Ferm BGM1005 Owner's manual

Type
Owner's manual

This manual is also suitable for

www.ferm.com 0511-25.1
UK Subject to change
D Änderungen vorbehalten
NL Wijzigingen voorbehouden
F Sous réserve de modifications
E Reservado el derecho de
modificaciones técnicas
P Reservado o direito a modificações
I Con riserva di modifiche
S Ändringar förbehålles
SF Pidätämme oikeuden muutoksiin
N Rett till endringer forbeholdes
DK Ret til ændringer forbeholdes
Art. no. BGM1005
FSMW-150
www.ferm.com
UK
D
NL
F
E
P
I
S
SF
N
DK
USERS MANUAL 03
GEBRAUCHSANWEISUNG 10
GEBRUIKSAANWIJZING 17
MODE D’EMPLOI 24
MANUAL DE INSTRUCCIONES 31
MANUAL DE INSTRUÇÕES 38
MANUALE UTILIZZATI 45
BRUKSANVISNING 52
KÄYTTÖOHJE 59
BRUKSANVISNING 66
BRUGERVEJLEDNING 73
2
83Ferm
Ferm
6
5
4
3
2
1
Fig. A
Fig. D
Fig. B Fig. C
1
2
3
4
5
6
7
8
Exploded view
Spare parts list FSMW-150
Position Description Ferm no.
1 Switch 206403
2 Support (right) 206454
4 Cover Glass holder wide 206408
5 Cover Glass 206401
6 Cover Glass holder small 206132
7 Support (left) 206405
8 Rubber foot 206143
Ferm
82
Ferm Ferm 3
BENCH GRINDER
The numbers in the following text refer to the drawing on page 2
For your own safety and for the safety of others, please read these instructions
carefully before using this appliance. It will help you understand your product more
easily and avoid unnecessary risks.
Keep this instruction manual in a safe place for future use.
Contents:
1. Machine data
2. Safety instructions
3. Installation
4. Operation
5. Maintenance
1. MACHINE DATA
Technical specification
Contents of packing
1 Bench Grinder
2 Sets eye shield bracket + eye shield
1 Tool rest (right)
1 Tool rest (left)
1 Users manual
1 Guarantee card
Check the machine, loose parts and accessories for transport damage.
Voltage | 230 V
Frequency | 50 Hz
Power input | 370 W
No load speed | 2950/min / S
2
=30 min
Grinding stone dimensions | Ø 150x20 mm
White grinding stone dimensions | Ø 150x40 mm
Spindle hole diameter | Ø 12.7 mm
Weight | 10 kg
Lpa (sound pressure) | 76 dB(A)
UK
Ferm 81Ferm
Features
Fig. A
1. On/off switch
2. Tool rest (right)
3. Eye shield
4. Eye shield bracket
5. Screw
6. Tool rest (left)
2. SAFETYINSTRUCTIONS
In this manual and/or on the machine the following symbols are used:
Read instructions carefully
In accordance with essential applicable safety standards of European directives
Denotes risk of personal injury, loss of life or damage to the tool in case of non-
observance of the instructions in this manual.
Indicates electrical shock hazard.
Immediately unplug the plug from the mains electricity in the case that the cord gets
damaged and during maintenance
Keep bystanders away
Wear ear and eye protection
Faulty and/or discarded electrical or electronic apparatus have to be collected at the
appropriate recycling locations.
Special safety instructions
When using the machine for the first time
Check the following:
Does the voltage rating of the bench grinder correspond to the power supply?
Is an earthed mains power socket available?
Are the power cord and plug in good condition (solid, without fraying or other damage)?
Avoid the use of long extension cords. The extension cords you use must always be earthed.
Agrinding wheel is a brittle toolpiece. The stone is not resistant to knocks.
4
UK
Ferm
80
DK
Ferm 5
Always grind on the front edge of the grinding wheel, and never on the side of the grinding
wheel. Never fit a cracked grinding wheel. Replace it immediately, as the high rotational
speed could cause the stone to fly apart, causing a serious accident.
Always wear safety glasses when grinding.
Never grind without the cover fitted over the grinding wheel.
Always fit the grinding wheel cover and tool rest tightly, and with the correct clearance.
Never allow more than 1-1.5 mm clearance between tool rest and grinding wheel.
Only use the grinding wheel for the work it was designed for (for example sharpening tools),
and NOT for heavy construction work.
The following information must be available, before you fit any new grinding wheel:
Details about the manufacturer.
Binding material.
Dimensions.
Permissible rotational speed.
Never ream out the hole in a grinding wheel to a larger diameter.
The maximum rotational speed of the grinding wheel should never be allowed to exceed
the maximum speed given for the wheel.
Never use any grinding wheel that is damaged or deformed.
In order to be able to grind safely, the machine must be firmly bolted to a workbench.
The tool rest should be replaced whenever the width of the tool rest measures less than
20 mm.
The recommended depth of the recess in the flange (T) is 2 mm and the diameter of the
spindle hole is 13 mm (see Fig. D).
Whenever using the machine
Check that the switch is NOT in the ‘ON/1’position before connecting the machine to the
power supply.
Always keep the power cord out of the way of the tool’s moving parts.
Immediately switch off the machine whenever:
The plug or power cord is defective or damaged.
The switch is defective.
You smell smoke or burning insulation.
Electrical safety
When using electric machines always observe the safety regulations applicable in your country
to reduce the risk of fire, electric shock and personal injury. Read the following safety
instructions and also the enclosed safety instructions.
Always check that the power supply corresponds to the voltage on the rating plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in the wall outlet.
UK
Ferm 79
CE
KONFORMITETSERKLÆRING (DK)
Vi erklærer herved, udelukkende på eget ansvar, at dette produkt opfylder følgende standarder
eller standardiserede dokumenter:
EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3, EN61029-1, EN61029-2-4
i overenstemmelse med direktivreglerne
98/37/EEC, 73/23/EEC, 89/336/EEC
Fra 01-10-2005
ZWOLLE NL
W. Kamphof
Quality department
Det er vores hensigt til stadighed at forbedre vores produkter, og vi forbeholder os derfor til
enhver tid retten til at ændre produktspecifikationerne uden forudgående varsel.
Ferm BV Lingenstraat 6 8028 PM Zwolle Holland
DK
Ferm
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable reel always unwind the reel completely.
3. INSTALLATION
The grinder must be firmly bolted to a workbench. The length of the fixing bolts will depend on
the thickness of the workbench. If the workbench is made of steel, it is advisable to use a
wooden block or plank between the grinder and the bench, to insulate it and prevent vibration.
Mounting and adjustment of eye shield bracket and eye shield
Fig. B
The eye shield bracket and eye shield should only ever be assembled/adjusted
with the grinding wheel stationary, and the machine disconnected from the power
supply.
Mount the holder of the cover glass together with the cover glass itself, by means of the
screw (A).
Adjust the height of the holder of the cover glass by loosening a bit screw . The free space
between the stone and the holder of the cover glass will amount to 1 - 1,5 mm.
Fasten well screw (A).
Adjust the cover glass (see the figure above) in such a way that your face will be protected,
at the utmost.
Use always safety glasses.
Adjusting tool rest
The tool rest should only be adjusted when the grinding wheel is completely statio-
nary, and the machine is disconnected from the power supply (the wall socket).
Secure the tool rest, allowing a maximum clearance (C) between the tool rest and the grinding
stone of 1 -1.5 mm.
Replacing the grinding stone
Fig. C
Required tools:
19 mm Spanner
8 mm Spanner
Screwdriver
Only ever replace the grinding wheel when the motor is at a standstill and the power
is completely disconnected.
Remove the guards, using the above tools. When replacing the stones, remember the
right-hand spindle is fitted with right-hand thread, the left-hand spindle with left-hand
thread.
6
UK
Ferm
Reparationer må udelukkende udføres af en autoriseret installatør eller et
autoriseret serviceværksted.
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til at
fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammoniak, osv.
Den slags stoffer beskadiger kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres på
en genbrugsplads.
Garanti
Læs det separat vedlagte garantikort for garantibetingelserne.
Den elektriske motor bliver
varm.
Der er tændt for maskinen,
men den kører ikke.
Motoren er blevet
overbelastet.
Motoren er defekt.
Der er en afbrydelse i
strømforsyningen til
maskinen.
Kontakten kan være
beskadiget.
Lad motoren afkøle.
Kontakt servicestedet.
Kontrollér, om der er et brud
på netledningen.
Kontakt servicestedet.
78
DK
Ferm 7
Loosen the nut by means of the spanner. Remove the stone.
Clean the flanges. Replace one flange, with the concave side facing the grinding stone.
Slide the new grinding stone on to the spindle. Replace the second flange on the spindle,
with the concave side facing the grinding stone. Tighten the nut securely, but not too tightly!
Replace the guards and adjust the tool rest. Let the motor run for a few seconds before you
start to grind.
4. OPERATION
Selecting the grinding wheel
Coarse grinding wheels will in general remove the most material, and fine grinding wheels are
used for finishing. If the surface is uneven, begin by using a coarse grinding wheel, and grind the
workpiece until it is smooth. Next use a fine grinding wheel to remove the grooves and
scratching left by the coarse wheel, and finish off the workpiece.
Grinding
To prevent the grinding surface from blocking up, avoid holding wood, lead or any other soft
material or metal against the grinding wheel. To avoid creating grooves, do not press the
workpiece too firmly on the grinding wheel. Use water to regularly cool the workpiece being
ground. Wood chisels and the like should never be sharpened ‘blue’.
Take care not to lose your grip on the object being ground, as it may suddenly become jammed
between the tool rest and the grinding wheel. This can cause the stone to shatter, the motor to
seize, or the workpiece to fly off, all of which can cause injury and damage.
Whenever the machine has been in use for 30 minutes, it should be switched off. Allow the
machine to cool down to room temperature.
Operation
Check that the switch is in the “OFF/0” position before connecting the machine to the power
supply.
Press the power switch into the “ ON/1” position to start your bench grinder.
Always keep the power cord out of the way of the tool’s moving parts.
5. MAINTENANCE
Make sure that the machine is not live when carrying out maintenance work on the
motor.
The Ferm machines have been designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends upon proper machine care and
regular cleaning.
Trouble shooting
Should the machine fail to function correctly, a number of possible causes and the appropriate
solutions are given below:
UK
Ferm 77
Udskift kun slibeskiven, når motoren står helt stille, og strømforsyning er frakoblet.
Fjern beskyttelsesskærmene vha. ovennævnte værktøj. Den højre akse har højredrejet
gevind. Den venstre akse har venstredrejet gevind. Tag hensyn til dette, hvis De udskifter
stenene.
Skru bolten løs med un brakonøglen. Tag den gamle slibesten af. Gør klemskruerne rene.
Sæt den nye slibesten på aksen ligeledes så den hule side vender mod slibestenen. Skru
derefter møtrikken på aksen, men ikke for stramt. Sæt nu beskyttelsesskærmen på plads
og justér anslaget. Lad motoren køre et øjeblik uden at slibe.
4. ANVENDELSE
Valg af slibeskive
Generelt fjerner grove slibestene det meste materiale og fine slibestene bruges til finpudsning.
Hvis overfladen er ujævn, slibes den først jævn med en grov slibesten. Derefter bruges en
finere slibesten til at fjerne de mærker, der er efterladt af den første slibesten samt til
finpudsning.
Sådan sliber du
Sørg for, at stenen ikke slibes til, hvis der holdes f.eks. træ, bly eller andet blødt metal mod
slibestenen. Tryk ikke slibeemnet for hårdt mod slibestenen, da der ellers kan opstå furer. Køl
værktøj, som skal slibes af med vand. Træmejsler må under ingen omstændigheder slibes
"blå". Sørg for, at slibeemnet ikke kan glide ud af hånden og sætte sig fast mellem anslaget og
slibestenen under slibningen. Derved kan stenen nemlig springes, motoren kan brænde
sammen eller slibeemnet kan slå tilbage, hvilket kan medføre personskader.
Sådan tænder du for maskinen
Kontrollér, at afbryderen står på "0", før stikket sættes i stikkontakten.
Tryk afbryderen ind for at starte den stationære slibemaskine.
Hold altid strømkablet væk fra de bevægende dele.
5. SERVICE & VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under strøm, når der udføres
vedligeholdelsesarbejder på mekanikken.
Maskinerne fra Ferm er udviklet til at fungere længe uden problemer med et minimum af
vedligeholdelse. Ved at rengøre maskinen regelmæssigt og behandle den korrekt, bidrager De
til en længere levetid for maskinen.
Fejl
For det tilfælde, at maskinen ikke fungerer korrekt, er herunder angivet en række mulige
årsager med tilhørende løsningsforslag:
DK
Ferm
Repairs and servicing should only be carried out by a qualified technician or service
firm.
Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the
ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.
Faults
Should a fault occur, e.g. after wear of a part, please contact the service address on the warranty
card. In the back of this manual you find an exploded view showing the parts that can be
ordered.
Environment
To prevent damage during transport, the appliance is
delivered in a solid packaging which consists largely of reusable material. Therefore please
make use of options for recycling the packaging.
Faulty and/or discarded electrical or electronic apparatus have to be collected at the
appropriate recycling locations.
Warranty
The guarantee conditions can be found on the separately enclosed guarantee card.
The electric motor becomes
hot
Machine switched on, but
will not run
The motor has become
overloaded.
The motor is defective.
There is a break in the
power supply to the
machine.
The switch may be
damaged.
Give the motor a chance to
cool down.
Contact the service point.
Check whether there is a
break in the power cord.
Contact the service point.
8
UK
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Ferm BGM1005 Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI