PAC BKHYNK1120 User manual

Brand: PAC

Model: BKHYNK1120

Type: User manual

This manual is also suitable for

HYNK1120

PAC BKHYNK1120 is a car radio installation kit for select Hyundai and Kia vehicles. It allows you to replace your factory radio with a new aftermarket radio. The kit includes all the necessary hardware to install your new radio, including brackets, screws, and a wiring harness.

The PAC BKHYNK1120 is compatible with the following vehicles:

Hyundai Accent (2006-2011)
Kia Rio (2006-2010)
Kia Sportage (2005-2010)
Kia Sorento (2007-2010)

The kit is easy to install and comes with detailed instructions.

The PAC BKHYNK1120 is compatible with the following vehicles:

Hyundai Accent (2006-2011)
Kia Rio (2006-2010)
Kia Sportage (2005-2010)
Kia Sorento (2007-2010)

The kit is easy to install and comes with detailed instructions.

CUSTOMER HELP LINE

USA 800-323-4329 • Canada 800-245-8777

HYNK1120 Mounting Kit

Hyundai

2006-11 ACCENT

Kia

2006-11 RIO

2007-10 SORENTO

2005-10 SPORTAGE

VEHICLE APPLICATIONS

iHYNK1120

TECH Ver. 4/14 PRINT Ver. 4/15

2500 East Francis Street Ontario, CA 91761, U.S.A.

USA Sales (800) 336-6500

Canada Sales (888) 922-3006

For information about other American International automotive

accessories visit our website at:

http://www.aius.net

1. Carefully pry radio/vent trim bezel forward, disconnect the harnesses attached to the

rear of the bezel and remove bezel. (This requires soft panel removal tools)

2. Remove the (4) Phillips screws securing the radio to the sub-dash, carefully pull radio

forward, disconnect the wire harness and antenna lead and remove radio.

DASH DISASSEMBLY

006-11 HYUNDAI ACCENT

2006-10 KIA RIO

2005-10 KIA SPORTAGE

DASH DISASSEMBLY

1. Carefully pry radio/Climate control trim bezel forward, disconnect all harnesses

attached to the rear and remove bezel.

2. Remove the (4) Phillips screws securing the radio to the sub-dash.

3. Pull radio forward, disconnect the wire harness and antenna lead and remove radio.

KIT ASSEMBLY INSTRUCTIONS

1. See page 3 for Bracket Preparation.

2. Attach the left and right side brackets to the main bracket.

3. Attach left and right side brackets to the rear of the pocket using small screws

supplied with kit.

DIN MOUNT INSTRUCTIONS

1. Insert DIN sleeve from your new radio into the upper section of the installation kit.

(This DIN sleeve comes with all new radios and slides off the back of the radio)

2. Depress the tabs from inside the sleeves opening upward, outward, and downward

to secure sleeve to the installation kit.

3. Install radio into sleeve and lock into place.

4. Support rear of radio with back strap.

Optional use Trim Ring (ITR-1120) may be used on some radios if desired.

Due to the movement of some faces on some radios our ISO Trim Ring may not be able

to be used. You may also ISO mount your radio. See page 4.

Your new radio must have a trim ring around the face of the radio that is designed to be

easily removed. Consult your radio ownerʼs manual.

DIN Sleeve

ITR1120

Trim Ring

(optional use)

NOTES

6 3

BRACKET PREPARATION

HYUNDAI ACCENT

KIA RIO

KIA SPORTAGE

Remove shaded tabs on

Left & Right brackets

Remove shaded tabs on

Left & Right brackets

Remove shaded tabs on

Left & Right brackets

NOTES

4 5

ISO MOUNT INSTALLATION INSTRUCTIONS

NOTE: Some radio faces are larger in size than the ITR1120 Trim Ring allows.

You may need to file the Trim Ring opening larger for some radios.

1. See page 3 for Bracket Preparation.

2. Attach the left and right side brackets to the main bracket. See illustration below.

3. Attach left and right side brackets to the rear of the pocket using screws

supplied w/kit.

4. Attach ISO Mount Spacers to the inside of upper section on both Left & Right

mounting brackets as shown in Figure A below.

5. Slide radio into kit from rear & attach to ISO mounting brackets using screws supplied

with radio (do not tighten screws at this time). (Be sure the length of the screws DO

NOT touch any electrical parts inside radio, some screws may need to be shortened.)

6. Slide radio forward or backward for your desired look and then tighten the mounting

screws. Use ISO trim ring when possible.

7. Attach rear support strap (supplied with radio) to rear of pocket and to rear of radio.

NOTE: Optional ISO trim ring (ITR1120 included) may be used in place of after-market

radioʼs trim ring. For ISO mount applications, mount after-market radio to side

brackets using hardware included.

Fig. A

ITR1120

Trim Ring

(opt

ional use)

1. Carefully pry outward and remove the individual side trims located beside the

Climate controls and storage pockets.

2. Remove the (2) Phillips screws securing the Radio trim bezel.

3. Carefully unclip and pull forward the radio trim bezel, disconnect all attached

harnesses and remove radio trim bezel.

4. Remove the Individual screw securing each left and right vents/trim panel,

carefully pull the panels forward and remove.

5. Remove the (4) Phillips screws securing the radio to the sub-dash, pull radio forward

and disconnect all harnesses and antenna lead and remove radio.

DASH DISASSEMBLY

2007-10 KIA SORENTO

BRACKET PREPARATION

KIA SORENTO

Remove ONLY shaded

tabs on Left & Right

brackets

DO NOT REMOVE

tabs on Left & Right

brackets

Remove ONLY shaded

tabs on Left & Right

brackets

PAC BKHYNK1120 User manual

Brand: PAC

Model: BKHYNK1120

Type: User manual

This manual is also suitable for

HYNK1120

The PAC BKHYNK1120 is compatible with the following vehicles:

Hyundai Accent (2006-2011)
Kia Rio (2006-2010)
Kia Sportage (2005-2010)
Kia Sorento (2007-2010)

The kit is easy to install and comes with detailed instructions.

Download PDF

report

PAC BKHYNK1120 User manual

This manual is also suitable for

PAC BKHYNK1120 User manual

Related papers

Other documents