Savant FTK-FTEST-00 User guide

Savant
Brand
Savant
Model
FTK-FTEST-00
Type
User guide

This manual is also suitable for

Savant FTK-FTEST-00 is a multi-functional test device used to conduct electrical measurements and tests. It combines 7 different functions in one unit, making it a versatile tool for technicians and engineers. The device can perform continuity, insulation, and ground resistance tests, as well as measure voltage, current, and resistance. Additionally, it can also be utilized for insulation resistance testing and dielectric absorption ratio (DAR) measurement.

Savant FTK-FTEST-00 is a multi-functional test device used to conduct electrical measurements and tests. It combines 7 different functions in one unit, making it a versatile tool for technicians and engineers. The device can perform continuity, insulation, and ground resistance tests, as well as measure voltage, current, and resistance. Additionally, it can also be utilized for insulation resistance testing and dielectric absorption ratio (DAR) measurement.

Fiber Cleaver Operation Manual
1. Open the clamp cover and fi ber holder
lid. Place the prepared fi ber in the fi ber holder
v-groove according to need in order to determine
the cleaving length, based on connector
requirement. Ensure fi ber is long enough to lay
across both black pads.
2. *Clamp cover:
Utilize only as needed. Note that
fi ber must be positioned straight and at a 90° angle
to the blade wheel.
Push the blade carriage sliding
block forward fi rmly.
3. Open the clamp cover. Carefully pick out the
cleaved optical fi ber. Do not allow the cleaved fi ber
to touch anything prior to insertion into connector
to avoid contamination.
Important Safety Precautions
• Read user manual carefully before use.
• Do not get the fi ber cleaver wet. Avoid humid or
dusty environments. Avoid high temperatures to
prevent deformation.
• This is a precision instrument. Avoid drops or
impact to this unit.
• Regularly clean blade, holder lid, and fi ber holder
groove with alcohol. Do not use acetone or
corrosive fl uxing agents to clean blade.
Clean with Alcohol
Periodically clean fi ber holder groove, fi ber holder
lid, and blade edge. Do not use acetone or
corrosive fl uxing agent to clean.
Fiber Cleaver Operation Steps
Preparing fi ber involves removal of colored
soft peel coating per instruction steps
included with SSF™ connectors. Do not
attempt to cleave fi ber that has not been
prepared.
Fiber Cleaver Operation Manual
Adjusting the Blade Position
If fi ber cleaver cannot successfully cleave, or if blade cutting point can’t be used again, it is necessary to
change the blade cutting point (the blade with cutting point 1-12).
1. Unscrew the fastening screw of the blade,
turning in a counter-clockwise direction with a
screwdriver. Rotate blade by one postion to the
next number (original number on blade plus one),
then tighten screw.
Blade Replacement
Once all 12 positons on the blade have been utilized, it is necessary to replace the blade.
1. Unscrew the screw that connects the blade
carriage sliding block.
2. Loosen the blade clamping screw.
3. Carefully remove the blade carriage. Unscrew
the blade fastening screw to remove the blade and
insert new blade. Rotate blade and place number
1 on the uppermost position, the tighten the
screws.
4. Fasten the blade carriage on the blade sliding
block, then tighten the fastening screws.
5. Adjust the adjustment screw of blade carriage.
Blade Height Adjustment
If fi ber does not cleave, ensure all steps have been
followed prior to adjustment. Refer to SSF™ blade
height adjustment procedure included with this
cleaver.
  • Page 1 1
  • Page 2 2

Savant FTK-FTEST-00 User guide

Savant
Brand
Savant
Model
FTK-FTEST-00
Type
User guide
This manual is also suitable for

Savant FTK-FTEST-00 is a multi-functional test device used to conduct electrical measurements and tests. It combines 7 different functions in one unit, making it a versatile tool for technicians and engineers. The device can perform continuity, insulation, and ground resistance tests, as well as measure voltage, current, and resistance. Additionally, it can also be utilized for insulation resistance testing and dielectric absorption ratio (DAR) measurement.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents