bar
Max. differenstryk / differansetrykk 0,6 bar
Max. fremløbstemp. / medietemp. 90° C
NB! Maximum arbejdstryk / driftstrykk og temperatur opgivet af
oppgitt av rørleverandøren / rørprodusenten må ikke overskrides.
1 2 3 4 5 6 (max)
20°C 25°C 30°C 35°C 40°C 45°C 50°C
L/h
0 6 17
5
6
4
2
1
3
230V / 16A
T
S
55°C
PFM 3000/4000
kv
s
7,4
Danfoss
IN
OUT
6
5
4
2
1
3
GB 1. Drain the system for water.
2. Remove the FH-TC .
3. Remove the capillary sensor .
DK/N
1. Tøm systemet for vand.
2. Fjern FH-TC .
3. Fjern kapillarføleren .
GB 4. Replace the casket with a new (supplied in box) and mount
the adapter . Tighten the nut with app. 40 Nm.
5. The new sensor pocket is supplied with O-ring and is re-
placing the capillary sensor . Mount the pocket and tighten
with 20 Nm.
6. The sensor is pushed into the pocket and is kept in place
with a rubber ring
DK/N
4. Udskift pakningen med en ny (medfølger) og monter adapte-
ren . Stram møtrikken med ca. 40 Nm.
5. Den nye følerlomme leveres med O-ring, og den erstatter
kapillarsensoren . Monter lommen og stram med 20 Nm.
6. Sensoren skubbes ind i lommen og fastholdes af en gummi-
ring.
GB ECL 110 Settings for Floor Heating Applications
- maintenance menu 2175: change settings to 1.0.
- maintenance menu 2178: change settings to 55°C.
- application menu 7024: change actuator setting to ABV.
- application menu 7162: change knee point setting to OFF.
DK/N
ECL 110 indstillinger for gulvvarmeapplikationer
- vedligeholdelsesmenu 2175: indstilles til 1.0.
- vedligeholdelsesmenu 2178: indstilles til 55°C.
- applikationsmenu 7024: indstilles til ABV.
- applikationsmenu 7162: knækpunkt indstilles til OFF.
2
Danfoss Heating Solutions VI.UL.Q3.85 © 10/2010
Installation Guide Placement of ABV set for FHM-Cx shunts
/