Metropolitan Front Assembly Conversion (WIK/WIF)
Removal
1. Remove the front faceplate by pulling the faceplate away from the
faceplate retainer.
2. Remove power from the keypad by toggling the Service Switch to
the Off position.
3. Remove the (2) 6-32 x ¼ inch flathead screws from the faceplate
retainer and remove the retainer.
4. Remove the round knob by grasping the beveled portion at bottom
of the knob with your thumb and forefinger and pull knob outward.
5. Using a small Phillips screwdriver, remove the (4) M2 x 4 mm flathead
screws (See image).
6. Remove the Front Assembly from the body of switch.
Installation (Skip steps 1 and 2 if converting a WIF)
1. If converting a WIK-xxx104, position the keypad buttons into their
desired position with the small light pipe window oriented towards
the top of the Front Assembly (Keypad buttons are not preinstalled).
2. Press firmly in the center of each button until all four corners snap into position.
3. Toggle the Service Switch on the new Front Assembly to the same position as the Front Assembly removed.
4. Carefully set the Front Assembly onto the body of the Metropolitan device. Verify the assembly is oriented correctly.
5. Install the four screws removed earlier that secure the Front Assembly. Do not overtighten screws.
6. Install the retainer using the (2) 6-32 x ¼ inch screws removed earlier.
7. Install the faceplate over the faceplate retainer.
8. Toggle the Service Switch to the On position. After software loads, verify operation of the Metropolitan device.
Metropolitan Front Assembly Conversion - Quick Reference Guide
Metropolitan Front Assembly Conversion - Quick Reference Guide
Metropolitan Front Assembly Conversion - Quick Reference Guide
Metropolitan Front Assembly Conversion - Quick Reference Guide
45 Perseverance Way, Hyannis, MA 02601
009-1376-00 | 151001 | Copyright © 2015
1
of
2
Savant.com | 508.683.2500
Metropolitan Front Assembly Conversion (WID/WIS/WI3)
Removal
1. Remove the front faceplate by pulling the faceplate away from
the faceplate retainer.
2. Remove power from the keypad by toggling the Service Switch
to the Off position.
Note: The WI3 does not have a Service Switch. Power will need to be
switched Off at breaker box.
3. Remove the (2) 6-32 x ¼ inch flathead screws from the faceplate
retainer and remove the retainer.
4. Using a small Phillips screwdriver, remove the (4) M2 x 4 mm
flathead screws (See image).
5. Remove the Front Assembly from the body of switch.
Installation
1. Toggle the Service Switch on the new Front Assembly to the
same position of the Front Assembly removed.
2. Carefully set the Front Assembly onto the body of the Metropolitan device. Verify the assembly is oriented correctly.
3. Install the four screws removed earlier that secure the Front Assembly. Do not overtighten screws.
4. Install the retainer using the (2) 6-32 x ¼ inch screws removed earlier.
5. Install the faceplate over the faceplate retainer.
6. Toggle the Service Switch to the On position. After software loads, verify operation of the switch.
Metropolitan Front Assembly Conversion - Quick Reference Guide
Metropolitan Front Assembly Conversion - Quick Reference Guide
Metropolitan Front Assembly Conversion - Quick Reference Guide
Metropolitan Front Assembly Conversion - Quick Reference Guide
45 Perseverance Way, Hyannis, MA 02601
009-1376-00 | 151001 | Copyright © 2015
2
of
2
Savant.com | 508.683.2500
-
1
-
2
Savant WIK-BKCONV-00 Reference guide
- Type
- Reference guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Savant WIK-BKCONV-00 Reference guide
-
Savant WIB-LAS106-00 Reference guide
-
-
-
Savant WPB-BKLV02-00 Reference guide
-
Savant WP3-SW0002-00 Reference guide
-
Savant WIB-LAS106-00 Reference guide
-
-
-