LBL Lighting WS979LNSCLED930 Installation guide

LBL Lighting
Brand
LBL Lighting
Model
WS979LNSCLED930
Category
Mounting kits
Type
Installation guide

This manual is also suitable for

LBL Lighting WS979LNSCLED930 is a Jarvas Wall light that is suitable for damp locations. It can mount either to a 4” square electrical box with a round plaster ring or an octagon electrical box. It may be dimmed with a low-voltage electronic dimmer. It features shade supports at each end to help secure shades in place. The fixture screws connect the fixture to the wall plate and the cap screws secure the shade to the fixture. The light comes with #8-32 screws for mounting the plate, end cap screws, backplate screws, cap screws with nylon washers, and a driver.

LBL Lighting WS979LNSCLED930 is a Jarvas Wall light that is suitable for damp locations. It can mount either to a 4” square electrical box with a round plaster ring or an octagon electrical box. It may be dimmed with a low-voltage electronic dimmer. It features shade supports at each end to help secure shades in place. The fixture screws connect the fixture to the wall plate and the cap screws secure the shade to the fixture. The light comes with #8-32 screws for mounting the plate, end cap screws, backplate screws, cap screws with nylon washers, and a driver.

1
Installation Instructions for
Jarvas Wall
980JARVASW
GP I :ENERAL RODUCT NFORMATION
This product is suitable for damp locations.
This product can mount either to a 4” square electrical box with a
round plaster ring or an octagon electrical box.
May be dimmed with a low-voltage electronic dimmer.
This instruction shows a typical installation.
1.0
W 979S
CAUTION RISK OF FIRE-
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
Wall
Remove the fixture screws located on the sides of the
fixture base.
Remove the mounting plate from the fixture base.
1
2
1A
FIXTURE
SCREW
1
1
Install the Mounting Plate
Attach the mounting plate to the electrical box using
the two #8-32 screws provided.
3
1B
3
#8-32 SCREW
MOUNTING
PLATE
3
2
2A
Install the Shade Support End Caps
FIXTURE BODY
BACKPLATE
SCREW
Loosen the four backplate screw to separate the fixture
body from the back plate.
1
2C
END CAP
WITH SHADE
SUPPORT
Install the provided end caps with shade supports.
(Reverse of 2B.)
Reattach the fixture body with the backplate. (Reverse
of 2A.)
3
2B
END CAP
END CAP
SCREW
Loosen the two end cap screws on each end of the
fixture body and remove the standard end caps.
2
4
DRIVER
BACKPLATE
C AUTION: Do not pull wires out of the fixture body.
3
Connect the mounting plate ground wire to a suitable
ground according to local electrical codes.
Connect the black driver wire to the hot power line wire
with a wire nut.
Connect the white driver wire to the neutral power line
wire with a wire nut.
Properly place the driver, all wires, and wire nut
connections into the fixture base.
Mount the fixture by sliding it back onto the mounting
plate and reinstalling the fixture screws (reversal of
figure 1B).
1
3A
2
1
3
2
4
Install the Fixture
5
DRIVER
4A
Install the Shade
SHADE
CAP
SCREW
SHADE SUPPORT
Align the holes in the shade with the shade supports at
each end.
Secure the shade in place with the provided cap screws
and nylon washers.
1
2
3
NYLON
WASHER
SAVETHESE INSTRUCTIONS!
1
© 2017 Lighting.All rights reserved.The " Lighting" graphic is aLBL LBL
registered trademark of Lighting. Lighting reserves the right toLBL LBL
change specifications for product improvements without notification.
7400 Linder Ave, Skokie, 60077IL
800.323.3226 - 847.626.6300
www.lbllighting.com
A Generation Brands Company
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

LBL Lighting WS979LNSCLED930 Installation guide

LBL Lighting
Brand
LBL Lighting
Model
WS979LNSCLED930
Category
Mounting kits
Type
Installation guide
This manual is also suitable for

LBL Lighting WS979LNSCLED930 is a Jarvas Wall light that is suitable for damp locations. It can mount either to a 4” square electrical box with a round plaster ring or an octagon electrical box. It may be dimmed with a low-voltage electronic dimmer. It features shade supports at each end to help secure shades in place. The fixture screws connect the fixture to the wall plate and the cap screws secure the shade to the fixture. The light comes with #8-32 screws for mounting the plate, end cap screws, backplate screws, cap screws with nylon washers, and a driver.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents