Q51 Configuration Guide
with RAS
2019/05/28
www.acti.com
CONFIGURATION GUIDE
2
Part one: Access the Camera
1. Open IP Utility on the desktop.
2. Find the Q51 camera you would like to install.
3. Open IE browser. (Please be sure to use IE browser.)
4. Enter the IP address of Q51 to connect by using IE browser.
5. Enter the account / password (admin/123456) and login to the web
configurator of Q51.
www.acti.com
CONFIGURATION GUIDE
3
6. Click on the camera icon to take a snapshot of the camera view,
name the picture file as “eMap” and save it on the desktop.
Note: This step will be used in Part two “(Step 5) – Heat Map, Increase eMap
settings”.
7. Click on the tool icon to enter the settings page of Q51.
www.acti.com
CONFIGURATION GUIDE
4
8. Adjust the camera to the correct time according to the figure below.
8.1 Click “Date & Time”
8.2. Click “Set Manually” and then adjust the time
8.3 Click “Apply” to save.
9. Please set the network parameters according to the following figure.
9.1. Click “IP Setting”
9.2. Click “Connection Type”
9.3. Click “Static IP Address”
9.4. Configure the related IP parameters
9.5. Click “Apply” to save the settings.
www.acti.com
CONFIGURATION GUIDE
5
10. Please set the parameters according to the following figure.
10.1. Click “Video”
10.2. Click “Intelligent Video”
10.3. Click “Reporting Server”
10.4. Configure the related server parameters (Please follow the example
shown below)
- Server 1 :Please tick
- Network Address: Please enter the IP address set by the installed
Server (MGB Server)
- Network Port: Please enter “8082”
- Account: Please enter “admin”
- Password: Please enter “123456”
10.5. Click “Apply” to save the settings.
www.acti.com
CONFIGURATION GUIDE
6
11. Please set the Location parameters according to the following figure.
11.1. Click “Location”
11.2. IVS Server Name: Please fill in the store name, Ex: ACTi)
Note: This will be used in Part two (Settings of adding device). Write
down the name you have set on a piece of paper.)
11.3. Store: Please fill in the installation position of the Camera, Ex: Gate)
Note: This will be used in Part two (Settings of adding device). Write
down the name you have set on a piece of paper.)
11.4. Click “Apply” to save the settings.
www.acti.com
CONFIGURATION GUIDE
7
12. Please set the HeatMap parameters according to the following figure.
12.1 Click “Intelligent video”
12.2 Click “Heatmap” on the setting page
12.3 After entering the setting page, click “Setup” to start
12.4 Draw the analysis range as shown in the following figure, you can draw
polygons to avoid the range that does not need to be detected, please try to
avoid the light or screen.
www.acti.com
CONFIGURATION GUIDE
8
12.5 Click “Setup”, then click “Get” to confirm the screenshot of the live
environment.
12.6 Refer to the illustration and the following text to set
1. Check “Enabled”
2. Active on -> Tick all
3. Start Time: 00:00
4. End Time: 24:00
5. Reporting Server: All
12.7 Click “Apply” to save the settings.
www.acti.com
CONFIGURATION GUIDE
9
13. Please set the HeatMap parameters according to the following figure.
13.1 Click “Intelligent video”
13.2 Click “Dwell time” on the setting page
13.3 After entering the setting page, click “Setup” to start.
www.acti.com
CONFIGURATION GUIDE
10
13.4 Draw the analysis range as shown in the following figure, you can draw
polygons to avoid the range that does not need to be detected, please try to
avoid the light or screen.
13.5 Click “Setup”, then click “Get” to confirm the screenshot of the live
environment.
13.6 Refer to the illustration and the following text to set
1.Check ”Enabled”
2.Active on -> Tick all
3.Start Time:00:00
4.End Time:24:00
5.Reporting Server:All
13.7 Click “Apply” to save the settings.
www.acti.com
CONFIGURATION GUIDE
11
Part two: Set up related parameters for the webpage
1. Open the webpage (Using Google chrome browser)
http://localhost/MAS_RetailPackage/Setting/mgbmanagement.aspx
2. Sign in RAS (admin/123456)
3. Settings of adding device
3.1 Click “Overview”→ “Setting”→“MGB Server”
3.2 Click the same name as the one attached to the server.
(Ex: MGB Server)
3.3 Click “Add new device” as the picture below
www.acti.com
CONFIGURATION GUIDE
12
3.4 Choose “Q51” for the Device Type (Please refer to the picture below)
www.acti.com
CONFIGURATION GUIDE
13
3.5 Set up the details of device
Camera Name:
(Store name +51+location)
IVS Server Name:
Store name (EX.ACTi)
Store Name:
Q51 Installation position
(EX.Gate)
Stream URL: Please keep
it blank.
Camera IP: Please keep it
blank.
Account:admin
Password:123456
3.6 Click “ Save”
3.7 Be sure all the devices have been set properly, then click “Lock” .
Click “Lock”→ “Save”
（If there are still other devices that need to be added (except Q51), please click
“Lock” after all the devices have been set without error.）
Note: The saved settings cannot be changed after clicking “Lock”！
（If there’s any setting error and need to adjust, please contact with ACTi
customer service to unlock.）
www.acti.com
CONFIGURATION GUIDE
14
4. Store Settings
Click” Setting”→” Store”
1. Click “Add Store”
2. Click “Enabled”
3. Name: Store name
4. Address: Enter the address and set the location (click sign)
5. Bussiness Hour: Confirm with the customer and set the store opening
hours
6. Enter Customer Number
7. Select “HeatMapDwell Device” same as the device we mentioned
above.
8. Press “Save”
9. Click “Lock”, then press “Save” again for the settings
（Please wait for the store to complete the related information, click “Lock”
after confirmation.）
7
www.acti.com
CONFIGURATION GUIDE
15
Note: The saved settings cannot be changed after clicking “Lock”！
（If there is any setting error or there is a need to adjust, please contact
ACTi customer service to unlock.）
4. Permission
1. Click “Setting”
2. Click “UserManagement”
3. Click “Add a User”
4. Account Name：Fill in the login account
5. Email：Fill in the Email
6. Password：Fill in the Password
7. Role：Select “Manager”
8. Store：Click the store you set on step 4.
9. Click “Save” for the settings
www.acti.com
CONFIGURATION GUIDE
16
5. HeatMap - Increase eMap settings
1. Click “Setting”→ “Heat Map”
2. Click “Add eMap”
3. Click “Upload eMap”
4. Click the camera icon to open the picture you saved in Part one
5. Click “Open file”
6. Click “Save”
7. Drag Q51 to the actual installation position as shown below
Copyright © 2019, ACTi Corporation All Rights Reserved
7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan
114, R.O.C.
TEL : +886-2-2656-2588 FAX : +886-2-2656-2599
Email: [email protected]
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ACTi R41CF-30 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
EUCHNER MGB-L0xx-AP Series Operating Instructions Manual
-
-
CTC Union SVP Express User manual
-
DataVideo MGB-5 User manual
-
UTICA BOILERS MGB Series II/MGC Series Quick start guide
-
-
EarthMark MGB-HB45 Specification
